Common use of Diagnostics Clause in Contracts

Diagnostics. Diagnostics information and help materials for pinpointing problems in a network can be found under menu item Diagnostics - Network. Information is provided on the following topics: – Routing table Information concerning the accessibility of all nodes within the system network via the respective interface. – Ethernet ports Information concerning different parameters and the status of the two Ethernet interfaces available at the panel controller. – Send ping command Sending of a ping command to a specific IP address to check the availability of other nodes in the network. – Consistency check The check performed determines whether the Ethernet configuration from FSP-5000-RPS corresponds to the configuration entered at the panel controller. In the event of discrepancies, a fault message is displayed. – Ethernet redundancy Information concerning the type of redundancy configuration (RSTP or dual-homing). In the case of redundancy via RSTP, the RSTP parameters of the RSTP panel and those of the root bridge are displayed. Further information can be found in Network services, page 66. 8 Remote keypad‌ In the FSP-5000-RPS programming software, the address of a panel to which a connection is automatically made from the remote keypad can be entered in the dialog regarding the node of the remote keypad. In addition, further panels with which a connection can be made can also be assigned. It is not possible to log out of the automatically assigned connection. A connection can be established with other panels without any further queries.

Diagnostics. Diagnostics information and help materials for pinpointing problems in a network can be found under menu item Diagnostics - Network. Information is provided on the following topics: – Routing table Information concerning the accessibility of all nodes within the system network via the respective interface. – Ethernet ports Information concerning different parameters and the status of the two Ethernet interfaces available at the panel controller. – Send ping command Sending of a ping command to a specific IP address to check the availability of other nodes in the network. – Consistency check The check performed determines whether the Ethernet configuration from FSP-5000-RPS corresponds to the configuration entered at the panel controller. In the event of discrepancies, a fault message is displayed. – Ethernet redundancy Information concerning the type of redundancy configuration (RSTP or dual-homing). In the case of redundancy via RSTP, the RSTP parameters of the RSTP panel and those of the root bridge are displayed. Further information can be found in Network services, page 6664. 8 Remote keypad‌ keypad‌‌ In the FSP-5000-RPS programming software, the address of a panel to which a connection is automatically made from the remote keypad can be entered in the dialog regarding the node of the remote keypad. In addition, further panels with which a connection can be made can also be assigned. It is not possible to log out of the automatically assigned connection. A connection can be established with other panels without any further queries.

Diagnostics. Diagnostics information and help materials for pinpointing problems in a network can be found under menu item Diagnostics - Network. Information is provided on the following topics: – Routing table Information concerning the accessibility of all nodes within the system network via the respective interface. – Ethernet ports Information concerning different parameters and the status of the two Ethernet interfaces available at the panel controller. – Send ping command Sending of a ping command to a specific IP address to check the availability of other nodes in the network. – Consistency check The check performed determines whether the Ethernet configuration from FSP-5000-RPS corresponds to the configuration entered at the panel controller. In the event of discrepancies, a fault message is displayed. – Ethernet redundancy Information concerning the type of redundancy configuration (RSTP or dual-homing). In the case of redundancy via RSTP, the RSTP parameters of the RSTP panel and those of the root bridge are displayed. Further information can be found in Network services, page 6664. 8 Remote keypad‌ In the FSP-5000-RPS programming software, the address of a panel to which a connection is automatically made from the remote keypad can be entered in the dialog regarding the node of the remote keypad. In addition, further panels with which a connection can be made can also be assigned. It is not possible to log out of the automatically assigned connection. A connection can be established with other panels without any further queries.

Diagnostics. Diagnostics information and help materials for pinpointing problems in a network can be found under menu item Diagnostics - Network. Information is provided on the following topics: – Routing table Information concerning the accessibility of all nodes within the system network via the respective interface. – Ethernet ports Information concerning different parameters and the status of the two Ethernet interfaces available at the panel controller. – Send ping command Sending of a ping command to a specific IP address to check the availability of other nodes in the network. – Consistency check The check performed determines whether the Ethernet configuration from FSP-5000-RPS corresponds to the configuration entered at the panel controller. In the event of discrepancies, a fault message is displayed. – Ethernet redundancy Information concerning the type of redundancy configuration (RSTP or dual-homing). In the case of redundancy via RSTP, the RSTP parameters of the RSTP panel and those of the root bridge are displayed. Further information can be found in Network services, page 6665. 8 Remote keypad‌ keypad‌‌ In the FSP-5000-RPS programming software, the address of a panel to which a connection is automatically made from the remote keypad can be entered in the dialog regarding the node of the remote keypad. In addition, further panels with which a connection can be made can also be assigned. It is not possible to log out of the automatically assigned connection. A connection can be established with other panels without any further queries.