Calculating Total Average Churn. Total Average Churn is calculated by [***]
Calculating Total Average Churn Sample Clauses
Related to Calculating Total Average Churn
Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.
Total Net Leverage Ratio Maintain as of the end of each fiscal quarter, a Total Net Leverage Ratio for Quantum and its Subsidiaries, on a consolidated basis, of not greater than the ratio set forth below for each four (4) consecutive fiscal quarter period then ended set forth below: Fiscal Quarter Ending Maximum Total Net Leverage Ratio September 30, 2021 4.25:1.00 December 31, 2021 4.25:1.00 March 31, 2022 Not Tested June 30, 2022 3.50:1.00 September 30, 2022 3.50:1.00 December 31, 2022 3.50:1.00 March 31, 2023 3.50:1.00 June 30, 2023 3.00:1.00 September 30, 2023 3.00:1.00 December 31, 2023 3.00:1.00 March 31, 2024 3.00:1.00 June 30, 2024 3.00:1.00 September 30, 2024 3.00:1.00 December 31, 2024 3.00:1.00 March 31, 2025 3.00:1.00 June 30, 2025 3.00:1.00 December 31, 2025 and each fiscal quarter ending thereafter 3.00:1.00”
Maximum Total Leverage Ratio Permit the Total Leverage Ratio of Borrower on a Consolidated Basis, measured for each period of four consecutive fiscal quarters, on the last day of each fiscal quarter (each a “Measurement Date”), to be greater than the ratio set forth below for the corresponding period at any time: Period Ratio Closing Date through September 30, 2017 5.00:1.00 December 31, 2017 through March 31, 2018 4.75:1.00 June 30, 2018 through September 30, 2018 4.50:1.00 December 31, 2018 through March 31, 2019 4.25:1.00 June 30, 2019 and thereafter 4.00:1.00
Maximum Leverage Permit, as of any fiscal quarter end, the ratio of (a) Adjusted Portfolio Equity as of such fiscal quarter end to (b) Funded Debt as of such fiscal quarter end, to be less than 5.00 to 1.00.
Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.
Average Annual Compensation The Executive's "Average Annual Compensation" for purposes of this Agreement shall be deemed to mean the average level of compensation paid to the Executive by the Employers or any subsidiary thereof during the most recent five taxable years preceding the Date of Termination, including Base Salary and benefits and bonuses under any employee benefit plans of the Employers.
Minimum Cash Balance Licensee shall fund the Facility Checking Account --------------------- with an initial amount equal to $25,000.00 and thereafter Licensee shall provide the working capital required by Section I(H) of this Agreement
Measurement Period (b) In this Agreement, unless the contrary intention appears, a reference to:
Maximum Consolidated Leverage Ratio The Consolidated Leverage Ratio at any time may not exceed 0.75 to 1.00; and
Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.
