Prime Wafer definition

Prime Wafer means the raw silicon wafers required, on a product-by-product basis, to manufacture Probed Wafers.
Sample 1Sample 2Sample 3

Examples of Prime Wafer in a sentence

  • Panasonic shall pay to the Company the purchase price for Products delivered in accordance with the Price Table plus the Prime Wafer Price (the “Purchase Price”).

  • The Borrower hereby waives ------------------------ and releases any Expense now or hereafter existing against any Indemnitee arising out of death or personal injury to personnel of the Borrower, loss or damage to property of the Borrower, or the loss of use of any property of the Borrower, which results from or arises out of the condition, use or operation of the Engines, including, without limitation, any latent or patent defect whether or not discoverable.

  • Silicon wafers (Prime Wafer) served as substrates for XPS measurements of the MnCl4-based hybrid LB film.

Related to Prime Wafer

  • Prime coat means the first of two or more films of coating applied to a metal surface.

  • Design torso angle means the angle measures between a vertical line through the "R" point and the torso line in a position which corresponds to the design position of the seat-back established by the vehicle manufacturer;

  • Synchronous Optical Network (SONET means the optical interface standard that allows inter-networking of transmission products from multiple vendors. The base rate is 51.84 Mbps (“OC 1/STS 1”) and higher rates are direct multiples of the base rate, up to 13.22 Gbps.

  • Asynchronous store and forward means the transmission of a patient's medical information from an originating site to the health care provider for telehealth at a distant site without the presence of the patient.

  • lb means pound.

  • prime mover means every engine, motor or other appliance which provides mechanical energy derived from steam, water, wind, electricity, the combustion of fuel or other source;

  • Prime Vendor – means any person (natural or juristic) who forwards an acceptable proposal in response to this RFB with the intention of being the main contractor should the proposal be awarded to him/her.

  • Load means energy consumed by Customers together with allocated losses and unaccounted for energy;

  • Design-bid-build means a project delivery method in which:

  • Intel means Intel Corporation, a Delaware corporation.

  • BOM means bill of material.

  • Digital Signal Level 0 (DS-0 means the lowest-level signal in the time division multiplex digital hierarchy, and represents a voice-grade channel operating at either the 56 Kbps or 64 Kbps transmission bit rates. There are twenty-four (24) DS-0 channels in a DS-1.

  • Cisco “we” “our” or “us” means Cisco Systems, Inc. or its applicable Affiliate(s).

  • Touch-up coating means a coating used to cover minor coating imperfections appearing after the main coating operation.

  • Check Meter means the Buyer revenue-quality meter section(s) or meter(s), which Buyer may require at its discretion, and which will include those devices normally supplied by Buyer or Seller under the applicable utility electric service requirements.

  • licensed water supplier means a company which is the holder for the time being of a water supply licence under Section 17A(1) of the 1991 Act(f);

  • Finished water means the water that is introduced into the distribution system of a public water system and is intended for distribution and consumption without further treatment, except as treatment necessary to maintain water quality in the distribution system (e.g., booster disinfection, addition of corrosion control chemicals).

  • Furniture coating means any paint designed for application to room furnishings including, but not limited to, cabinets (kitchen, bath and vanity), tables, chairs, beds, and sofas.

  • HRS means the Hawaii Revised Statutes.

  • Cannabis retailer means any licensed person or entity that purchases or otherwise obtains usable cannabis from cannabis cultivators and cannabis items from cannabis manufacturers or cannabis wholesalers, and sells these to consumers from a retail store, and may use a cannabis delivery service or a certified cannabis handler for the off-premises delivery of cannabis items and related supplies to consumers. A cannabis retailer shall also accept consumer purchases to be fulfilled from its retail store that are presented by a cannabis delivery service which will be delivered by the cannabis delivery service to that consumer.

  • Biodiesel means a fuel composed of mono-alkyl esters of long chain fatty acids derived from vegetable oils or animal fats, and, in accordance with standards specified by the American society for testing and materials, designated B100, and meeting the requirements of D-6751, as approved by the department of agriculture.

  • Supplier Profit means, in relation to a period or a Milestone (as the context requires), the difference between the total Call Off Charges (in nominal cash flow terms but excluding any Deductions) and total Costs (in nominal cash flow terms) for the relevant period or in relation to the relevant Milestone;

  • Bandwidth means a distributor’s defined tolerance used to flag data for further scrutiny at the stage in the VEE process where a current reading is compared to a reading from an equivalent historical billing period. For example, a 30 percent bandwidth means a current reading that is either 30 percent lower or 30 percent higher than the measurement from an equivalent historical billing period will be identified by the VEE process as requiring further scrutiny and verification;

  • High-temperature coating means a high performance coating labeled and formulated for application to substrates exposed continuously or intermittently to temperatures above 204oC (400oF).

  • CMOs means notes or other instruments secured by collateral consisting primarily of mortgages, mortgage-backed securities and/or other types of mortgage-related obligations.

  • EI means annual energy imported excluding Ew and Ef(GJ/year),