Common use of Normal Duties Clause in Contracts

Normal Duties. Develop full-size and/or scale lines layouts for tooling purposes, using standard lofting practices and analytical approaches. Develop and check loft calculations and mathematical equations defining various surfaces to be lofted utilizing a broad knowledge of algebra, trigonometry and analytic geometry. TOOL DESIGNER A JOB CODE: 1204 Job Requirement: Requires 8 years of training and experience including 3 years of College Engineering or equivalent, and 5 years of experience in tool designing. Must be fully familiar with Tool Room practices and procedures. Normal Duties: Design conventional and non-conventionl complex tools including tooling masters, machine tools, test equipment, and special purpose machines from tooling requirement information received from Planning or Tool Engineering. Develop design for the required tools. Prepare or direct the preparation of detail drawings and perform all necessary calculations required for fabrication of tools. Design modifications on existing complex tools from outline of modification requirements furnished by such sources as Engineering or Supervision. Prepare or direct the preparation of detail working drawings. Advise on the development of a new part or assembly design and recommend changes to the design so as to facilitate the manufacturing processes utilizing existing tooling and equipment wherever possible. TOOL STANDARDS WRITER JOB CODE: 1206 Job Requirement: Requires 5 years' experience in writing Tool Standards and specifications. Have good working knowledge of heat treatments, finishes, materials, general tooling and shop equipment and be capable of investigating problems connected with these categories as it applies to tooling in the aerospace industry. Be acquainted with and capable of interpreting government specifications and standards. The ability to read a variety of instructions, specifications and standards on specific subjects and compile the pertinent data into clear, grammatical and concise instructions. Normal Duties: Investigate existing and new tooling techniques, determine best procedure to be followed and determine additional equipment if required. Is required to establish a method of carrying out tool procedure, including requirements for Inspection and Quality Control. Determine and lay down materials and equipment required for carrying out the standards, also procurement sources for ordering purposes. Prepare drawings and sketches for clarification of instructions. Plan and write up a complete tool standard in correct operational sequence. Carry out investigations into problems on tooling procedures. Recommend changes in tooling techniques to facilitate same. Supply technical information and advice regarding materials, finishes, treatments and techniques as it applies to tooling standards. Carry out duties with minimum of instruction and supervision. QUALITY ASSURANCE OFFICER JOB CODE: 1209 Job Requirement: A minimum of five (5) years' experience in Inspection, Manufacturing, Planning or engineering activity, at least two (2) of which have been in the aerospace industry.

Normal Duties. Develop fullResponsible for preparation of Quality Assurance processes, procedures and standards to determine inspection methods, techniques, facility needs and frequency of application of non-size destructive, destructive, dimensional, functional and environmental studies. Analyze the planning of detail parts, assemblies and kits to ensure that all Engineering and Quality Assurance processes, procedures and standards are properly called out. Review and co-ordinate to ensure that Engineering changes (specifications, E.O.'s, etc.) have been incorporated into assemblies and aircraft at proper effectivity. Determine the cause of production or sub-contract quality problems and prepare and/or scale lines layouts make recommendations for tooling purposescorrective action. Prepare necessary reports, using standard lofting practices review relative Purchase Orders for proper wording and analytical approachesact in a liaison capacity with customers and inter-component divisions by answering queries and co-ordinating related internal activities. Develop and check loft calculations and mathematical equations defining various surfaces Give technical direction to be lofted utilizing a broad knowledge of algebra, trigonometry and analytic geometrylower classified employees working cooperatively on Quality Assurance problems. Perform other related duties as required. TOOL DESIGNER A ENGINEER JOB CODE: 1204 1210 Job Requirement: Requires 8 six (6) years of training and experience including 3 three (3) years of College college Engineering or equivalent, equivalent and 5 three (3) years of experience in tool designing. Must be fully familiar with Tool Room practices and proceduresdesign or equivalent. Normal Duties: Design conventional and non-conventionl complex tools including tooling masters, machine tools, test equipment, and special purpose machines from tooling requirement information received from Planning or Tool Engineering. Develop design for the required tools. Prepare or direct the preparation of detail drawings and perform all necessary calculations required for fabrication of tools. Design modifications on existing complex tools from outline of modification requirements furnished by such sources as Engineering or Supervision. Prepare or direct the preparation of detail working drawings. Advise on the development of a new part or assembly design Review and recommend changes to on conventional and complex preliminary tool plans, prepared concurrently with the product design, for practicability and manufacturing and assembly sequence. Supply basic concepts of tooling information for components of the product. As directed establish requirements for the design so of special power machine tools and attachments, or prepare information and data for tool design to adapt an existing or obsolete standard machine tool into a universal use tool or to perform a specialized function. Coordinate, develop and conduct fabrication tests on standard structural parts. When requested act as a functional consultant with related classifications on tooling problems in assigned field, such as recommending changes in engineering designs for simplification or improvement of a tool design, co- ordinating engineering standards and standard tooling, working with salvage on the disposition of tooling parts. Originate and direct the design concepts of new tooling or tooling methods and related applications of original ideas to facilitate simplify existing methods, reduce design, manufacturing and operating time and costs or utilize new materials for tooling applications. In the manufacturing processes utilizing existing tooling performance of the above named duties, originate the necessary documents and equipment wherever possiblereports, used to transmit and plan technical information to Tool Design, Planning and Tool Liaison within the Company's systems and procedures under the direction of senior personnel. TOOL STANDARDS WRITER NUMERICAL CONTROL PARTS PROGRAMMER A JOB CODE: 1206 1211 Job Requirement: Requires 5 years' experience in writing Tool Standards and specifications. Have good working knowledge of heat treatments, finishes, materials, general tooling and shop equipment and be capable of investigating problems connected with these categories as it applies to tooling in the aerospace industry. Be acquainted with and capable of interpreting government specifications and standards. The ability to read a variety of instructions, specifications and standards on specific subjects and compile the pertinent data into clear, grammatical and concise instructions. Normal Duties: Investigate existing and new tooling techniques, determine best procedure to be followed and determine additional equipment if required. Is required to establish a method of carrying out tool procedure, including requirements for Inspection and Quality Control. Determine and lay down materials and equipment required for carrying out the standards, also procurement sources for ordering purposes. Prepare drawings and sketches for clarification of instructions. Plan and write up a complete tool standard in correct operational sequence. Carry out investigations into problems on tooling procedures. Recommend changes in tooling techniques to facilitate same. Supply technical information and advice regarding materials, finishes, treatments and techniques as it applies to tooling standards. Carry out duties with minimum of instruction and supervision. QUALITY ASSURANCE OFFICER JOB CODE: 1209 Job Requirement: A minimum of five (5) years' experience in Inspection, Manufacturing, Planning or engineering activity, at least including two (2) years of which have been college mathematics in analytical geometry and mathematical surface development. Fundamental knowledge of Manufacturing Engineering practices related to the aerospace industrymachining of aircraft components, thorough understanding of numerical control machines, their capabilities and limitations. Must be thoroughly conversant with A.P.T. language, complex aircraft drawings, graphics and other computer aided systems related to N/C Programming. Normal Duties: Prepares numerical control programs to machine complex aircraft components including five (5) or more axis.

Normal Duties. Develop full-size and/or scale lines Investigate and solve problems relating to the design of all electronic controls on machines and equipment throughout the facility, developing satisfactory solutions. Design and prepare drawings for complex and less complex facilities electronic requirements from information provided and carry out any further investigation of detail measurement, selection of materials on equipment items, or calculations as required to complete the drawings. When necessary coordinate with other facilities design draftspersons to ensure the accurate plant layouts for tooling purposesas they relate to electronic requirements. To assist in the accomplishment of the above, using standard lofting practices carry out necessary survey of plant areas, discussing requirements with user groups, and analytical approachesdeveloping methods of providing the facility required. Develop and check loft calculations and mathematical equations defining various surfaces Also carry out calculations, selecting special equipment items to be lofted utilizing used, preparing specifications, bills of material and drawings as necessary. As required, prepare detailed estimates, specifications and scope of work for procurement department functions, bid analysis on a broad knowledge technical and cost comparison basis and recommend choice of algebra, trigonometry contractor. As directed coordinate and analytic geometrymonitor the work and progress of the sub-contracting agency. TOOL DESIGNER A SENIOR QUALITY ASSURANCE PROGRAMMER JOB CODE: 1204 Job Requirement: Requires 8 years of training and experience including 3 years of College Engineering or equivalent, and 5 years of experience in tool designing. Must be fully familiar with Tool Room practices and procedures. Normal Duties: Design conventional and non-conventionl complex tools including tooling masters, machine tools, test equipment, and special purpose machines from tooling requirement information received from Planning or Tool Engineering. Develop design for the required tools. Prepare or direct the preparation of detail drawings and perform all necessary calculations required for fabrication of tools. Design modifications on existing complex tools from outline of modification requirements furnished by such sources as Engineering or Supervision. Prepare or direct the preparation of detail working drawings. Advise on the development of a new part or assembly design and recommend changes to the design so as to facilitate the manufacturing processes utilizing existing tooling and equipment wherever possible. TOOL STANDARDS WRITER JOB CODE: 1206 Job Requirement: Requires 5 years' experience in writing Tool Standards and specifications. Have good working knowledge of heat treatments, finishes, materials, general tooling and shop equipment and be capable of investigating problems connected with these categories as it applies to tooling in the aerospace industry. Be acquainted with and capable of interpreting government specifications and standards. The ability to read a variety of instructions, specifications and standards on specific subjects and compile the pertinent data into clear, grammatical and concise instructions. Normal Duties: Investigate existing and new tooling techniques, determine best procedure to be followed and determine additional equipment if required. Is required to establish a method of carrying out tool procedure, including requirements for Inspection and Quality Control. Determine and lay down materials and equipment required for carrying out the standards, also procurement sources for ordering purposes. Prepare drawings and sketches for clarification of instructions. Plan and write up a complete tool standard in correct operational sequence. Carry out investigations into problems on tooling procedures. Recommend changes in tooling techniques to facilitate same. Supply technical information and advice regarding materials, finishes, treatments and techniques as it applies to tooling standards. Carry out duties with minimum of instruction and supervision. QUALITY ASSURANCE OFFICER JOB CODE: 1209 1221 Job Requirement: A minimum of five years experience in machine shop inspection/tooling inspection or engineering activity, at least two years of which were in the Aerospace Industry. Must be a sight reader of complex aircraft and/or tooling drawings. Must have three years of college mathematics including studies in matrices, vectors, and metrology. Must be proficient in "Analytic Geometry" and mathematical surface development. Must be proficient in the use of co-ordinate measuring machines (CMM) and two or more numerical control languages. Normal Duties: Analyse complex engineering drawings/specifications and changes to develop Machine Parts Inspection Plan Procedures. Prepare and maintain numerical control tapes used by Quality Assurance Personnel to check masters, tools, parts and components, and develop programs to establish co-ordinate inspection points for checking lofted contours and engineering dimensions, using the computer aided Quality Assurance Module or CMM and ancilliary equipment to prove tape. Access host computer data for construction of Quality Assurance Programs and verification of Manufacturing data. Carry out any assignment or corrective action investigation. QUALITY ASSURANCE SOURCE REPRESENTATIVE JOB CODE: 1222 Job Requirement: A minimum of four (4) years of experience in one or more of the following activities: inspection, manufacturing, planning or engineering, including at least two (2) years of inspection experience in the aerospace industry. Normal Duties: Responsible for ensuring that drawing and specifications requirements indicated on purchase orders are met by checking dimensional requirements, monitoring vendors' dimensional checks for first-off items, verifying rework as defined by the Material Review Board and following-up to eliminate any possible discrepancies or inaccuracies in future shipments. Ensures that raw materials meet specifications by checking that MDCAN material is used where specified or that other incoming material to the vendor plant has had the proper checks to ensure that it meets specification requirements. Performs surveillance of vendors' procedures, including pertinent process paper and other records to ensure that all quality checks are performed and that specifications are met. Performs sample checking of dimensions on manufactured items and makes periodic checks of assemblies as they progress through the vendors' manufacturing process. Provides a liaison function between MDCAN and vendor and/or subcontractors by advising them about MDCAN requirements; Acts as an MDCAN problem-solving resourceperson for vendors by making recommendations for corrective action and/or improvements. Liaises with the MDCAN departments involved to assist in the implementation of their recommendations. Spot checks parts and ensures that finish requirements are met. Checks Release Notes and all other documentation relative to shipment. Advises MDCAN supervision that all requirements have been met and requests approval to release vendor shipments to MDCAN. SENIOR MANUFACTURING PLANNER JOB CODE: 1223 Job Requirement: Apprenticeship in the engineering field, machine shop/toolroom or equivalent experience and five (5) years' experience in Inspectiona production engineering office. A thorough knowledge of engineering, Manufacturingtooling and lofted drawings and associated documents, Planning and the ability to prepare job related graphs and fully dimensioned sketches, including tooling sketches and understanding and applying manufacturing processes. Be fully conversant with all in-plant machinery related to the classification and have a knowledge of relevant machinery available on the market. Ability to work with sub-contractors and personnel of other departments in efforts to resolve all job related problems. Works with minimum direction and without supervision. Normal Duties: Determine and order the tooling and materials required to produce details, simple to complex machined parts (*), sub assemblies and assemblies other than machined parts. Plan and write up the manufacturing operations required, using the best/most economical methods, supplying standard operation times to fabrication orders and following assignments through by ensuring that technical direction is given on all phases of the work. Action changes to previously designed and processed products, including reworks. Investigate manufacturing and tooling problems, making changes to fabrication orders, tool orders, raising tooling sketches, other planning documents to overcome delays and/or plan and write up corrective action necessary to resolve such problems. When required give technical assistance to Junior Planners and instruct on the handling of routine paperwork and basic planning methods. *Machined Parts - are those produced on machines or engineering activityequipment commonly recognized in the industry as machine shop equipment for milling, turning boring, heavy duty router etc. Analyze new products from complete design package through to detail parts and working in conjunction with master policy directives, programme planning and tooling activity of details, machined parts sub assemblies, assemblies and major assemblies. Direct, coordinate the efforts of, and check the work of junior planners (job code 916). Field of activity to embrace planning and tooling of details, machined parts sub assemblies, assemblies and major assemblies, and in conjunction with master policy directives, establish master coordination of tooling to ensure interchangeability of parts. Follow through planning assignments, supplying technical direction to sub-contractors, manufacturing and tooling departments and in conjunction with personnel of these agencies make "on the spot" decisions. Give guidance to junior planners (job code 916). LABORATORY TECHNOLOGIST JOB CODE 1224 Job Requirement: 2004 Must have minimum experience of five (5) years at least a Metallurgical and/or Chemical Technician level of responsibility and qualification to one of the following standards: Diploma from an Ontario Institute of Technology or Ordinary National Certificate (U.K.) or equivalent with a minimum of two (2) years' relevant experience in an industrial chemical and/or metallurgical laboratory. OR A suitable course of which part-time study in chemistry and/or metalurgy of a level equal to that of an Ontario Advanced Evening Class Certificate, 2nd level, with a minimum of three (3) years' relevant experience in an industrial chemistry and/or metallurgical laboratory. In addition, must have been in indicated a high level of initiative and resourcefulness. Normal Duties: Conduct all aspects of an assigned chemical and metallurgical testing program, from planning to reporting. Assess the aerospace industrysignificance of all test results and make suitable recommendations. Calibrate instrumentation and equipment, manufacture thermocouples and operate potentiometers, voltmeters, ammeters and similar instruments. Prepare clear and concise technical reports, including non-routine reports. Work with guidance but with a minimum of supervision, and instruct personnel of lower classifications.

Normal Duties. Develop full-size and/or scale lines Investigate and solve problems relating to the design of all electronic controls on machines and equipment throughout the facility, developing satisfactory solutions. Design and prepare drawings for complex and less complex facilities electronic requirements from information provided and carry out any further investigation of detail measurement, selection of materials on equipment items, or calculations as required to complete the drawings. When necessary coordinate with other facilities design draftspersons to ensure the accurate plant layouts for tooling purposesas they relate to electronic requirements. To assist in the accomplishment of the above, using standard lofting practices carry out necessary survey of plant areas, discussing requirements with user groups, and analytical approachesdeveloping methods of providing the facility required. Develop and check loft calculations and mathematical equations defining various surfaces Also carry out calculations, selecting special equipment items to be lofted utilizing used, preparing specifications, bills of material and drawings as necessary. As required, prepare detailed estimates, specifications and scope of work for procurement department functions, bid analysis on a broad knowledge technical and cost comparison basis and recommend choice of algebra, trigonometry contractor. As directed coordinate and analytic geometrymonitor the work and progress of the sub-contracting agency. TOOL DESIGNER A SENIOR QUALITY ASSURANCE PROGRAMMER JOB CODE: 1204 Job Requirement: Requires 8 years of training and experience including 3 years of College Engineering or equivalent, and 5 years of experience in tool designing. Must be fully familiar with Tool Room practices and procedures. Normal Duties: Design conventional and non-conventionl complex tools including tooling masters, machine tools, test equipment, and special purpose machines from tooling requirement information received from Planning or Tool Engineering. Develop design for the required tools. Prepare or direct the preparation of detail drawings and perform all necessary calculations required for fabrication of tools. Design modifications on existing complex tools from outline of modification requirements furnished by such sources as Engineering or Supervision. Prepare or direct the preparation of detail working drawings. Advise on the development of a new part or assembly design and recommend changes to the design so as to facilitate the manufacturing processes utilizing existing tooling and equipment wherever possible. TOOL STANDARDS WRITER JOB CODE: 1206 Job Requirement: Requires 5 years' experience in writing Tool Standards and specifications. Have good working knowledge of heat treatments, finishes, materials, general tooling and shop equipment and be capable of investigating problems connected with these categories as it applies to tooling in the aerospace industry. Be acquainted with and capable of interpreting government specifications and standards. The ability to read a variety of instructions, specifications and standards on specific subjects and compile the pertinent data into clear, grammatical and concise instructions. Normal Duties: Investigate existing and new tooling techniques, determine best procedure to be followed and determine additional equipment if required. Is required to establish a method of carrying out tool procedure, including requirements for Inspection and Quality Control. Determine and lay down materials and equipment required for carrying out the standards, also procurement sources for ordering purposes. Prepare drawings and sketches for clarification of instructions. Plan and write up a complete tool standard in correct operational sequence. Carry out investigations into problems on tooling procedures. Recommend changes in tooling techniques to facilitate same. Supply technical information and advice regarding materials, finishes, treatments and techniques as it applies to tooling standards. Carry out duties with minimum of instruction and supervision. QUALITY ASSURANCE OFFICER JOB CODE: 1209 1221 Job Requirement: A minimum of five years experience in machine shop inspection/tooling inspection or engineering activity, at least two years of which were in the Aerospace Industry. Must be a sight reader of complex aircraft and/or tooling drawings. Must have three years of college mathematics including studies in matrices, vectors, and metrology. Must be proficient in "Analytic Geometry" and mathematical surface development. Must be proficient in the use of co-ordinate measuring machines (CMM) and two or more numerical control languages. Normal Duties: Analyse complex engineering drawings/specifications and changes to develop Machine Parts Inspection Plan Procedures. Prepare and maintain numerical control tapes used by Quality Assurance Personnel to check masters, tools, parts and components, and develop programs to establish co-ordinate inspection points for checking lofted contours and engineering dimensions, using the computer aided Quality Assurance Module or CMM and ancilliary equipment to prove tape. Access host computer data for construction of Quality Assurance Programs and verification of Manufacturing data. Carry out any assignment or corrective action investigation. QUALITY ASSURANCE SOURCE REPRESENTATIVE JOB CODE: 1222 Job Requirement: A minimum of four (4) years of experience in one or more of the following activities: inspection, manufacturing, planning or engineering, including at least two (2) years of inspection experience in the aerospace industry. Normal Duties: Responsible for ensuring that drawing and specifications requirements indicated on purchase orders are met by checking dimensional requirements, monitoring vendors' dimensional checks for first-off items, verifying rework as defined by the Material Review Board and following-up to eliminate any possible discrepancies or inaccuracies in future shipments. Ensures that raw materials meet specifications by checking that MDCAN material is used where specified or that other incoming material to the vendor plant has had the proper checks to ensure that it meets specification requirements. Performs surveillance of vendors' procedures, including pertinent process paper and other records to ensure that all quality checks are performed and that specifications are met. Performs sample checking of dimensions on manufactured items and makes periodic checks of assemblies as they progress through the vendors' manufacturing process. Provides a liaison function between MDCAN and vendor and/or subcontractors by advising them about MDCAN requirements; Acts as an MDCAN problem-solving resourceperson for vendors by making recommendations for corrective action and/or improvements. Liaises with the MDCAN departments involved to assist in the implementation of their recommendations. Spot checks parts and ensures that finish requirements are met. Checks Release Notes and all other documentation relative to shipment. Advises MDCAN supervision that all requirements have been met and requests approval to release vendor shipments to MDCAN. SENIOR MANUFACTURING PLANNER JOB CODE: 1223 Job Requirement: Apprenticeship in the engineering field, machine shop/toolroom or equivalent experience and five (5) years' experience in Inspectiona production engineering office. A thorough knowledge of engineering, Manufacturingtooling and lofted drawings and associated documents, Planning and the ability to prepare job related graphs and fully dimensioned sketches, including tooling sketches and understanding and applying manufacturing processes. Be fully conversant with all in-plant machinery related to the classification and have a knowledge of relevant machinery available on the market. Ability to work with sub-contractors and personnel of other departments in efforts to resolve all job related problems. Works with minimum direction and without supervision. Normal Duties: Determine and order the tooling and materials required to produce details, simple to complex machined parts (*), sub assemblies and assemblies other than machined parts. Plan and write up the manufacturing operations required, using the best/most economical methods, supplying standard operation times to fabrication orders and following assignments through by ensuring that technical direction is given on all phases of the work. Action changes to previously designed and processed products, including reworks. Investigate manufacturing and tooling problems, making changes to fabrication orders, tool orders, raising tooling sketches, other planning documents to overcome delays and/or plan and write up corrective action necessary to resolve such problems. When required give technical assistance to Junior Planners and instruct on the handling of routine paperwork and basic planning methods. *Machined Parts - are those produced on machines or engineering activity, at least two (2) of which have been equipment commonly recognized in the aerospace industryindustry as machine shop equipment for milling, turning boring, heavy duty router etc. Analyze new products from complete design package through to detail parts and working in conjunction with master policy directives, programme planning and tooling activity of details, machined parts sub assemblies, assemblies and major assemblies. Direct, coordinate the efforts of, and check the work of junior planners (job code 916). Field of activity to embrace planning and tooling of details, machined parts sub assemblies, assemblies and major assemblies, and in conjunction with master policy directives, establish master coordination of tooling to ensure interchangeability of parts. Follow through planning assignments, supplying technical direction to sub-contractors, manufacturing and tooling departments and in conjunction with personnel of these agencies make "on the spot" decisions. Give guidance to junior planners (job code 916).

Normal Duties. Develop fullResponsible for preparation of Quality Assurance processes, procedures and standards to determine inspection methods, techniques, facility needs and frequency of application of non-size destructive, destructive, dimensional, functional and environmental studies. Analyze the planning of detail parts, assemblies and kits to ensure that all Engineering and Quality Assurance processes, procedures and standards are properly called out. Review and co-ordinate to ensure that Engineering changes (specifications, E.O.'s, etc.) have been incorporated into assemblies and aircraft at proper effectivity. Determine the cause of production or sub-contract quality problems and prepare and/or scale lines layouts make recommendations for tooling purposescorrective action. Prepare necessary reports, using standard lofting practices review relative Purchase Orders for proper wording and analytical approachesact in a liaison capacity with customers and inter-component divisions by answering queries and co-ordinating related internal activities. Develop and check loft calculations and mathematical equations defining various surfaces Give technical direction to be lofted utilizing a broad knowledge of algebra, trigonometry and analytic geometrylower classified employees working cooperatively on Quality Assurance problems. Perform other related duties as required. TOOL DESIGNER A ENGINEER JOB CODE: 1204 1210 Job Requirement: Requires 8 six (6) years of training and experience including 3 three (3) years of College college Engineering or equivalent, equivalent and 5 three (3) years of experience in tool designing. Must be fully familiar with Tool Room practices and proceduresdesign or equivalent. Normal Duties: Design conventional and non-conventionl complex tools including tooling masters, machine tools, test equipment, and special purpose machines from tooling requirement information received from Planning or Tool Engineering. Develop design for the required tools. Prepare or direct the preparation of detail drawings and perform all necessary calculations required for fabrication of tools. Design modifications on existing complex tools from outline of modification requirements furnished by such sources as Engineering or Supervision. Prepare or direct the preparation of detail working drawings. Advise on the development of a new part or assembly design Review and recommend changes to on conventional and complex preliminary tool plans, prepared concurrently with the product design, for practicability and manufacturing and assembly sequence. Supply basic concepts of tooling information for components of the product. As directed establish requirements for the design so of special power machine tools and attachments, or prepare information and data for tool design to adapt an existing or obsolete standard machine tool into a universal use tool or to perform a specialized function. Coordinate, develop and conduct fabrication tests on standard structural parts. When requested act as a functional consultant with related classifications on tooling problems in assigned field, such as recommending changes in engineering designs for simplification or improvement of a tool design, co-ordinating engineering standards and standard tooling, working with salvage on the disposition of tooling parts. Originate and direct the design concepts of new tooling or tooling methods and related applications of original ideas to facilitate simplify existing methods, reduce design, manufacturing and operating time and costs or utilize new materials for tooling applications. In the manufacturing processes utilizing existing tooling performance of the above named duties, originate the necessary documents and equipment wherever possiblereports, used to transmit and plan technical information to Tool Design, Planning and Tool Liaison within the Company's systems and procedures under the direction of senior personnel. TOOL STANDARDS WRITER NUMERICAL CONTROL PARTS PROGRAMMER A JOB CODE: 1206 1211 Job Requirement: Requires 5 years' experience in writing Tool Standards and specifications. Have good working knowledge of heat treatments, finishes, materials, general tooling and shop equipment and be capable of investigating problems connected with these categories as it applies to tooling in the aerospace industry. Be acquainted with and capable of interpreting government specifications and standards. The ability to read a variety of instructions, specifications and standards on specific subjects and compile the pertinent data into clear, grammatical and concise instructions. Normal Duties: Investigate existing and new tooling techniques, determine best procedure to be followed and determine additional equipment if required. Is required to establish a method of carrying out tool procedure, including requirements for Inspection and Quality Control. Determine and lay down materials and equipment required for carrying out the standards, also procurement sources for ordering purposes. Prepare drawings and sketches for clarification of instructions. Plan and write up a complete tool standard in correct operational sequence. Carry out investigations into problems on tooling procedures. Recommend changes in tooling techniques to facilitate same. Supply technical information and advice regarding materials, finishes, treatments and techniques as it applies to tooling standards. Carry out duties with minimum of instruction and supervision. QUALITY ASSURANCE OFFICER JOB CODE: 1209 Job Requirement: A minimum of five (5) years' experience in Inspection, Manufacturing, Planning or engineering activity, at least including two (2) years of which have been college mathematics in analytical geometry and mathematical surface development. Fundamental knowledge of Manufacturing Engineering practices related to the aerospace industrymachining of aircraft components, thorough understanding of numerical control machines, their capabilities and limitations. Must be thoroughly conversant with A.P.T. language, complex aircraft drawings, graphics and other computer aided systems related to N/C Programming. Normal Duties: Prepares numerical control programs to machine complex aircraft components including five (5) or more axis.