Before Installation Clause Samples

Before Installation. Make sure to install the software in the following order. 1) Install the Application software (refer to 2.1 Installing FusionHDTV Applications) 2) Install Hardware(Board) (refer to 3.3 Board Installation) 3) Install Windows ME Driver (refer to 2.2.2 Installing Windows ME driver) 4) Check Windows ME device manger (refer to 2.2.3 Checking Windows ME Driver)
View SourceView Similar (3)
Before Installation it shall be the Licensee'5 obligation to carry out all tasks necessary to fulfil the requirements described in the Appendices of the Licence Agreement, which are a prerequisite for Installation. The Licensee shall also ensure that the equipment on which installa- tion is to take place is dedicated thereto and is in good working order and operating condition.
View Source
Before Installation. Before TPS can install the Advanced mapping feature, you must utilize ArcGIS web services and have the following ready:  A Standard or Advanced edition ArcGIS Server  An Address Locater/Geocoder service with same spatial reference as the base map  A Geometry service  If hosting your own maps, Network Analysis Extension needs to be installed.
View Source
Before Installation. Place SPC horizontally in the room where it will be installed. The room should remain between 18 and 22 degrees Celsius 48 hours before installation, and during the installation period. Do not remove the planks from the box during this acclimatization period.
View Source
Before Installation. Each new reel of fiber shall be pre-tested with an OTDR for length and transmission anomalies while on the reel immediately after receipt. If any anomaly is detected, the reel will be rejected and returned to the manufacturer for replacement.
View Source
Before Installation. Warning: 1) Before installing, first touch the grounded part of the PC to protect the components on the board from static electricity. 2) Before installing the board, the system’s power should be turned off. Installing the Board when the system’s power is “ON,” will damage the system or the Board. 3) Please remove the power cord from the PC.
View Source

Related to Before Installation

  • Software Installation The AGENCY shall request approval in writing from the COUNTY prior to installation of any software on COUNTY computer equipment. All software installations must be supervised by COUNTY technical support staff and proof of licensing is required. Upon completion, the AGENCY is responsible for reconfiguring the computers back to the original state.

  • Equipment Installation In order to meet its obligations under this Agreement, a Party that owns, rents, or leases equipment (the equipment owner) may require installation of such equipment on property owned by another Party (the property owner), provided that the property is being used for an electric utility purpose and that the property owner shall not be required to do so if it would thereby be prevented from performing its own obligations or exercising its rights under this Agreement.

  • Utility Installations Trade Fixtures Alterations 8.3.1 The term “Utility Installations” refers to all floor and window coverings, air and/or vacuum lines, power panels, electrical distribution, security and fire protection systems, communication cabling, lighting fixtures, HVAC equipment, plumbing, and fencing in or on the Premises. The term “Trade Fixtures” shall mean Lessee’s machinery and equipment that can be removed without doing material damage to the Premises. The term “Alterations” shall mean any modification of the improvements, other than Utility Installations or Trade Fixtures, whether by addition or deletion. “Lessee Owned Alterations and/or Utility Installations” are defined as Alterations and/or Utility Installations made by Lessee that are not yet owned by Lessor pursuant to Section 8.4.1.

  • Lending Installations Each Lender may book its Loans at any Lending Installation selected by such Lender and may change its Lending Installation from time to time. All terms of this Agreement shall apply to any such Lending Installation and the Loans and any Notes issued hereunder shall be deemed held by each Lender for the benefit of any such Lending Installation. Each Lender may, by written notice to the Agent and the Borrower in accordance with Article XIII, designate replacement or additional Lending Installations through which Loans will be made by it and for whose account Loan payments are to be made.

  • Installation When installation is required, the Contractor shall be responsible for placing and installing the Commodities or parts in the required locations at no additional charge. All materials used in the installation shall be of good quality and shall be free of defects that would diminish the appearance of the Commodity or render it structurally or operationally unsound. Installation includes the furnishing of any equipment, tools, rigging, labor, and materials required to install or replace the Commodities or parts in the proper location. Contractor shall protect the site from damage and shall repair damages or injury caused during installation by Contractor or its employees or agents. If any alteration, dismantling, excavation, etc., is required to achieve installation, the Contractor shall promptly restore the structure or site to its original condition. Contractor shall perform installation work so as to cause the least inconvenience and interference with Customers and with proper consideration of others on site. Upon completion of the installation, the location and surrounding area of work shall be left clean and in a neat and unobstructed condition, with everything in satisfactory repair and order.