Vehicle installation Clause Samples
The VEHICLE INSTALLATION clause outlines the requirements and procedures for installing equipment, devices, or systems in a vehicle. It typically specifies who is responsible for performing the installation, the standards or guidelines that must be followed, and any necessary inspections or approvals before the vehicle can be used. This clause ensures that all installations are completed safely and correctly, minimizing risks of malfunction or liability and providing clarity on responsibilities during the installation process.
Vehicle installation. 3.4.1. The vehicle shall be approximately horizontal during the test so as to avoid any abnormal distribution of the fuel.
3.4.2. A current of air of variable speed shall be blown over the vehicle. The blower speed shall be such that, within the operating range of 10 km/h to at least 50 km/h, the linear velocity of the air at the blower outlet is within ±5 km/h of the corresponding roller speed. The final selection of the blower shall have the following characteristics:
(a) Area: at least 0.2 m2;
(b) Height of the lower edge above ground: approximately 0.2 m;
(c) Distance from the front of the vehicle: approximately 0.3 m. As an alternative the blower speed shall be fixed at an air speed of at least 6 m/s (21.6 km/h). For special vehicles (e.g. vans, off-road), the height of the cooling fan can also be modified at the request of the manufacturer.
Vehicle installation. 3.4.1. The vehicle shall be approximately horizontal during the test so as to avoid any abnormal distribution of the fuel.
3.4.2. A current of air of variable speed shall be blown over the vehicle. The blower speed shall be, within the operating range of 10 km/h to at least the maximum speed of the test cycle being used. The linear velocity of the air at the blower outlet shall be within ±5 km/h of the corresponding roller speed within the range of 10 km/h to 50 km/h. At the range over 50 km/h, the linear velocity of the air shall be within ±10 km/h of the corresponding roller speed. At roller speeds of less than 10 km/h, air velocity may be zero. The above mentioned air velocity shall be determined as an averaged value of a number of measuring points which:
(a) For blowers with rectangular outlets are located at the centre of each rectangle dividing the whole of the blower outlet into 9 areas (dividing both horizontal and vertical sides of the blower outlet into 3 equal parts). The centre area shall not be measured (as shown in the diagram below).
(b) For circular blower outlets, the outlet shall be divided into 8 equal arcs by vertical, horizontal and 45° lines. The measurement points lie on the radial centre line of each arc (22.5°) at a radius of two thirds of the total (as shown in the diagram below). These measurements shall be made with no vehicle or other obstruction in front of the fan. The device used to measure the linear velocity of the air shall be located at between 0 and 20 cm from the air outlet. The final selection of the blower shall have the following characteristics:
Vehicle installation. Use the following instructions to install an internal mount transponder to your vehicle. If you have received an internal mount transponder, but need an external bumper mount ▇▇▇▇- ▇▇▇▇▇▇▇ for your vehicle within 90 days from purchase, please contact the LeeWay Service Center at (239) 931–0100 for an exchange. Metallic Windshields Some vehicles have metallic window tinting that interferes with the operation of the internal mount transponder. If you experi- ence problems with your transponder, you may have to switch to a bumper mount transponder.
Vehicle installation. 3.4.1. The vehicle shall be approximately horizontal during the test so as to avoid any abnormal distribution of the fuel.
3.4.2. A current of air of variable speed shall be blown over the vehicle. The blower speed shall be, within the operating range of 10 km/h to at least 50 km/h, or as an alternative, at the request of the manufacturer within the operating range of 10 km/h to at least the maximum speed of the test cycle being used. The linear velocity of the air at the blower outlet shall be within ±5 km/h of the corresponding roller speed within the range of 10 km/h to 50 km/h. At the range over 50 km/h, the linear velocity of the air shall be within ±10 km/h of the corresponding roller speed. At roller speeds of less than 10 km/h, air velocity may be zero. The above mentioned air velocity shall be determined as an averaged value of a number of measuring points which:
(a) For blowers with rectangular outlets are located at the centre of each rectangle dividing the whole of the blower outlet into 9 areas (dividing both horizontal and vertical sides of the blower outlet into 3 equal parts);
(b) For circular blower outlets, the outlet shall be divided into 8 equal arcs by vertical, horizontal and 45° lines. The measurement points lie on the radial centre line of each arc (22.5°) at a radius of two thirds of the total (as shown in the diagram below). Each value at those points shall be within 10 per cent of the averaged value of themselves. The device used to measure the linear velocity of the air shall be located at between 0 and 20 cm from the air outlet. The final selection of the blower shall have the following characteristics:
(i) Area: at least 0.2 m2;
(ii) Height of the lower edge above ground: approximately 0.2 m;
(iii) Distance from the front of the vehicle: approximately 0.3 m. As an alternative, at the request of the manufacturer the blower speed shall be fixed at an air speed of at least 6 m/s (21.6 km/h). The height and lateral position of the cooling fan can also be modified at the request of the manufacturer.
Vehicle installation. The installation of vehicle equipment is the client’s responsibility. This includes, but is not limited to, mobile computers, GPS antennas, docking stations, and modems.
Vehicle installation. The installation of vehicle equipment is the client’s responsibility. This includes, but is not limited to, mobile computers, GPS antennas, docking stations, and modems. Mapping Tyler Public Safety offers 2 options for the configuration of its Mapping product: Basic and Advanced.