Sealant Clause Samples

Sealant. The sealant shall be used to seal lap joints, bolt connections and sheet edges. The sealant shall cure to a rubber-like consistency and have excellent adhesion to the glass coating, have low shrinkage, and be suitable for interior and exterior exposure. • The sealant shall be a one component moisture cured polyurethane compound. • Where required, the sealant shall be suitable for contact with potable water and meet Regulation 31 or NSF Standard 61 where specified. • EPDM or Neoprene gaskets and tape type sealer shall not be used other than for shell manway door/hatch. • One (1) gallon of sealant applied in the reservoir shall be provided by the Contractor as spare to the Owner.
View SourceView Similar (2)
Sealant. All sealants shall be silicone and resistant to ozone and ultraviolet light and conform to Federal Specification TT-S-00230C.
View Source
Sealant. .1 Internal: selected by curtain wall manufacturer.
View Source
Sealant. Joint sealant and primer shall be polyurethane-based, one component, elastomeric sealants, complying with Fed. Spec. TT-S-00230C, Class A Type 1. Color shall be as selected by the Owner. Sealants shall be self-leveling pour grade type.
View Source
Sealant. .1 Apply sealant in accordance with manufacturer's written instructions.
View Source
Sealant. Special grade of silicon sealant non-hardening, neutral cure type of approved make and grade shall be applied at all side laps and end laps (with flowable mastic) as per manufacturer’s recommendations and approval by Engineer-in-Charge. Sealer for side lap, end laps and self – flashing windows shall be two way self adhesive tapes 6mm wide 5mm thick asbestos fiber filled, pressure sensitive. The sealer shall be non-asphaltic, non-shrinking, non-drying and non-toxic and shall have superior adhesion to metals, plastics and painted surfaces at temperatures from 50 degree to 104 degree centigrade.
View Source
Sealant. Typically, a butyl tape used in the construction of Windows to seal and join the Glass to the Window or door frame.
View Source
Sealant. Silicone sealant with an amine cure system with primer shall be used to waterproof all flashings and rainwater goods, viz. gutters and down pipes. Two runs of silicone shall be provided at end overlaps.
View Source
Sealant. The sealant shall be applied through an applicator manufactured specifically for this purpose. Essentially the equipment for the hot sealant shall consist of a mobile vessel capable of heating the sealant to the required application temperature by indirect heat, controlled by a thermostat to prevent overheating. A calibrated thermometer shall be fitted in an accessible position to accurately measure the sealant temperature in the tank. Special pumps, which can deliver the sealant to the crack in a controlled fashion, shall be used. Proprietary brand seals shall be applied as specified by the suppliers.
View Source

Related to Sealant

  • Ergonomics The supervisor/manager will provide training and equipment for staff to safely perform job functions and avoid injury. Employees should contact their supervisor if job procedures, equipment or workstations lead to risk of injury or work-related musculoskeletal disorders. Further ergonomic guidelines shall be referenced on the Environmental Health and Safety website ▇▇▇.▇▇▇.▇▇▇▇▇▇▇▇▇▇.▇▇▇.

  • Probes Network hosts used to perform (DNS, EPP, etc.) tests (see below) that are located at various global locations.

  • Packaging and Shipping All shipping containers shall be packed and packaged to: (i) ensure safe arrival to final destination; (ii) secure the lowest transportation costs;(iii) comply with requirements of common carriers; (iv) meet Buyer's written instructions; and (v) meet the requirements of all applicable laws, ordinances, rules and regulations.

  • SMT ▇▇▇▇▇ ▇▇▇▇▇▇, (PAN ▇▇▇▇▇▇▇▇▇▇) wife of late ▇▇▇▇▇▇ ▇▇▇▇ ▇▇▇▇▇▇, by faith Hindu, by Nationality Indian, by occupation housewife, (3) ▇▇▇ ▇▇▇▇▇▇▇ ▇▇▇▇▇▇, (PAN ▇▇▇▇▇▇▇▇▇▇) son of late ▇▇▇▇▇▇ ▇▇▇▇ ▇▇▇▇▇▇, by faith Hindu, by Nationality Indian, by occupation service, (4)

  • Safety Glasses Section 1. The City shall supply prescription safety glasses with plastic lenses to employees who are required to wear safety glasses and who are members of the classifications contained in Appendix C to this contract. Safety glasses which are authorized must be industrial grade safety glasses which meet or exceed the requirements of ANSI Specification Z87. 1. All employees who are required to wear safety glasses shall also be required to wear side ▇▇▇▇▇▇▇, either permanent or snap-on, whenever an eye hazard exists. Solid tinted glasses will not be approved unless required by prescription. Photogray, progressive, scratch coating and/or anti-glare lenses may be considered for those employees who primarily work outdoors or as prescribed. In the event that additional classes are identified as needing either prescription safety glasses or protective eyewear, such classes may be added to the classification list in Appendix C upon approval of PAGE and the City. Section 2. The City agrees to pay the full cost of required prescription safety glasses, with frames not to exceed $75.00. This excludes the cost of the eye examination which will be the responsibility of the employee. The effected employees will be allowed one (1) replacement of safety glasses every two (2) years. In the event the safety glasses become lost, unserviceable, or broken on the job, the employee must present a written request for replacement to the Department Head and Human Resources Director. If the employee breaks his safety glasses while on the job, the Department shall replace the glasses at no cost to the employee. The replacement of lost glasses or glasses that are broken off the job will be at the discretion of the Department Head and Human Resources Director. If an employee has been provided safety glasses by the City, the employee shall be permitted to retain possession of the glasses after separation from the City without reimbursing the City for any costs associated with the glasses. Section 3. An employee who is required to wear prescription safety glasses must present a written request to his department head or designated representative. Section 4. The employee must obtain a current prescription and the employee is authorized the use of sick leave not to exceed two (2) hours to accomplish this examination. The employee will obtain a purchase order from the Department Head prior to ordering the safety glasses. The employee will present the purchase order to the appropriate vendor when ordering. The vendor will contact the appropriate Department Head when the glasses are ready for delivery. The Department Head will then notify the employee who will present himself at the vendor for fitting and pickup. Section 5. In the event a probationary employee has been issued safety glasses and terminates his employment with the City for any reason during the probationary period, he shall be required to reimburse the City for any expenses incurred in the purchase of safety glasses.