Common use of SPECIFICATION TABLES AND DRAWINGS Clause in Contracts

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: 1:1 3/4:1 Curves: As marked on the Solid Rock: 1/4:1 ground Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: 1-1/2:1 Adverse: 8% Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log Maximum tolerance: plus 15% minus 0% DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Curves: Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Switchbacks: Location: at or near the end of all dead end roads as approved by the Forest Officer. Slough widening: (in addition to usable road surface) GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS STREAM CROSSING & WET SITE CULVERT INSTALLATION RUBBER FLAPPER WATER DIVERTERS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: 1:1 3/4:1 Curves: As marked on the Solid Rock: 1/4:1 ground Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: 1-1/2:1 Adverse: 8% Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log Maximum tolerance: plus 15% minus 0% DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Curves: Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Switchbacks: Location: at or near the end of all dead end roads as approved by the Forest Officer. Slough widening: (in addition to usable road surface) GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS ADJUSTABLE GATE – 14’ STEEL CATTLE SPECIFICATIONS HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS CULVERT REQUIREMENTS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible inter-visible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS SWITCHBACK REQUIREMENTS & SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS FILTER FABRIC SEDIMENT CONTROL FENCE RUBBER FLAPPER WATER DIVERTERS OPEN TOP PIPE WATER DIVERTER GATE – 14’ STEEL CATTLE WELDED PIPE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: 1:1 3/4:1 Curves: As marked on the Solid Rock: 1/4:1 ground Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: 1-1/2:1 Adverse: 8% Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log Maximum tolerance: plus 15% minus 0% DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE - SUPERGATE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS SWITCHBACK REQUIREMENTS & SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: 1:1 3/4:1 Curves: As marked on the Solid Rock: 1/4:1 ground Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 15%minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS ADJUSTABLE WARNING SIGN SPECIFICATIONS BRIDGE – TEMP CLT INSTALLATION GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS STREAM CROSSING & WET SITE CULVERT INSTALLATION RUBBER FLAPPER WATER DIVERTERS SWITCHBACK REQUIREMENTS - DRAWING GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS.

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS ADJUSTABLE WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 15% 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base wheelbase 2-wheel-drive pickup. Location: at or near the end of all dead dead- end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS CLEAR LIMITS AND TYPICAL CROSS SECTIONS HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base wheelbase 2-wheel-drive pickup. Location: at or near the end of all dead dead- end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 812% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS.

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW RUBBER FLAPPER WATER DIVERTERS CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS SWITCHBACK REQUIREMENTS & SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: 50 Feet Curves: 50 Feet As marked on the ground Common excavation: 1:1 Angular Rock: 3/4:1 Solid Rock: 1/4:1 Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% Adverse: 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log FILL SLOPE RATIO Common material: 1-1/2:1 Angular rock: 1-1/3:1 Maximum tolerance: plus 15% minus 0% DITCHES TURNOUTS Width: Depth: 3 feet Depth: 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer TURNOUTS Length: 75 feet Width: 7 feet Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: 14 feet Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) Switchbacks: 22 feet Slough widening: Tangents: 1foot (in addition to usable road Curves and all fills surface) over 6 feet height: 2 feet. TURNAROUNDS Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW STREAM CROSSING & WET SITE CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE RUBBER FLAPPER WATER DIVERTERS OPEN TOP PIPE WATER DIVERTER HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS GATE – 14’ STEEL CATTLE RUBBER FLAPPER WATER DIVERTERS HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: 50 Feet Curves: 50 Feet As marked on the ground Common excavation: 1:1 Angular Rock: 3/4:1 Solid Rock: 1/4:1 Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% Adverse: 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log FILL SLOPE RATIO Common material: 1-1/2:1 Angular rock: 1-1/3:1 Maximum tolerance: plus 15% minus 0% DITCHES TURNOUTS Width: Depth: 3 feet Depth: 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer TURNOUTS Length: 75 feet Width: 7 feet Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: 14 feet Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) Switchbacks: 22 feet Slough widening: Tangents: 1foot (in addition to usable road Curves and all fills surface) over 6 feet height: 2 feet. TURNAROUNDS Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS

SPECIFICATION TABLES AND DRAWINGS. GENERAL SPECIFICATIONS GRASS SEEDING SPECIFICATIONS GRAVEL AND END HAUL FILL MATERIAL SPECIFICATIONS CLEAR LIMITS AND TYPICAL CROSS SECTIONS CLEAR LIMIT DEFINITIONS FOR EXISTING ROADS STANDARD DRAIN DIP FOR SINGLE LANE ROAD SLASH FILTER WINDROW CULVERT INSTALLATION REQUIREMENTS ADJUSTABLE GATE – 14’ STEEL CATTLE HIGHWAY SAFETY SIGNS WARNING SIGN SPECIFICATIONS GENERAL SPECIFICATIONS ALIGNMENT CUT SLOPE RATIO Minimum Curve Radius: Switchbacks: Curves: 50 Feet As marked on the ground Common excavation: Angular Rock: Solid Rock: Maximum tolerance: 1:1 3/4:1 1/4:1 plus 15% minus 0% ROAD GRADE MAXIMUM FILL SLOPE RATIO Favorable: Adverse: 12% 8% Common material: Angular rock: Maximum tolerance: 1-1/2:1 1-1/3:1 plus 15% minus 0% Grades as shown in the Road Log DITCHES TURNOUTS Width: Depth: 3 feet 1 foot Length: Width: 75 feet 7 feet Located as shown in the Road Log or as directed by the Forest Officer Located by Purchaser and approved by the Forest Officer. Spacing will be intervisible as topography allows. USABLE ROAD SURFACE TURNAROUNDS Tangents: Curves: Switchbacks: Slough widening: (in addition to usable road surface) 14 feet 16 feet (radius over 75 feet) 20 feet (radius under 75 feet) 22 feet Tangents: 1foot Curves and all fills over 6 feet height: 2 feet. Dimensions: large enough to safely turn around a long wheel base 2-wheel-drive pickup. Location: at or near the end of all dead dead- end roads as approved by the Forest Officer. GRASS SEEDING SPECIFICATIONS