Ceramic Tile definition

Ceramic Tile means a ceramic surfacing unit made from clay or a mixture of clay and other materials.
Ceramic Tile. Four inch square glazed wall ceramic tile shall be provided at all fixture surrounds and wainscoating shall be five (5) feet above the floor as provided for in the Drawings. Toilet floor tile shall be 8 x 8 inch ceramic pavers or 2x2 inch mosaic tile with a marble threshold.
Ceramic Tile other: Den: Carpet: Laminate: Vinyl: Hardwood: Ceramic Tile: other:

Examples of Ceramic Tile in a sentence

  • Comply with TCA's "Handbook for Ceramic Tile Installation" for TCA installation methods specified in tile installation schedules.

  • Comply with parts of the ANSI A108 Series "Specifications for Installation of Ceramic Tile" that are referenced in TCA installation methods, specified in tile installation schedules, and apply to types of setting and grouting materials used.

  • Comply with parts of the ANSI A108 series "Specifications for Installation of Ceramic Tile" that are referenced in TCNA installation methods, specified in tile installation schedules, and apply to types of setting and grouting materials used.

  • ANSI Tile Installation Standards: Comply with parts of ANSI A108 Series "Specifications for Installation of Ceramic Tile" that apply to types of setting and grouting materials and to methods indicated in ceramic tile installation schedules.

  • Resistance to Wear of Unglazed Ceramic Tile by Taber Abrasion per ASTM C501-84 (re approved 2002) shall not be less than 500.

  • TCA's "Handbook for Ceramic Tile Installation." Comply with TCA installation methods indicated in ceramic tile installation schedules.

  • Provide tile that complies with ANSI A137.1, "Specifications for Ceramic Tile," for types, compositions, and other characteristics indicated.

  • Standard Test Method for Determining the Static Coefficient of Friction of Ceramic Tile and Other Like Surfaces by the Horizontal Dynamometer Pull-Meter Method.

  • Mix and proportion cementitious materials for site-made leveling coats, setting beds and grout as recommended by the TCA Handbook for Ceramic Tile Installation.

  • Cleaning the floor and wall from all stains etc complete .6.2 Ceramic Tile Flooring and Dado/Skirting : 6.2.1 GeneralThis item relates to the furnishing of materials and installations of ceramic tiles in flooring ,dado, etc.


More Definitions of Ceramic Tile

Ceramic Tile. All restrooms shall receive 1"x1" unglazed tile by Dal-Tile.
Ceramic Tile. Toilet room floors, base and wet walls to ceiling will be finished with ceramic tile. Floor tile will be 2” x 2” unglazed. Wall tile shall be 41/4” x 41/4” glazed. Material shall be Dal-Tile or equal. Ceramic tile will be included as part of the Office Buildout Allowance. Floor Sealer and Joint Filler: Warehouse to receive 2 coats of Ashford floor sealer. Semi-rigid control joint filler will be installed at the dock bay(s) only. 09900 Paint Paint materials shall be Bxxxxxxx Xxxxx, Sxxxxxx Xxxxxxxx or equal.
Ceramic Tile. All Floor areas and 4' high at all sink, at Restrooms urinal and water closet areas (i.e. wet walls only). Grout to be sealed. Standard tile type and color to be approved by tenant. Floor Drains - At least one drain shall be provided in each restroom. Entire floor shall slope to drain. Water - One to be provided in warehouse lunchroom and Fountain one to be provided at office restroom core. (Recessed)

Related to Ceramic Tile

  • Negative pressure respirator (tight fitting) means a respirator in which the air pressure inside the facepiece is negative during inhalation with respect to the ambient air pressure outside the respirator.

  • Metallic coating means a coating which contains more than five grams of metal particles per liter of coating, as applied. Metal particles are pieces of a pure elemental metal or a combination of elemental metals.

  • Tight-fitting facepiece means a respiratory inlet covering that forms a complete seal with the face.

  • explosive actuated fastening device means a tool that is activated by an explosive charge and that is used for driving bolts, nails and similar objects for the purpose of providing fixing;

  • Faux finishing coating means a coating labeled and formulated as a stain or a glaze to create artistic effects including, but not limited to, dirt, old age, smoke damage, and simulated marble and wood grain.

  • Nitrogen oxides means nitric oxide and nitrogen dioxide, expressed as nitrogen dioxide (NO2);

  • Sensor means any measurement device that is not part of the vehicle itself but installed to determine parameters other than the concentration of gaseous and particle pollutants and the exhaust mass flow.

  • Antenna coating means a coating labeled and formulated exclusively for application to equipment and associated structural appurtenances that are used to receive or transmit electromagnetic signals.

  • Polystyrene foam adhesive means an aerosol adhesive designed to bond polystyrene foam to substrates.

  • medium voltage means the set of nominal voltage levels that lie above low voltage and below high voltage in the range of 1 kV to 44 kV;

  • Vapor tight means equipment that allows no loss of vapors. Compliance with vapor-tight requirements can be determined by checking to ensure that the concentration at a potential leak source is not equal to or greater than 100 percent of the lower explosive limit (LEL) when measured with a combustible gas detector, calibrated with propane, at a distance of 1 inch (2.54 cm) from the source.

  • Fiber means a glass strand or strands which is/are protected by a color coded buffer tube and which is/are used to transmit a communication signal along the glass strand in the form of pulses of light.

  • Beam scattering foil means a thin piece of material (usually metallic) placed in the beam to scatter a beam of electrons in order to provide a more uniform electron distribution in the useful beam.

  • Diatomaceous earth filtration means a process resulting in substantial particulate removal in which a precoat cake of diatomaceous earth filter media is deposited on a support membrane (septum), and while the water is filtered by passing through the cake on the septum, additional filter media known as body feed is continuously added to the feed water to maintain the permeability of the filter cake.

  • Polystyrene foam means blown polystyrene and expanded and

  • Aerosol coating product means a pressurized coating product containing pigments or resins that dispenses product ingredients by means of a propellant, and is packaged in a disposable can for hand-held application, or for use in specialized equipment for ground traffic/marking applications.

  • Filtering facepiece (dust mask) means a negative pressure particulate respirator with a filter as an integral part of the facepiece or with the entire facepiece composed of the filtering medium, not equipped with elastomeric sealing surfaces and adjustable straps.

  • Biodegradable means degradable through a process by which fungi or bacteria secrete enzymes to convert a complex molecular structure to simple gasses and organic compounds.

  • Membrane filtration means a pressure or vacuum driven separation process in which particulate matter larger than 1 micrometer is rejected by an engineered barrier, primarily through a size-exclusion mechanism, and which has a measurable removal efficiency of a target organism that can be verified through the application of a direct integrity test. This definition includes the common membrane technologies of microfiltration, ultrafiltration, nanofiltration, and reverse osmosis.

  • Glass cleaner means a cleaning product designed primarily for cleaning surfaces made of glass. Glass cleaner does not include products designed solely for the purpose of cleaning optical materials used in eyeglasses, photographic equipment, scientific equipment and photocopying machines.

  • Geothermal fluid means water in any form at temperatures greater than 120

  • Defoliant means any substance or mixture of substances intended for causing the leaves or foliage to drop from a plant, with or without causing abscission.

  • Loose-fitting facepiece means a respiratory inlet covering that is designed to form a partial seal with the face.

  • Halogen means one of the chemical elements chlorine, bromine or iodine.

  • Hydrofluorocarbons means compounds that only contain hydrogen, fluorine, and carbon.

  • High-temperature coating means a high performance coating labeled and formulated for application to substrates exposed continuously or intermittently to temperatures above 204oC (400oF).