Wafers Supplied by RENESOLA. For the polysilicon provided by BP Solar during the term of this agreement, Renesola shall supply wafers to BP Solar at pricing not to exceed the following schedule:
Wafers Supplied by RENESOLA Sample Clauses
Related to Wafers Supplied by RENESOLA
Information Furnished by BISYS BISYS has furnished to the Trust the following:
Clinical Supply Takeda will provide to Licensee[***] the amount of TAK-385 Licensed Compound or TAK-385 Licensed Products needed by Licensee to complete all Clinical Trials contemplated by the TAK-385 Development Plan (estimated by Licensee as of the Effective Date to be [***]), solely to the extent that Takeda can supply such TAK-385 [***] = Portions of this exhibit have been omitted and filed separately with the Securities and Exchange Commission. Confidential treatment requested under 17 C.F.R. Sections 200.80(b)(4) and 230.406. Licensed Compound or TAK-385 Licensed Products (a) from its supply of TAK-385 Licensed Compound or TAK-385 Licensed Products in existence as of the Effective Date and which supply can be used for its intended purposes without further re-processing (the “Initial Clinical Supply”) and (b) after retaining the amount needed by Takeda for Clinical Trials in the Takeda Territory. Takeda will also provide to Licensee, at [***] any additional supplies of TAK-385 Licensed Compound or TAK-385 Licensed Products in excess of the Initial Clinical Supply needed by Licensee to complete all Clinical Trials contemplated by the TAK-385 Development Plan. Within [***] days after the Effective Date, the Parties will enter into a manufacturing and supply agreement (the “Takeda Clinical Manufacturing and Supply Agreement”), which will govern the terms and conditions of the Manufacturing and supply of the TAK-385 Licensed Compound and TAK-385 Licensed Products (including the Initial Clinical Supply) by Takeda to Licensee for Development purposes, including the exact quantities and the timelines for delivery. The Parties will negotiate the terms and conditions of such Takeda Clinical Manufacturing and Supply Agreement in good faith for a period of [***] days (as may be extended upon agreement of the Parties). As part of the negotiation related to the Takeda Clinical Manufacturing and Supply Agreement, the Parties shall discuss in good faith the ability of Takeda to supply to Licensee [***]. If the Parties have not entered into a definitive agreement within such negotiation period, then the final terms and conditions of such agreement will be resolved in accordance with Section 8.2 (Arbitration for Failure to Agree).
Mission Block Fuel The block fuel for a stage length of 2,050 nautical miles in still air (representative of a route with a 4.4 hour flight time from a sea level airport) with a zero fuel weight of 154,221 kilograms, using the conditions and operating rules defined below, shall not be more than the following guarantee value: NOMINAL: [*] Kilograms TOLERANCE: [*] Kilograms GUARANTEE: [*] Kilograms Conditions and operating rules:
Information Furnished by Underwriters Certain statements set forth in the Final Prospectus on the cover page and under the caption “Underwriters” which relate to the terms of the offering of the Securities and to the Underwriters constitute information furnished in writing by you, on behalf of the several Underwriters, for inclusion therein, and you, as the Representatives, confirm that such statements are correct.
Customers; Suppliers Executive does not have, and at any time during the term of this Agreement shall not have, any employment with or any direct or indirect interest in (as owner, partner, shareholder, employee, director, officer, agent, consultant or otherwise) any customer of or supplier to Company.
Information Supplied by Underwriters The statements set forth in the last paragraph on the front cover page and under the heading "Underwriting" in any Preliminary Prospectus or the Prospectus (to the extent such statements relate to the Underwriters) constitute the only information furnished by any Underwriter through the Representatives to the Company for the purposes of Sections 2(b) and 8 hereof. The Underwriters confirm that such statements (to such extent) are correct.
Information Supplied by the Initial Purchasers The statements set forth in the last paragraph under the head- ing "Private Placement" in the Final Memorandum (to the extent such statements relate to the Initial Purchasers) constitute the only information furnished by the Initial Purchasers to the Company for the purposes of Sections 2(a) and 9 hereof.
Supplier Selection If Customer selects a seat or galley supplier that is not on the Boeing recommended list, such seat or galley will become BFE and the provisions of Exhibit A, Buyer Furnished Equipment Provisions Document, of the AGTA will apply.
Compliance with and Liability under Environmental Laws (i) The Company and its subsidiaries (a) are, and at all prior times were, in compliance with any and all applicable federal, state, local and foreign laws, rules, regulations, requirements, decisions, judgments, decrees, orders and the common law relating to pollution or the protection of the environment, natural resources or human health or safety, including those relating to the generation, storage, treatment, use, handling, transportation, Release or threat of Release of Hazardous Materials (collectively, “Environmental Laws”), (b) have received and are in compliance with all permits, licenses, certificates or other authorizations or approvals required of them under applicable Environmental Laws to conduct their respective businesses, (c) have not received notice of any actual or potential liability under or relating to, or actual or potential violation of, any Environmental Laws, including for the investigation or remediation of any Release or threat of Release of Hazardous Materials, and have no knowledge of any event or condition that would reasonably be expected to result in any such notice, (d) are not conducting or paying for, in whole or in part, any investigation, remediation or other corrective action pursuant to any Environmental Law at any location, and (e) are not a party to any order, decree or agreement that imposes any obligation or liability under any Environmental Law, and (ii) there are no costs or liabilities associated with Environmental Laws of or relating to the Company or its subsidiaries, except in the case of each of (i) and (ii) above, for any such matter, as would not, individually or in the aggregate, reasonably be expected to have a Material Adverse Effect; and (iii) except as described in the Registration Statement, the Pricing Disclosure Package and the Prospectus, (a) there are no proceedings that are pending, or that are known to be contemplated, against the Company or any of its subsidiaries under any Environmental Laws in which a governmental entity is also a party, other than such proceedings regarding which it is reasonably believed no monetary sanctions of $100,000 or more will be imposed, (b) the Company and its subsidiaries are not aware of any facts or issues regarding compliance with Environmental Laws, or liabilities or other obligations under Environmental Laws, including the Release or threat of Release of Hazardous Materials, that could reasonably be expected to have a material effect on the capital expenditures, earnings or competitive position of the Company and its subsidiaries, and (c) none of the Company and its subsidiaries anticipates material capital expenditures relating to any Environmental Laws.
Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].
