Removal of Loads from Rails Clause Samples

Removal of Loads from Rails. In order to enhance employees’ opportunities to obtain a full-time job and improve the Company’s ability to reduce time-in-transit and improve service, the following provisions will apply: 1. The Company commits that the number of new drivers needed to remove loads from the rail shall be, at least, two thousand (2000), over the life of the current contract. The Company shall be required to train or hire, at least two hundred (200) drivers by December 31, 2019 and twenty-five percent (25%) of the remaining needed drivers each calendar year thereafter. As long as the Company satisfies these hiring/training obligations, it shall have the right to cover these runs with substitute means of transportation. The Employer shall provide the Union a report identifying the loads covered by this Section. The Company shall meet with the Union to resolve any issues which may arise if circumstances beyond the Company’s control preclude the Company from training or hiring needed drivers in any area. The Company shall train or hire a sufficient number of drivers to cover these runs by the end of the current labor agreement. 2. The Company shall provide the Package Division Director its initial plans to remove and cover these loads. In addition, upon request, the Company will review with the Package Division Director, or his designee, the Company’s progress in implementing this Section. The review shall include the Company’s hiring and training of drivers to ensure that reasonable efforts are being made to staff the runs with bargaining unit employees and eliminate the vendors, as soon as practical. If the Company is not making reasonable progress in training the drivers necessary to replace vendors in any area, UPS’ President of Labor Relations and the IBT Package Division Director shall have the authority to determine how and where training will be accomplished. 3. Article 43 shall apply to these runs except for the approval process.
View SourceView Similar (19)

Related to Removal of Loads from Rails

  • Removal of Fixtures (a) So long as the Tenant is not in default hereunder at the expiration of the Term, the Tenant shall then have the right to remove its trade fixtures from the Premises but shall make good any damage caused to the Premises resulting from the installation or removal thereof; provided that all alterations, additions and improvements constructed and installed in the Premises and attached in any manner to the floors, walls or ceiling, including any floor covering and light fixtures, are hereby deemed not to be trade fixtures and shall remain upon and be surrendered with the Premises, except to the extent the Landlord requires removal thereof. (b) If the Tenant fails to remove its trade fixtures and restore the Premises as aforesaid, all such trade fixtures shall become the property of the Landlord except to the extent that the Landlord continues to require removal thereof. (c) Should the Tenant abandon the Premises or should this Lease be terminated before the proper expiration of the Term due to a default on the part of the Tenant then, in such event, as of the moment of default by the Tenant, all trade fixtures and furnishings of the Tenant (whether or not attached in any manner to the Premises) shall, except to the extent the Landlord requires the removal thereof, become and be deemed to be the property of the Landlord, without indemnity to the Tenant and as additional liquidated damages in respect of such default but without prejudice to any other right or remedy of the Landlord. (d) Notwithstanding that any trade fixtures, alterations, additions, improvements or fixtures are or may become the property of the Landlord, the Tenant shall forthwith remove all or part of the same and shall make good any damage caused to the Premises resulting from the installation or removal thereof, all at the Tenant’s expense, should the Landlord so require by notice to the Tenant. (e) If the Tenant, after receipt of a notice from the Landlord, fails to promptly remove any trade fixtures, furnishings, alterations, additions, improvements and fixtures in accordance with such notice, then the Landlord may enter into the Premises and remove therefrom all or part of such trade fixtures, furnishings, alterations, additions, improvements and fixtures without any liability and at the expense of the Tenant, which expense shall forthwith be paid by the Tenant to the Landlord.

  • Cost Responsibility for Interconnection Facilities and Distribution Upgrades 4.1 Interconnection Facilities 4.2 Distribution Upgrades

  • Certain Requirements as to Furniture, Equipment and Fixtures If the Assuming Institution purchases owned Bank Premises or accepts an assignment of the lease (or enters into a sublease or a new lease in lieu thereof) for leased Bank Premises as provided in Section 4.6(a) or 4.6(b), or if the Assuming Institution does not exercise such option but within twelve (12) months following Bank Closing obtains the right to occupy such premises (whether by assignment, lease, sublease, purchase or otherwise), other than in accordance with Section 4.6(a) or (b), the Assuming Institution shall (i) effective as of the date of Bank Closing, purchase from the Receiver all Furniture and Equipment and Fixtures owned by the Failed Bank at Fair Market Value and located thereon as of Bank Closing, (ii) accept an assignment or a sublease of the leases or negotiate new leases for all Furniture and Equipment and Fixtures leased by the Failed Bank and located thereon, and (iii) if applicable, accept an assignment or a sublease of any ground lease or negotiate a new ground lease with respect to any land on which such Bank Premises are located; provided, that the Receiver shall not have disposed of such Furniture and Equipment and Fixtures or repudiated the leases specified in clause (ii) or (iii).

  • Required Bonding Capacity Letter No response If proposing on Part 2, Vendor is required to upload a Bonding Capacity Letter from its surety, as described herein, at this location. Please see the attachment entitled "Instructions and Sample - Part 2 Required Bonding Capacity Letter" for complete instructions. . On Part 2, Vendor will be scored on the aggregate bonding capacity displayed in the accepted letter. Vendor must provide a current letter (issued on or after the first day of the month preceding the date on which the solicitation was posted) from its surety verifying Vendor’s bonding capacity as described herein. (Ex. if the solicitation/bid posted on February 4, 2022, the letter must be dated on or after January 1 2022. The letter must be issued from Vendor’s Surety companies, on surety company letterhead, must specify the maximum bonding capacity of the Vendor, and must be signed by an authorized representative of the surety company. The issuing surety must be authorized to do business in the State of Texas and must be listed on the Department of the Treasury's Listing of Approved Sureties (Department Circular 570).