Engineering Drawings Clause Samples
The 'Engineering Drawings' clause defines the requirements and standards for the preparation, submission, and approval of technical drawings related to a project. Typically, it outlines the formats, level of detail, and timelines for delivering these drawings, and may specify who is responsible for reviewing and approving them. This clause ensures that all parties have a clear and consistent understanding of the project's technical specifications, reducing the risk of errors or misunderstandings during construction or manufacturing.
POPULAR SAMPLE Copied 7 times
Engineering Drawings. 4.1 The Developer covenants and agrees that the Engineering Drawings for the construction and installation of the Local Improvements for the Development Area shall conform strictly to the Design Standards. 20 -DA-
4.2 Subject to the terms of this Agreement, it is understood and agreed to by the Parties that the Developer must construct the Local Improvements in accordance with the Engineering Drawings as approved by the Municipality.
4.3 It is understood and agreed that the Municipality's approval of the Engineering Drawings for the Local Improvements shall be in principle only and, in the case of unforeseen conditions which may adversely affect development, or in the case where a Local Improvement to be built in accordance with the Engineering Drawings would not be suitable for the purposes intended, the detailed design specifications for any of the Local Improvements shall be subject to review and revision, from time to time, by the Municipality in accordance with the Design Standards and in accordance with accepted engineering and construction practices.
Engineering Drawings. Provide detailed containment drawings stamped by a Professional Engineer registered in the State. Include the maximum allowable load for the floor/platform and required clearances in the drawings. Provide details and procedures for staging, installation, moving, and removing the containment. Provide attachment locations, details, and installation procedures.
Engineering Drawings. In cases where the Supplier receives Siemens engineering drawings and then redraws them into the Supplier’s engineering drawing format for internal use, confidentiality of both sets of drawings is to be maintained. Both sets of drawings are to remain the property of Siemens. B. Inspections and tests. Whether required by Siemens or not, the Supplier is responsible for conducting all appropriate inspections and tests that are necessary to confirm that the product made for Siemens in the form delivered to Siemens meets all of its specified requirements and quality attributes.
Engineering Drawings. The Owner covenants and agrees that the intent of this Agreement is that the Owner shall construct fully completed Works and Services, and grant all necessary statutory right(s)-of-way as shown in the Drawings and Specifications prepared by: Under Drawing Nos. and as approved in principle for the purposes of this Agreement by the CSRD Manager of Environment and Engineering Services on the , 20 . Changes to Design by the CSRD day of
Engineering Drawings. The contractor shall prepare and submit product drawings and associated lists as ICDs for both the system and test equipment at the spare part/assembly-level that assure 100% form, fit, and function interchangeability for the FWS-I. The FWS-I Engineering Drawings are a deliverable under CDRL-F002. The ICDs shall contain sufficient information to permit successful completion of the PCA/FCA. The ICDs shall include:
a) Configuration and interface dimensional data applicable to the envelope, mounting and interconnection of the related items;
b) Complete interface engineering requirements (mechanical, electrical, electronic, optical, human, etc.) which affect the physical or functional characteristics of the co-functioning items;
c) Any other characteristics, including material and finishes, which cannot be changed without affecting system interfaces or interfering down to the spareable level.
Engineering Drawings. The Owner will not commence the construction of the Works until the Owner has submitted the plans and specifications for the Works to the City and the City Engineer has approved the plans and specifications for the Works (the approved plans and specifications are herein referred to as the Engineering Drawings
Engineering Drawings. Landlord shall cause the engineering working drawings for the mechanical, electrical, plumbing, fire-alarm and fire sprinkler work in the Premises (the “Engineering Drawings”) to (a) be prepared by one or more of the Architect, the Contractor, subcontractors and/or engineers or other consultants selected and/or retained by the Architect, the Contractor or Landlord, and (b) conform to the Approved Space Plan, the Approved Additional Information, and any then-existing Approved Architectural Drawings (collectively, the “Engineering Requirements”). Engineering Drawings that conform to the Engineering Requirements shall be referred to herein as “Approved Engineering Drawings”. The Approved Architectural Drawings and the Approved Engineering Drawings are collectively referred to herein as the “Approved Construction Drawings.”
Engineering Drawings. HPEC's Technical Representative shall be provided with a copy of all engineering plans, specifications and drawings for the Processor. All engineering plans, specifications and drawings for the Processor are the property of HET.
Engineering Drawings. The Emergency Generator contractor shall prepare and submit for approval, engineering drawings sets for the emergency generator. These specific drawings shall be as follows; >> Interconnection Wiring Schematic Diagrams >> Alarm Wiring Schematic Drawings GENERATOR INSTALLATION All installation work performed shall be in accordance with laws, regulations and ordinances of all State, Local, and Federal agencies. The contractor shall provide all the necessary personnel, tools, equipment, and transportation for the installation of all equipment provided per the RFP specification. It shall be the responsibility of the contractor to provide a turnkey installation of the provided equipment. Optimization, trouble shooting, and adjustment of each subsystem shall be the contractors responsibility. GENERATOR WARRANTY A no deductible warranty that provides for on site service by a factory authorized service contractor shall be provided. This warranty shall provide coverage against all defects in materials and workmanship as defined in Rider F - Warranty and Maintenance. CONTRACTOR RESPONSIBILITIES The generator system contractor shall have turnkey responsibility for the delivery, installation and acceptance testing of the generators. In order to develop a complete and operational system, the points of demarcation between systems and all contractors is critical to the system implementation process. Therefore, the Generator Contractor's responsibilities are defined. The Contractor's Responsibilities listed apply to those commodities and subsystems included in each approved Site Design Document. Contractors shall follow good engineering practices in the preparation, administration, implementation, inspection and acceptance of each individual subsystem at the designated sites. The Site Development Contractor shall be the responsible party for site management and act as the general site manager for all construction and coordination between contractors, vendors and the Commonwealth until Final Site Acceptance by the Commonwealth. The Contractors shall comply with the following representative sequence and order of subsystem installations.
Engineering Drawings. To provide engineering drawings for approval by the Municipal Engineer, inclusive of detailed designs and specifications demonstrating details of all Site Development Works. Without limiting the foregoing, the Owner shall provide engineering drawings detailing, where applicable, all grading, stormwater management, sediment erosion control, easements, servicing, entrance details, road allowance widening, pavement widening, utility construction and any other work required as part of the development. Approval shall be in the sole and absolute discretion of the Municipal Designate. Where any of the drawings forming part of Schedule “G” require amendment, such amendments shall be subject to the approval of the Municipal Engineer, in his/her sole and absolute discretion, and upon approval such plans and drawings shall form part of Schedule “G” to this Agreement where so agreed in writing by the Parties.