Applicable Reliability Standard definition

Applicable Reliability Standard means reliability standards established by the Western Electricity Coordinating Council and reliability standards approved by FERC under Section 215 of the Federal Power Act to provide for reliable operation of the bulk power system.
View Source
Applicable Reliability Standard means reliability standards established by the WECC and reliability standards approved by FERC under Section 215 of the Federal Power Act to provide for reliable operation of the bulk power system or, if the WECC and FERC no longer have such standards, reliability standards promulgated by any federal or state agency with exercising valid jurisdiction over the Subject Facilities.
View Source
Applicable Reliability Standard means with respect to a Party, refers to those Reliability Standards that apply to that Party based upon its registered entity status or as otherwise may be determined by FERC, NERC or WECC, as they may be amended from time to time. Reliability Standards are as set forth in Section 215(a)(3) of the Federal Power Act, 16 U.S.C. §824o(a)(3), or any successor legislation imposing mandatory requirements to provide for the reliable operation of the Bulk Power System, as defined in 16 U.S.C. §824o(a)(1), and any regulations validly promulgated thereunder. Reliability Standards include national standards and regional reliability standards promulgated by FERC, NERC and WECC
View Source

Examples of Applicable Reliability Standard in a sentence

  • An Applicable Reliability Standard with equivalent or more stringent requirements shall supersede the above requirements.

  • Interconnection Customer shall: (1) in coordination with NYISO, set the deadband parameter to: (1) a maximum of ±0.036 Hz and set the droop parameter to a maximum of 5 percent; or (2) implement the relevant droop and deadband settings from an approved Applicable Reliability Standard that provides for equivalent or more stringent parameters.

  • The droop characteristic shall be: (1) based on the nameplate capacity of the Large Generating Facility, and shall be linear in the range of frequencies between 59 and 61 Hz that are outside of the deadband parameter; or (2) based on an approved Applicable Reliability Standard providing for an equivalent or more stringent parameter.

  • Developer is required to install a governor or equivalent controls with the capability of operating: (1) with a maximum 5 percent droop ± 0.036 Hz deadband; or (2) in accordance with the relevant droop, deadband, and timely and sustained response settings from an approved Applicable Reliability Standard providing for equivalent or more stringent parameters.

  • Developer shall: (1) in coordination with NYISO, set the deadband parameter to: (1) a maximum of ±0.036 Hz and set the droop parameter to a maximum of 5 percent; or (2) implement the relevant droop and deadband settings from an approved Applicable Reliability Standard that provides for equivalent or more stringent parameters.

  • Interconnection Customer is required to install a governor or equivalent controls with the capability of operating: (1) with a maximum 5 percent droop and ±0.036 Hz deadband; or (2) in accordance with the relevant droop, deadband, and timely and sustained response settings from an approved Applicable Reliability Standard providing for equivalent or more stringent parameters.

  • Neither the Participating TO’s nor the Interconnection Customer’s facilities shall cause excessive voltage flicker nor introduce excessive distortion to the sinusoidal voltage or current waves as defined by ANSI Standard C84.1-1989, in accordance with IEEE Standard 519, any applicable superseding electric industry standard, or any alternative Applicable Reliability Standard or Applicable Reliability Council standard.

  • In the event of a conflict among ANSI Standard C84.1-1989, any applicable superseding electric industry standard, or any alternative Applicable Reliability Standard or Applicable Reliability Council standard, the alternative Applicable Reliability Standard or Applicable Reliability Council standard shall control.

  • Interconnection Customer is required to install a governor or equivalent controls with the capability of operating: (1) with a maximum 5 percent droop and ±0.036 Hz deadband; or (2) in accordance with the relevant droop, deadband, and timely and sustained response settings from an approved Applicable Reliability Standard providing for equivalent or more stringent SERVICE AGREEMENT NO.

  • A FERC-approved Applicable Reliability Standard with equivalent or more stringent requirements shall supersede the above requirements.


More Definitions of Applicable Reliability Standard

Applicable Reliability Standard means a Reliability Standard that is applicable by law to Lompoc in its capacity as an LSE and/or DP.
View Source

Related to Applicable Reliability Standard

  • Reliability Standard means a requirement to provide for reliable operation of the bulk power system, including without limiting the foregoing requirements for the operation of existing bulk power system facilities, including cybersecurity protection, and the design of planned additions or modifications to such facilities to the extent necessary for reliable operation of the bulk power system, but shall not include any requirement to enlarge bulk power system facilities or to construct new transmission capacity or generation capacity.

  • Reliability Standards means the criteria, standards, rules and requirements relating to reliability established by a Standards Authority.

  • NERC Reliability Standards means the most recent version of those reliability standards applicable to the Generating Facility, or to the Generator Owner or the Generator Operator with respect to the Generating Facility, that are adopted by the NERC and approved by the applicable regulatory authorities, which are available at ▇▇▇▇://▇▇▇.▇▇▇▇.▇▇▇/files/Reliability_Standards_Complete_Set.pdf, or any successor thereto.

  • Service Level Standards has the meaning ascribed thereto in Section 2.1 hereof.

  • Locational Deliverability Area Reliability Requirement means the projected internal capacity in the Locational Deliverability Area plus the Capacity Emergency Transfer Objective for the Delivery Year, as determined by the Office of the Interconnection in connection with preparation of the Regional Transmission Expansion Plan, less the minimum internal resources required for all FRR Entities in such Locational Deliverability Area.