Check Scaling and Rescaling
Check Scaling and Rescaling Sample Clauses
Related to Check Scaling and Rescaling
Search and Rescue An employee shall be allowed to take leave with pay to participate without pay and at no further cost to the Agency, in a search or rescue operation within Oregon at the request of any law enforcement Agency, the Director of the Department of Aviation, the United States Forest Service, or any certified organization for Civil Defense for a period of no more than five (5) consecutive days for each operation. The employee, upon returning to duty at the Agency, will provide to the Agency documented evidence of participation in the search operation.
Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.
Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. Purchaser may buck out cull material when necessary to produce pieces meeting Utilization Standards. Such bucked out material shall contain a minimum amount of sound wood, not in excess of the net scale in percentage of gross scale, or based on the merchantability factor, whichever is stated in A2. If necessary to assess extent of defect, Purchaser shall make sample saw cuts or wedges. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
Scaling “Scaling,” as used herein, involves:
cont'd The volume and proportion of Credits relating to learners from different protected characteristic groups and Care Experienced Disability - Volume of Credits delivered to students with a known disability 31,014 31,875 32,355 32,355 Proportion 16.7% 17.1% 17.3% 17.3% Care Experience - Volume of Credits delivered to students with Care Experience 1,617 2,066 2,231 2,439 Proportion 0.9% 1.1% 1.2% 1.3%
Archiving and Reuse Self-Archiving: The Publisher permits the Rights Holder to archive the Contribution in accordance with the Publisher's guidelines, the current version of which is set out in the Appendix "Author's Self-Archiving Guidelines".
Local Control Center, Metering and Telemetry The NTO shall operate, pursuant to ISO Tariffs, ISO Procedures, Reliability Rules and all other applicable reliability rules, standards and criteria on a twenty-four (24) hour basis, a suitable local control center(s) with all equipment and facilities reasonably required for the ISO to exercise ISO Operational Control over NTO Transmission Facilities Under ISO Operational Control, and for the NTO to fulfill its responsibilities under this Agreement. Operation of the NYS Power System is a cooperative effort coordinated by the ISO control center in conjunction with local control centers and will require the exchange of all reasonably necessary information. The NTO shall provide the ISO with Supervisory Control and Data Acquisition (“SCADA”) information on facilities listed in Appendices A-1 and A-2 herein as well as on generation and merchant transmission resources interconnected to the NTO’s transmission facilities pursuant to the ISO OATT. The NTO shall provide metering data for its transmission facilities to the ISO, unless other parties are authorized by the appropriate regulatory authority to provide metering data. The NTO shall collect and submit to the ISO billing quality metering data and any other information for its transmission facilities required by the ISO for billing purposes. The NTO shall provide to the ISO the telemetry and other operating data from generation and merchant transmission resources interconnected to its transmission facilities that the ISO requires for the operation of the NYS Power System. The NTO will establish and maintain a strict code of conduct to prevent such information from reaching any unauthorized person or entity.
TEACHERS AND RESEARCHERS 1. An individual who is a resident of a Contracting State immediately before making a visit to the other Contracting State, and who, at the invitation of any university, college, school or other similar educational institution, visits that other State for a period not exceeding two years solely for the purpose of teaching or research or both at such educational institution shall be exempt from tax in that other State on any remuneration for such teaching or research.
COMPLAINTS HANDLING AND RESOLUTION 44.1 The Supplier shall notify the Authority of any Complaints made by Other Contracting Bodies, which are not resolved by operation of the Supplier's usual complaints handling procedure within five (5) Working Days of becoming aware of that Complaint and such notice shall contain full details of the Supplier's plans to resolve such Complaint.
Lunch and Rest Breaks (a) Normally, a non-paid lunch break of either one half (½) hour or one (1) hours duration will be taken halfway through each shift. However, if job conditions require, the lunch break may be moved up to one (1) hour in either direction.
