Common use of Description Requirement Clause in Contracts

Description Requirement. Drawing Number(s) W865 – Main Frame W903 – Frame Assembly (As used with Ammunition Container L30A4) W904 – Main Frame, Sub Assembly W907 – Rear Panel (Aluminium) SV695A Issue 2-Pallet with Beech Wood Bearers SV3789 – Pallet Bearer (Wooden) SV4096 – Pallet Bearer (Wooden) SV3565 Pallet Leg SV3568 Pallet Leg SV4097 Pallet Leg SV4098 Pallet Leg SV4099 Corner Plate SV4100 Corner Plate SV3564 Centre Plate SV4111 Issue 1-Board (Plywood) SV4081 Issue 1-Side Panel (Aluminium) W908 – Gate Assembly (As used with Ammunition Container L30A4) W910 – Gate Panel (Aluminium) SV384SA-Latch Gate SV4116-Bracket SV4117-Bolt SV4070-Pin SV3753-Retainer SV385SA-Latch Gate SV4114-Bracket SV4115-Bolt SV4070-Pin SV3753-Retainer SV749A Issue 2 – Helitubes (As used with Ammunition Container L30A2/A3) DT500049 –Reducing ▇▇▇▇ SV403SA – Helitube Body SV4386 – ▇▇▇▇ SV4387 – Diaphragm SV4388 - ▇▇▇▇ SV4122 Issue 1 – Base Board (As used with Ammunition Container L30A4) (Plywood) Material Steel/Wood/Aluminium Colour(s) BS381c - 499 Service Brown Contract Item Number 26 Inspection & Pre- preparation Check modification to SK500036 on frame and door has been carried out making it an L30A2/B2; exchange if not modified. Check integrity and condition of Frame Assembly -W903 including Board SV4111, Side Panel SV4081, Base Board SV4122 and Rear Panel W907. Those worst than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Those worse than the minimum pre refurbishment acceptable visual standard and fail integrity-check are to be rejected and exchanged or replaced. Any split, delaminated and or punctured wood is to be replaced. Check integrity and condition and ISPM 15 compliancy/marking of the bearers (SV3789/4096) on SV695A-Pallet Assembly and exchange or replace. As long as inherent cracks in wood are not aligned rivet to rivet the bearer can be conditioned fit for purpose. Those worse than the minimum pre refurbishment acceptable visual standard and fail integrity- check are to be rejected and exchanged or replaced. Checking integrity and function of Gate Assembly W908, including latches SV384SA & SV385SA and Gate Panel Aluminium W910. Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Remove Shell helitubes and check they are an L421A3 (SV749A). If any are an L421A2 or L421A4, replace. Check integrity and condition including presence of SV4387 Diaphragm, SV4388 ▇▇▇▇ and SV4386 ▇▇▇▇. Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced, including those with a missing ▇▇▇▇ or Diaphragm. Use Block Gauge to ensure the internal volumetrics of specified containers have not been compromised by previous damage, distortion and/or refurbishment. Check integrity and condition of M10 bolts, nuts and washers. All heavily corroded items are to be replaced. Likewise nut/bolt combinations which are not free running.

Description Requirement. Drawing Number(s) W865 – Main Frame W903 – Frame Assembly (As used with Ammunition Container L30A4) W904 – Main Frame, Sub Assembly W907 – Rear Panel (Aluminium) SV695A Issue 2-Pallet with Beech Wood Bearers SV3789 – Pallet Bearer (Wooden) SV4096 – Pallet Bearer (Wooden) SV3565 Pallet Leg SV3568 Pallet Leg SV4097 Pallet Leg SV4098 Pallet Leg SV4099 Corner Plate SV4100 Corner Plate SV3564 Centre Plate SV4111 Issue 1-Board (Plywood) SV4081 Issue 1-Side Panel (Aluminium) W908 – Gate Assembly (As used with Ammunition Container L30A4) W910 – Gate Panel (Aluminium) SV384SA-Latch Gate SV4116-Bracket SV4117-Bolt SV4070-Pin SV3753-Retainer SV385SA-Latch Gate SV4114-Bracket SV4115-Bolt SV4070-Pin SV3753-Retainer SV749A Issue 2 – Helitubes (As used with Ammunition Container L30A2/A3) DT500049 –Reducing ▇▇▇▇ SV403SA – Helitube Body SV4386 – ▇▇▇▇ SV4387 – Diaphragm SV4388 - ▇▇▇▇ SV4122 Issue 1 – Base Board (As used with Ammunition Container L30A4) (Plywood) Material Steel/Wood/Aluminium Colour(s) BS381c - 499 Service Brown Contract Item Number 26 27 Inspection & Pre- preparation Check modification to SK500036 on frame and door has been carried out making it an L30A2L30A3/B2; exchange if not modified. Check integrity and condition of Frame Assembly -W903 including Board SV4111, Side Panel SV4081, Base Board SV4122 and Rear Panel W907. Those worst worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Those worse than the minimum pre refurbishment acceptable visual standard and fail integrity-check are to be rejected and exchanged or replaced. Any split, delaminated and or punctured wood is to be replaced. Check integrity and condition and ISPM 15 compliancy/marking of the bearers (SV3789/4096) on SV695A-Pallet Assembly and exchange or replace. As long as inherent cracks in wood are not aligned rivet to rivet the bearer can be conditioned fit for purpose. Those worse than the minimum pre refurbishment acceptable visual standard and fail integrity- check are to be rejected and exchanged or replaced. Checking integrity and function of Gate Assembly W908, including latches SV384SA & SV385SA and Gate Panel Aluminium W910. Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Remove Shell helitubes and check they are an L421A3 (SV749A). If any are an L421A2 or L421A4, replace. If there are any L421A3” modified” (identifiable by the presence of support ring W869), carry out restoration as Item M of the SoR. Check integrity and condition including presence of SV4387 Diaphragm, SV4388 ▇▇▇▇ and SV4386 ▇▇▇▇. Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced, including those with a missing ▇▇▇▇ or Diaphragm. Use Block Gauge to ensure the internal volumetrics of specified containers have not been compromised by previous damage, distortion and/or refurbishment. Item M of the SoR as required above is the following restoration: Fold flat the top three tabs. Remove the additional support ring W869. Fold flat the lower three tabs. Planish flat all 6 tabs to ensure the internal dimension of the tube is not compromised. Remove reducing ▇▇▇▇ DT500248. The tube is now classed as a L421A3. Check integrity and condition of M10 bolts, nuts and washers. All heavily corroded items are to be replaced. Likewise nut/bolt combinations which are not free running.

Description Requirement. Drawing Number(s) W865 – SV723A Issue 1 –Main Frame W903 – Frame Assembly (As used with Ammunition Container L30A4) W904 – Main Frame, Sub Assembly W907 – Rear Panel (Aluminium) SV695A Issue 2-General Arrangement SV4222 issue 3-Pallet with Beech Wood Bearers SV3789 – Pallet Bearer (Wooden) SV4096 – Pallet Bearer (Wooden) SV3565 Pallet Leg SV3568 Pallet Leg SV4097 Pallet Leg SV4098 Pallet Leg SV4099 Corner Plate SV4100 Corner Plate SV3564 Centre Plate SV4111 Charge Helitubes SV4091 Issue 1-Base Board – Plywood SV689A Issue 2 -Frame Assembly SV3785 – Rear Gate Panels (Steel) SV4084- Bearer (Plywood) SV4085-Bearer (Plywood) SV383SA - Cover SV378SA – Panel Sub Assembly SV4081 Issue 1-– Side Panel (Aluminium) W908 SV4082 – Gate Bracket SV335SA-Igniter Housing SV3557 – Cover SV3558 – Lid SV3559 – End PlateSV690A Issue 2 -Gate Assembly (As used with Ammunition Container L30A4) W910 – Gate Panel (Aluminium) SV384SA-Latch Gate gate SV4116-Bracket SV4117-Bolt SV4070-Pin SV3753-Retainer SV385SA-Latch Gate gate SV4114-Bracket SV4115-Bolt SV4070-Pin SV3753-Retainer SV749A Issue 2 – Helitubes SV4087-Panel (As used with Ammunition Container L30A2/A3) DT500049 –Reducing ▇▇▇▇ SV403SA – Helitube Body SV4386 – ▇▇▇▇ SV4387 – Diaphragm SV4388 - ▇▇▇▇ SV4122 Issue 1 – Base Board (As used with Ammunition Container L30A4) (PlywoodAluminium) Material Steel/Wood/Aluminium Colour(s) BS381c - 499 Service Brown Contract Item Number 26 25 Inspection & Pre- preparation Check modification to SK500036 on frame Remove slings and door has been carried out making it an L30A2/B2; exchange if not modified. Check securing pins Checking integrity and condition function of Frame Gate Assembly -W903 including Board SV4111, Side SV690A. Including latches SV384Sa & SV385SA and Panel SV4081, Base Board SV4122 and Rear Panel W907Aluminium SV4087. Those worst worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Those worse than the minimum pre refurbishment acceptable visual standard and fail integrity-check are to be rejected and exchanged or replaced. Any split, delaminated and or punctured wood is to be replaced. Check integrity and condition of Frame Assembly SV689A including Rear Gate Steel Panels SV3785, Cover SV383SA and ISPM 15 compliancy/marking of the bearers (SV3789/4096) on SV695A-Pallet Panel Assembly and exchange or replace. As long as inherent cracks in wood are not aligned rivet to rivet the bearer can be conditioned fit for purpose. Those worse than the minimum pre refurbishment acceptable visual standard and fail integrity- check are to be rejected and exchanged or replaced. Checking integrity and function of Gate Assembly W908, including latches SV384SA & SV385SA and Gate Panel Aluminium W910SV378SA. Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Remove Shell helitubes Bearers SV4084 & SV4085 and check they are an L421A3 (SV749A). If any are an L421A2 or L421A4, replacereplace with new during final assembly. Check integrity and condition including presence of SV4387 Diaphragm, SV4388 ▇▇▇▇ and SV4386 ▇▇▇▇. Helitubes SV4222 (Aluminium) Those worse than the minimum pre refurbishment acceptable visual standard are is to be rejected and exchanged or replaced, including those with a missing ▇▇▇▇ or Diaphragm. Use Block Gauge to ensure the internal volumetrics of specified containers have not been compromised by previous damage, distortion and/or refurbishment. Check integrity and condition of M10 bolts, nuts and washersBase Board SV4091. All heavily corroded items Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Likewise nut/bolt combinations which are not free running.Any split, delaminated and or punctured wood is to be replaced

Description Requirement. Drawing Number(s) W865 SV613 A Issue 6 – L21A1 Assembly SV614A –Main Frame W903 Assembly SV3727 – Marking Plate (Steel) SV3728 – Frame Panel (Steel) SV3729 – Frame Panel (Steel) SV615A Issues 1 - Pallet Bottom Deck Assembly SV3731 – Bearer (As used with Ammunition Container L30A4Wood) W904 SV3732 – Main Frame, Sub Bearer (Alu Alloy) SV3733 – Spacer SV3734 – Spacer SV3735 - Plate SV616 A Issue 2 – Front Gate SV617A – Gate Assembly W907 SV3743 – Rear Panel Frame panel (Aluminium) SV695A SV3744 – Frame panel (Aluminium) SV3752 Issue1 - Packing pads SV3753 – Retainer SV619A Issue 2-Pallet with Beech Wood Bearers SV3789 1 - Igniter Housing SV620A – Top Frame Assembly SV3756 – Pallet Bearer (Wooden) SV4096 – Pallet Bearer (Wooden) SV3565 Pallet Leg SV3568 Pallet Leg SV4097 Pallet Leg SV4098 Pallet Leg SV4099 Corner Plate SV4100 Corner Plate SV3564 Centre Plate SV4111 Issue 1-Board Top Deck (Plywood) SV4081 Issue 1-Side Panel SV3757 – Tray Lower (AluminiumPlywood) W908 SV3758 – Gate Assembly Tray Upper (As used with Ammunition Container L30A4Plywood) W910 SV3759 – Gate Panel (Aluminium) SV384SA-Latch Gate SV4116-Bracket SV4117-Bolt SV4070-Pin SV3753-Retainer SV385SA-Latch Gate SV4114-Bracket SV4115-Bolt SV4070-Pin SV3753-Retainer SV749A Issue 2 – Helitubes (As used with Ammunition Container L30A2/A3) DT500049 –Reducing ▇▇▇▇ SV403SA – Helitube Body SV4386 – ▇▇▇▇ SV4387 – Diaphragm SV4388 - ▇▇▇▇ SV4122 Centre Frame SV3760 Issue 1 – Base Board (As used with Ammunition Container L30A4) (Plywood) Lower, Short Helitubes SV3761 Issue 1 – Upper, Long Helitubes Material Steel/Aluminium/Wood/Aluminium Expanded Polyethylene Colour(s) BS381c - 499 Service Brown Contract Item Number 26 23 Inspection & Pre- preparation Check modification to SK500036 on frame Remove slings and door has been carried out making it an L30A2/B2; exchange if not modified. securing pins Check integrity and condition function of Frame Assembly -W903 including Board SV4111front gate (SV616A), Side Panel SV4081, Base Board SV4122 and Rear Panel W907. Those worst elements worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Check integrity and service date of Igniter housing packing pads SV3752. Remove split, torn, damaged components. Internal pads older than 5-years are to be replaced. Remove any foreign bodies located behind pads. Remove upper and lower helitubes (SV3761 & SV3760) – check integrity and condition. Those worse than the minimum pre refurbishment acceptable visual standard and fail integrity-check are to be rejected and exchanged or replaced. Any splitUse Block Gauge to ensure the internal volumetrics of specified containers have not been compromised by previous damage, delaminated distortion and/or refurbishment. Check integrity and or punctured wood is condition of aluminium frame panels (SV3743 & SV3744) and Top frame assembly (SV620A). Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Check integrity and condition of steel frame panels (SV3728 & SV3729) and Centre frame (SV3759). Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Check integrity and condition of steel marking plate (SV3727). Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Check integrity, condition and ISPM 15 compliancyCompliancy/marking Marking of the wooden bearers (SV3789/4096SV3731) on SV695A-the Pallet Bottom Deck Assembly (SV615A) and exchange or replace. As long as inherent cracks in wood are not aligned rivet to rivet the bearer can be conditioned fit for purpose. Those worse than the minimum pre refurbishment acceptable visual standard and fail integrity- integrity-check are to be rejected and exchanged or replaced. Checking Check integrity and function condition of Gate Assembly W908aluminium bearer (SV3732). Those worst than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Check integrity and condition of plywood sheets- SV3756 (Pallet Top Deck), including latches SV384SA & SV385SA SV3757 (tray lower) and Gate Panel Aluminium W910SV3758 (tray upper). Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced. Remove Shell helitubes Any split, delaminated and check they are an L421A3 (SV749A). If any are an L421A2 or L421A4, replacepunctured wood is to be replaced. Check integrity and condition including presence of SV4387 Diaphragm, SV4388 ▇▇▇▇ and SV4386 ▇▇▇▇Igniter Housing (SV619A). Those worse than the minimum pre refurbishment acceptable visual standard are to be rejected and exchanged or replaced, including those with a missing ▇▇▇▇ or Diaphragm. Use Block Gauge to ensure the internal volumetrics of specified containers have not been compromised by previous damage, distortion and/or refurbishment. Check integrity and condition of M10 bolts, nuts and washers. All heavily corroded items are to be replaced. Likewise nut/bolt combinations which are not free running.