Grade Control Sample Clauses

Grade Control. PLAN shall mean a plan for the purpose of controlling the overall drainage pattern through the establishment of relative surface elevations in accordance with good engineering and drainage practices.
AutoNDA by SimpleDocs
Grade Control. During construction, the lines and grades including crown and cross slope indicated for the base course shall be maintained by means of line and grade stakes placed by the Contractor. Base courses shall be placed when the atmospheric temperature is above 2 degrees C (36 F). Areas of completed base course that are damaged by freezing, rainfall, or other weather conditions shall be corrected to meet specified requirement. The coarse and fine aggregates shall be mixed in a stationary plant. Water shall also be added to the aggregate prior to placement at a stationary mixing plant. The amount of water added shall be considerably above optimum moisture. The Contractor shall make such adjustments in mixing procedures or in equipment as may be directed to obtain true grades, to minimize segregation or degradation, to obtain the required water content, and to insure a satisfactory base course meeting all requirements of this specification. The mixed material shall be placed on the prepared sub-grade or sub-base in layers of uniform thickness with an approved spreader box when possible as directed by City Engineer. Tracked equipment operated on base course material shall have street tracks. When a compacted layer 150 mm (6 inches) or less in thickness is required, the material shall be placed in a single layer. When a compacted layer in excess of 150 mm (6 inches) is required, the material shall be placed in layers of equal thickness. No layer shall exceed 150 mm (6 inches) or be less than 75 mm (3 inches) when compacted. The layers shall be so placed that when compacted they will be true to the grades or levels required with the least possible surface disturbance. Where the base course is placed in more than one layer, the previously constructed layers shall be cleaned of loose and foreign matter by sweeping with power sweepers, power brooms, or hand brooms, as directed. Such adjustments in placing procedures or equipment shall be made as may be directed to obtain true grades, to minimize segregation and degradation, to adjust the water content, content, and to insure an acceptable base course. Mixed material shall not be placed on or above frozen material.
Grade Control. Achieve grade control by use of 1 or more of the following grade reference devices. Approval of any of these devices will be based upon satisfactory performance.
Grade Control. Establish and maintain the required lines and grades, including crown and cross-slope, for each course during construction operations.
Grade Control. Establish and maintain required lines and elevations.

Related to Grade Control

  • TRADE CONTROL COMPLIANCE a. The Parties shall comply with all export and import laws, regulations, decrees, orders, and policies of the United States Government and the Government of any country in which the Parties conduct business pursuant to this Contract, including but not limited to the Export Administration Regulations (“EAR”) of the U.S. Department of Commerce, the International Traffic in Arms Regulations (“ITAR”) of the U.S. Department of State, the U.S. Customs & Border Protection Regulations, the Harmonized Tariff Schedule, and the antiboycott and embargo regulations and guidelines as set forth in the EAR and in the U.S. Department of the Treasury, Office of Foreign Assets Control (collectively, “Trade Control Laws”).

  • Trade Contractor A Subcontractor who furnishes and installs materials according to the plans and specifications of this Project but does not include one who merely furnishes materials. See 1.1.9.49.

  • Trade Controls DXC and Supplier will comply with all applicable export, import and trade-related laws and regulations of the United States and other nations. To this effect, Supplier warrants that: (i) if necessary and upon DXC’s request, it will provide DXC with technical specifications concerning commodities, software, technology or services covered by this agreement sufficient for DXC to determine the appropriate export and import classification of such items under applicable regulations; (ii) to the best of the Supplier’s knowledge, the Supplier is not listed on any U.S. Government international trade sanctions lists and that Supplier will give immediate notice to DXC in the event that it is so listed; and

  • Infection Control Consistent with the Centers for Disease Control and Prevention Guideline for Infection Control in Health Care Personnel, and University Policy 3364-109-EH-603, the parties agree that all bargaining unit employees who come in contact with patients in the hospital or ambulatory care clinics will need to be vaccinated against influenza when flu season begins each fall. The influenza vaccine will be offered to all health care workers, including pregnant women, before the influenza season, unless otherwise medically contraindicated or it compromises sincerely held religious beliefs.

  • Erosion Control a. The Purchaser shall construct slash and debris erosion barriers, dips, water bars or ditches in skid trails and landings as directed by the Forest Officer.

  • Quality Control A. Controlled Affiliate agrees to use the Licensed Marks and Name only in connection with the licensed services and further agrees to be bound by the conditions regarding quality control shown in attached Exhibit A as they may be amended by BCBSA from time-to-time.

  • STATEWIDE CONTRACT MANAGEMENT SYSTEM If the maximum amount payable to Contractor under this Contract is $100,000 or greater, either on the Effective Date or at any time thereafter, this section shall apply. Contractor agrees to be governed by and comply with the provisions of §§00-000-000, 00-000-000, 00-000-000, and 00- 000-000, C.R.S. regarding the monitoring of vendor performance and the reporting of contract information in the State’s contract management system (“Contract Management System” or “CMS”). Contractor’s performance shall be subject to evaluation and review in accordance with the terms and conditions of this Contract, Colorado statutes governing CMS, and State Fiscal Rules and State Controller policies.

  • Pollution Control The Employer and the Union agree to limit all forms of environmental pollution.

  • Fraud Control BellSouth will provide seven days per week, 24-hours per day, fraud monitoring on Calling Cards, xxxx-to-third and collect calls made to numbers in BellSouth’s LIDB, provided that such information is included in the LIDB query. BellSouth will establish fraud alert thresholds and will notify <<customer_name>> of fraud alerts so that <<customer_name>> may take action it deems appropriate.

  • Site Control In the total loss of building use scenario, what likely exists will be a smoking pile of rubble. This rubble will contain many components that could be dangerous. It could also contain any personnel on the premises at the time of the disaster. For these reasons, the local fire marshal with the assistance of the police will control the site until the building is no longer a threat to surrounding properties and the companies have secured the site from the general public. During this time, the majority owner of the building should be arranging for a demolition contractor to mobilize to the site with the primary objective of reaching the cable entrance facility for a damage assessment. The results of this assessment would then dictate immediate plans for restoration, both short term and permanent. In a less catastrophic event, i.e., the building is still standing and the cable entrance facility is usable, the situation is more complex. The site will initially be controlled by local authorities until the threat to adjacent property has diminished. Once the site is returned to the control of the companies, the following events should occur. An initial assessment of the main building infrastructure systems (mechanical, electrical, fire and life safety, elevators, and others) will establish building needs. Once these needs are determined, the majority owner should lead the building restoration efforts. There may be situations where the site will not be totally restored within the confines of the building. The companies must individually determine their needs and jointly assess the cost of permanent restoration to determine the overall plan of action. Multiple restoration trailers from each company will result in the need for designated space and installation order. This layout and control is required to maximize the amount of restoration equipment that can be placed at the site, and the priority of placements. Care must be taken in this planning to ensure other restoration efforts have logistical access to the building. Major components of telephone and building equipment will need to be removed and replaced. A priority for this equipment must also be jointly established to facilitate overall site restoration. (Example: If the AC switchgear has sustained damage, this would be of the highest priority in order to regain power, lighting, and HVAC throughout the building.) If the site will not accommodate the required restoration equipment, the companies would then need to quickly arrange with local authorities for street closures, rights of way or other possible options available.

Time is Money Join Law Insider Premium to draft better contracts faster.