Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018) (a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION". (b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014) (a) The Contractor shall comply with the higher-level quality standard(s) listed below. (b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 6 contracts
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at awardinsert location]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 2 contracts
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]TBD." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 1000 N/A N/A N/A N/A 1000AA Destination Government 0003 Destination Government 1000AB Destination Government Destination Government 1100 N/A N/A N/A N/A 1100AA Destination Government 0004 Destination Government 1100AB Destination Government Destination Government 1200 N/A N/A N/A N/A 1200AA Destination Government 0005 Destination Government 1200AB Destination Government Destination Government 1300 N/A N/A N/A N/A 1300AA Destination Government 0006 Destination Government 1300AB Destination Government Destination Government 1400 N/A N/A N/A N/A 1400AA Destination Government 0007 Destination Government 1400AB Destination Government Destination Government 2000 N/A N/A N/A N/A 2000AA Destination Government 0008 Destination Government 2000AB Destination Government Destination Government 2000AC Destination Government Destination Government 2000AD Destination Government Destination Government 2100 N/A N/A N/A N/A 2100AA Destination Government 0009 Destination Government 2100AB Destination Government Destination Government 2200 N/A N/A N/A Government 1001 N/A 2200AA Destination Government Destination Government 1002 2200AB Destination Government Destination Government 2300 N/A N/A N/A N/A 2300AA Destination Government 1003 Destination Government 2300AB Destination Government Destination Government 2400 N/A N/A N/A N/A 2400AA Destination Government 1005 Destination Government 2400AB Destination Government Destination Government 3000 N/A N/A N/A N/A 3000AA Destination Government 1007 Destination Government 3000AB Destination Government Destination Government 3000AC Destination Government Destination Government 3000AD Destination Government Destination Government 3100 N/A N/A N/A Government 2001 N/A 3100AA Destination Government Destination Government 2002 3100AB Destination Government Destination Government 3200 N/A N/A N/A N/A 3200AA Destination Government 2003 Destination Government 3200AB Destination Government Destination Government 3300 N/A N/A N/A N/A 3300AA Destination Government 2005 Destination Government 3300AB Destination Government Destination Government 3400 N/A N/A N/A N/A 3400AA Destination Government 2007 Destination Government 3400AB Destination Government Destination Government 4000 N/A N/A N/A Government 3001 N/A 4000AA Destination Government Destination Government 3002 4000AB Destination Government Destination Government 4000AC Destination Government Destination Government 4000AD Destination Government Destination Government 4100 N/A N/A N/A N/A 4100AA Destination Government 3003 Destination Government 4100AB Destination Government Destination Government 4200 N/A N/A N/A N/A 4200AA Destination Government 3005 Destination Government 4200AB Destination Government Destination Government 4300 N/A N/A N/A N/A 4300AA Destination Government 3007 Destination Government 4300AB Destination Government Destination Government 4400 N/A N/A N/A Government 4001 N/A 4400AA Destination Government Destination Government 4002 4400AB Destination Government Destination Government 5000 N/A N/A N/A N/A 5000AA Destination Government 4003 Destination Government 5000AB Destination Government Destination Government 5000AC Destination Government Destination Government 5000AD Destination Government Destination Government 5100 N/A N/A N/A N/A 5100AA Destination Government 4005 Destination Government 5100AB Destination Government Destination Government 5200 N/A N/A N/A N/A 5200AA Destination Government 4007 Destination Government 5200AB Destination Government Destination Government 5300 N/A N/A N/A N/A 5300AA Destination Government Destination Government 5300AB Destination Government Destination Government 5400 N/A N/A N/A N/A 5400AA Destination Government Destination Government 5400AB Destination Government Destination Government 6000 Destination Government Destination Government 6100 Destination Government Destination Government 6200 Destination Government Destination Government 6300 Destination Government Destination Government 6400 Destination Government Destination Government 7000 Destination Government Destination Government 8000 Destination Government Destination Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018) Inspection and acceptance of all data shall be as specified on the attached Contract Data Requirements List(s), DD Form 1423. E-246-H016 INSPECTION AND ACCEPTANCE OF F.O.B. DESTINATION DELIVERIES (NAVSEA) (OCT 2018) Item(s) CLIN 1000, 1100, 1200, 1300, 1400, 2000, 2100, 2200, 2300, 2400, 3000, 3100, 3200, 3300, 3400, 4000, acceptance shall be made at destination by a representative of the Government. E-246-H020 QUALITY MANAGEMENT SYSTEM REQUIREMENTS (NAVSEA) (OCT 2018) The Contractor shall provide and maintain a quality management system that, as a minimum, adheres to the requirements of ASQ/ANSI/ISO 9001:2015 “Quality Management Systems – Requirements” and supplemental requirements imposed by this contract. The quality management system procedures, planning, and all other documentation and data that comprise the quality management system shall be made available to the Government for review. Existing quality documents that meet the requirements of this contract may continue to be used. The Government may perform any necessary inspections, verifications, and evaluations to ascertain conformance to requirements and the adequacy of the implementing procedures. The Contractor shall flow down such standards, as applicable, to lower-tier subcontractors under instances covered in FAR 52.246-11 HIGHER11(b) or at the direction of the Contracting Officer. The Government reserves the right to disapprove the quality management system or portions thereof when it fails to meet the contractual requirements. E-246-LEVEL CONTRACT QUALITY REQUIREMENT H022 INSPECTION AND TEST RECORDS (DEC 2014NAVSEA) (JAN 2019) Inspection and test records shall, as a minimum, indicate the nature of the observations, number of observations made, and the number and type of deficiencies found. Data included in inspection and test records shall be complete and accurate, and shall be used for trend analysis and to assess corrective action and effectiveness. The data shall, on request, be identified and made available for on-site review by the Contracting Officer or designated Government representative. E-246-W002 CERTIFICATE OF COMPLIANCE (NAVSEA) (OCT 2018)
(a) The Contractor A certification of material shall comply with be provided by the higher-level quality standard(sContractor, one (1) listed below.copy to accompany the shipment (in the packing list envelope) and (l) copy mailed to arrive at time of receipt of the shipment. Mark all certificates to the attention of Code 00Q.
(b) The Contractor certificate shall include applicable requirements state compliance of material with drawing specification and contract/order requirements. The certificate shall as a minimum state the company name, contract/order number, drawing or specification number, and date. The certificate shall state, above the signature of a legally authorized representative of the higher-level company, the following: This certification concerns a matter within the jurisdiction of an agency of the United States and the making of a false, fictitious, or fraudulent certification may render the maker subject to prosecution under Title 18, United States Code, Section 1001.
(c) Failure to provide certification at the time of shipment may result in material being rejected and returned at the contractor's expense.
(d) The certificate shall read as follows: I certify that on [insert date], the [insert Contractor’s name] furnished the supplies called for by the Order/Contract No. via [Carrier] on [identify the bill of lading or shipping document] in accordance with all applicable requirements. I further certify that the supplies or services are of the quality standard(s) listed specified and conform in paragraphall respects with the contract requirements, including specifications, drawings, preservation, packaging, packing, marking requirements, and physical item identification (part number), and are in the quantity shown on this document.
Appears in 2 contracts
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 2 contracts
Sources: Solicitation, Offer and Award, Solicitation, Offer and Award
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 1 contract
Sources: Solicitation
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED TBD [to be completed at awardinsert location]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be NOTES In summary, unless noted in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Suppliesdelivery orders, supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed as specified below.
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]TBD." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 0003 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 0004 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 0005 Destination Government Destination Government 4002 N/A N/A N/A 0006 Destination Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Destination Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-4 Inspection Of Services--Fixed Price AUG 1996 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 52.247-55 F.O.B. Point For Delivery Of Government-Furnished JUN 2003 Property CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.. Title Number Date Tailoring Quality Management Systems Requirements ASQ/ANSI/ISO 9001:2015 October 2015 N/A
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED *Contractor fill in [to be completed at awardinsert location]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Origin Government 0002 Origin Government Origin Government 0003 Origin Government Origin Government 0004 Origin Government Origin Government 0005 Origin Government Origin Government 0006 Origin Government Origin Government 0007 Origin Government Origin Government 0008 Origin Government Origin Government 0009 Origin Government Origin Government 0010 Origin Government Origin Government 0011 Origin Government Origin Government 0012 Origin Government Origin Government 0013 Origin Government Origin Government 0014 Origin Government Origin Government 0015 Origin Government Origin Government 0016 Origin Government Origin Government 0017 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.. NAVSEA S9320-AM-PRO-020
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
(a) of this clause and the requirement to flow down such standards, as applicable, to lower-tier subcontracts, in--
(1) Any subcontract for critical and complex items (see 46.203(b) and (c)); or
(2) When the technical requirements of a subcontract require--
(i) Control of such things as design, work operations, in-process control, testing, and inspection; or
(ii) Attention to such factors as organization, planning, work instructions, documentation control, and advanced metrology. (End of clause) CLAUSES INCORPORATED BY FULL TEXT E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018) Inspection and acceptance of all data shall be as specified on the attached Contract Data Requirements List(s), DD Form 1423. CLAUSES INCORPORATED BY FULL TEXT E-246-H017 INSPECTION AND ACCEPTANCE OF F.O.B. ORIGIN DELIVERIES (NAVSEA) (OCT 2018) Item(s) 0001 - 0016 - Inspection and acceptance shall be made at source by a representative of the cognizant Contract Administration Office or other representative of the Government. E-246-H020 QUALITY MANAGEMENT SYSTEM REQUIREMENTS (NAVSEA) (OCT 2018) The Contractor shall provide and maintain a quality management system that, as a minimum, adheres to the requirements of ASQ/ANSI/ISO 9001:2015 “Quality Management Systems – Requirements” and supplemental requirements imposed by this contract. The quality management system procedures, planning, and all other documentation and data that comprise the quality management system shall be made available to the Government for review. Existing quality documents that meet the requirements of this contract may continue to be used. The Government may perform any necessary inspections, verifications, and evaluations to ascertain conformance to requirements and the adequacy of the implementing procedures. The Contractor shall flow down such standards, as applicable, to lower-tier subcontractors under instances covered in FAR 52.246-11(b) or at the direction of the Contracting Officer. The Government reserves the right to disapprove the quality management system or portions thereof when it fails to meet the contractual requirements. E-246-H022 INSPECTION AND TEST RECORDS (NAVSEA) (JAN 2019) Inspection and test records shall, as a minimum, indicate the nature of the observations, number of observations made, and the number and type of deficiencies found. Data included in inspection and test records shall be complete and accurate, and shall be used for trend analysis and to assess corrective action and effectiveness. The data shall, on request, be identified and made available for on-site review by the Contracting Officer or designated Government representative. E-246-W007 NOTIFICATION OF INSPECTION OR TEST (NAVSEA) (OCT 2018) The Contractor agrees to notify the TPOC identified in section G, in writing, when the material will be inspected and/or tested. A minimum of 10 working days is required to arrange such a visit. Section F - Deliveries or Performance
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at awardinsert location]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 0003 Destination Government Destination Government 2002 N/A N/A N/A 0004 Origin Government 2003 N/A N/A N/A Origin Government 2005 N/A N/A N/A 0005 Origin Government 2007 N/A N/A N/A Origin Government 3001 0006 Origin Government Origin Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.. ASME Y14.100: 2013
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
(a) of this clause and the requirement to flow down such standards, as applicable, to lower-tier subcontracts, in--
(1) Any subcontract for critical and complex items (see 46.203(b) and (c)); or
(2) When the technical requirements of a subcontract require--
(i) Control of such things as design, work operations, in-process control, testing, and inspection; or (ii) Attention to such factors as organization, planning, work instructions, documentation control, and advanced metrology. (End of clause) CLAUSES INCORPORATED BY FULL TEXT E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018) Inspection and acceptance of all data shall be as specified on the attached Contract Data Requirements List(s), DD Form 1423. CLAUSES INCORPORATED BY FULL TEXT E-246-H016 INSPECTION AND ACCEPTANCE OF F.O.B. DESTINATION DELIVERIES (NAVSEA) (OCT 2018) Item(s) 0001, 0002, 0003 and 0008 - Inspection and acceptance shall be made at destination by a representative of the Government. CLAUSES INCORPORATED BY FULL TEXT E-246-H017 INSPECTION AND ACCEPTANCE OF F.O.B. ORIGIN DELIVERIES (NAVSEA) (OCT 2018) Item(s) 0004, 0005, 0006 and 0007 - Inspection and acceptance shall be made at source by a representative of the cognizant Contract Administration Office or other representative of the Government. E-246-H020 QUALITY MANAGEMENT SYSTEM REQUIREMENTS (NAVSEA) (OCT 2018) The Contractor shall provide and maintain a quality management system that, as a minimum, adheres to the requirements of ASQ/ANSI/ISO 9001:2015 “Quality Management Systems – Requirements” and supplemental requirements imposed by this contract. The quality management system procedures, planning, and all other documentation and data that comprise the quality management system shall be made available to the Government for review. Existing quality documents that meet the requirements of this contract may continue to be used. The Government may perform any necessary inspections, verifications, and evaluations to ascertain conformance to requirements and the adequacy of the implementing procedures. The Contractor shall flow down such standards, as applicable, to lower-tier subcontractors under instances covered in FAR 52.246-11(b) or at the direction of the Contracting Officer. The Government reserves the right to disapprove the quality management system or portions thereof when it fails to meet the contractual requirements. CLAUSES INCORPORATED BY FULL TEXT E-246-H022 INSPECTION AND TEST RECORDS (NAVSEA) (JAN 2019) Inspection and test records shall, as a minimum, indicate the nature of the observations, number of observations made, and the number and type of deficiencies found. Data included in inspection and test records shall be complete and accurate, and shall be used for trend analysis and to assess corrective action and effectiveness. The data shall, on request, be identified and made available for on-site review by the Contracting Officer or designated Government representative. CLAUSES INCORPORATED BY FULL TEXT E-246-W007 NOTIFICATION OF INSPECTION OR TEST (NAVSEA) (OCT 2018) The Contractor agrees to notify the COR identified in Section G, in writing, when the material will be inspected and/or tested. A minimum of 10 business days is required to arrange such a visit. Section F - Deliveries or Performance NOTE FOR DELIVERY INFORMATION Due to a system constraint the delivery dates shown calls for years “After Date of Contract (ADC).” For the purposes of this contract “ADC” is synonymous with “After Receipt of Order (ARO).” In addition, CLINs 0004 – 0007 can be ordered against for the duration of the contract as indicated by the “5 yrs ADC” shown below. However, actual delivery requirements for the items are included in FAR Clause 52.211-8 TIME OF DELIVERY (JUN 1997) below. DELIVERY INFORMATION CLIN DELIVERY DATE QUANTITY SHIP TO ADDRESS DODAAC / CAGE 0001 12 mths. ADC 2 NAVAL STATION NEWPORT, N66604 RECEIVING OFFICER ▇▇ ▇▇▇▇▇▇▇▇ ▇▇▇▇▇▇ NEWPORT RI 02841-1716 401-832-6150 FOB: Destination N66604 0003 12 mths. ADC 2 (SAME AS PREVIOUS LOCATION) FOB: Destination N66604 0004 5 yrs. ADC DLA DISTRIBUTION ▇▇▇▇▇▇▇▇ ▇▇▇▇ ▇▇▇▇▇▇▇ ▇▇▇▇▇▇▇▇ ANNEX ▇ ▇ ▇▇▇▇▇▇ ▇▇▇▇▇▇▇▇▇▇▇▇ ▇▇ ▇▇▇▇▇-0000 757-887-7113 FOB: Origin (Shipping Point) SW3126 0005 5 yrs. ADC (SAME AS PREVIOUS LOCATION) FOB: Origin (Shipping Point) SW3126 0006 5 yrs. ADC (SAME AS PREVIOUS LOCATION) FOB: Origin (Shipping Point) SW3126 0007 5 yrs. ADC (SAME AS PREVIOUS LOCATION) FOB: Origin (Shipping Point) SW3126 0008 5 yrs. ADC 1 NAVAL STATION NEWPORT, N66604 N66604 RECEIVING OFFICER ▇▇ ▇▇▇▇▇▇▇▇ ▇▇▇▇▇▇ NEWPORT RI 02841-1716 ▇▇▇-▇▇▇-▇▇▇▇ FOB: Destination CLAUSES INCORPORATED BY REFERENCE 52.242-15 Stop-Work Order AUG 1989 52.242-17 Government Delay Of Work APR 1984 52.247-29 F.O.B. Origin FEB 2006 52.247-34 F.O.B. Destination NOV 1991 52.247-48 F.O.B. Destination--Evidence Of Shipment FEB 1999 CLAUSES INCORPORATED BY FULL TEXT
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed TBD at award]TO Level." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 0003 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 0004 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 0005 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 4 Inspection Of SuppliesServices--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-13 Inspection--Dismantling, Demolition, or Removal of AUG 1996 Improvements 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
(a) of this clause and the requirement to flow down such standards, as applicable, to lower-tier subcontracts, in--
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]***TO BE SPECIFIED VIA INDIVIDUAL DELIVERY/TASK ORDERS***." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Origin Government 0002 Destination Government Destination Government 0002 0003 Origin Contractor Origin Government 0004 Destination Government Destination Government 0005 Destination Government Destination Government 0006 Origin Government Origin Government 0020 Destination Government Destination Government 0030 N/A N/A N/A N/A 0041 Origin Government 0003 Origin Government 0044 Destination Government Destination Government 0045 Destination Government Destination Government 0050 Destination Government Destination Government 1001 Origin Government Origin Government 1006 Origin Government Origin Government 1020 Destination Government Destination Government 1030 N/A N/A N/A N/A 1041 Origin Government 0004 Origin Government 1046 Origin Government Origin Government 1050 Destination Government Destination Government 2001 Origin Government Origin Government 2006 Origin Government Origin Government 2020 Destination Government Destination Government 2030 N/A N/A N/A N/A 2041 Origin Government 0005 Origin Government 2046 Origin Government Origin Government 2050 Destination Government Destination Government 3001 Origin Government Origin Government 3006 Origin Government Origin Government 3020 Destination Government Destination Government 3030 N/A N/A N/A N/A 3041 Origin Government 0006 Origin Government 3046 Origin Government Origin Government 3050 Destination Government Destination Government 4001 Origin Government Origin Government 4006 Origin Government Origin Government 4020 Destination Government Destination Government 4030 N/A N/A N/A Government 0007 N/A N/A N/A 4041 Origin Government 0008 N/A N/A N/A Origin Government 0009 N/A N/A N/A 4046 Origin Government 1001 Origin Government 4050 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements of the higher1. ANSI/EIA-748 earned Value Management
2. ISO 10007 Quality Management – Guidelines for Configuration Management, Third Edition, 01 March 2017
3. ISO/IEC 12207-level quality standard(s) listed in paragraph2017, Systems and Software Engineering – Software Life Cycle Processes, November 2017 4. ISO/IEC/IEEE 24748-4:2016, Systems and Software Engineering -- Life Cycle Management -- Part 4: Systems Engineering Planning, May 2016
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]TBD." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 1000 N/A N/A N/A N/A 1000AA Destination Government 0003 Destination Government 1000AB Destination Government Destination Government 1100 N/A N/A N/A N/A 1100AA Destination Government 0004 Destination Government 1100AB Destination Government Destination Government 1200 N/A N/A N/A N/A 1200AA Destination Government 0005 Destination Government 1200AB Destination Government Destination Government 1300 N/A N/A N/A N/A 1300AA Destination Government 0006 Destination Government 1300AB Destination Government Destination Government 1400 N/A N/A N/A N/A 1400AA Destination Government 0007 Destination Government 1400AB Destination Government Destination Government 2000 N/A N/A N/A N/A 2000AA Destination Government 0008 Destination Government 2000AB Destination Government Destination Government 2000AC Destination Government Destination Government 2000AD Destination Government Destination Government 2100 N/A N/A N/A N/A 2100AA Destination Government 0009 Destination Government 2100AB Destination Government Destination Government 2200 N/A N/A N/A Government 1001 N/A 2200AA Destination Government Destination Government 1002 2200AB Destination Government Destination Government 2300 N/A N/A N/A N/A 2300AA Destination Government 1003 Destination Government 2300AB Destination Government Destination Government 2400 N/A N/A N/A N/A 2400AA Destination Government 1005 Destination Government 2400AB Destination Government Destination Government 3000 N/A N/A N/A N/A 3000AA Destination Government 1007 Destination Government 3000AB Destination Government Destination Government 3000AC Destination Government Destination Government 3000AD Destination Government Destination Government 3100 N/A N/A N/A Government 2001 N/A 3100AA Destination Government Destination Government 2002 3100AB Destination Government Destination Government 3200 N/A N/A N/A N/A 3200AA Destination Government 2003 Destination Government 3200AB Destination Government Destination Government 3300 N/A N/A N/A N/A 3300AA Destination Government 2005 Destination Government 3300AB Destination Government Destination Government 3400 N/A N/A N/A N/A 3400AA Destination Government 2007 Destination Government 3400AB Destination Government Destination Government 4000 N/A N/A N/A Government 3001 N/A 4000AA Destination Government Destination Government 3002 4000AB Destination Government Destination Government 4000AC Destination Government Destination Government 4000AD Destination Government Destination Government 4100 N/A N/A N/A N/A 4100AA Destination Government 3003 Destination Government 4100AB Destination Government Destination Government 4200 N/A N/A N/A N/A 4200AA Destination Government 3005 Destination Government 4200AB Destination Government Destination Government 4300 N/A N/A N/A N/A 4300AA Destination Government 3007 Destination Government 4300AB Destination Government Destination Government 4400 N/A N/A N/A Government 4001 N/A 4400AA Destination Government Destination Government 4002 4400AB Destination Government Destination Government 5000 N/A N/A N/A N/A 5000AA Destination Government 4003 Destination Government 5000AB Destination Government Destination Government 5000AC Destination Government Destination Government 5000AD Destination Government Destination Government 5100 N/A N/A N/A N/A 5100AA Destination Government 4005 Destination Government 5100AB Destination Government Destination Government 5200 N/A N/A N/A N/A 5200AA Destination Government 4007 Destination Government 5200AB Destination Government Destination Government 5300 N/A N/A N/A N/A 5300AA Destination Government Destination Government 5300AB Destination Government Destination Government 5400 N/A N/A N/A N/A 5400AA Destination Government Destination Government 5400AB Destination Government Destination Government 6000 Destination Government Destination Government 6100 Destination Government Destination Government 6200 Destination Government Destination Government 6300 Destination Government Destination Government 6400 Destination Government Destination Government 7000 Destination Government Destination Government 8000 Destination Government Destination Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018) Inspection and acceptance of all data shall be as specified on the attached Contract Data Requirements List(s), DD Form 1423. CLAUSES INCORPORATED BY FULL TEXT E-246-H016 INSPECTION AND ACCEPTANCE OF F.O.B. DESTINATION DELIVERIES (NAVSEA) (OCT 2018) Item(s) CLIN 1000, 1100, 1200, 1300, 1400, 2000, 2100, 2200, 2300, 2400, 3000, 3100, 3200, 3300, 3400, 4000, acceptance shall be made at destination by a representative of the Government. E-246-H020 QUALITY MANAGEMENT SYSTEM REQUIREMENTS (NAVSEA) (OCT 2018) The Contractor shall provide and maintain a quality management system that, as a minimum, adheres to the requirements of ASQ/ANSI/ISO 9001:2015 “Quality Management Systems – Requirements” and supplemental requirements imposed by this contract. The quality management system procedures, planning, and all other documentation and data that comprise the quality management system shall be made available to the Government for review. Existing quality documents that meet the requirements of this contract may continue to be used. The Government may perform any necessary inspections, verifications, and evaluations to ascertain conformance to requirements and the adequacy of the implementing procedures. The Contractor shall flow down such standards, as applicable, to lower-tier subcontractors under instances covered in FAR 52.246-11 HIGHER11(b) or at the direction of the Contracting Officer. The Government reserves the right to disapprove the quality management system or portions thereof when it fails to meet the contractual requirements. CLAUSES INCORPORATED BY FULL TEXT E-246-LEVEL CONTRACT QUALITY REQUIREMENT H022 INSPECTION AND TEST RECORDS (DEC 2014NAVSEA) (JAN 2019) Inspection and test records shall, as a minimum, indicate the nature of the observations, number of observations made, and the number and type of deficiencies found. Data included in inspection and test records shall be complete and accurate, and shall be used for trend analysis and to assess corrective action and effectiveness. The data shall, on request, be identified and made available for on-site review by the Contracting Officer or designated Government representative. CLAUSES INCORPORATED BY FULL TEXT E-246-W002 CERTIFICATE OF COMPLIANCE (NAVSEA) (OCT 2018)
(a) A certification of material shall be provided by the Contractor, one (1) copy to accompany the shipment (in the packing list envelope) and (l) copy mailed to arrive at time of receipt of the shipment. Mark all certificates to the attention of Code 00Q.
(b) The Contractor certificate shall comply state compliance of material with drawing specification and contract/order requirements. The certificate shall as a minimum state the company name, contract/order number, drawing or specification number, and date. The certificate shall state, above the signature of a legally authorized representative of the company, the following: This certification concerns a matter within the jurisdiction of an agency of the United States and the making of a false, fictitious, or fraudulent certification may render the maker subject to prosecution under Title 18, United States Code, Section 1001.
(c) Failure to provide certification at the time of shipment may result in material being rejected and returned at the contractor's expense.
(d) The certificate shall read as follows: I certify that on [insert date], the [insert Contractor’s name] furnished the supplies called for by the Order/Contract No. via [Carrier] on [identify the bill of lading or shipping document] in accordance with all applicable requirements. I further certify that the supplies or services are of the quality specified and conform in all respects with the highercontract requirements, including specifications, drawings, preservation, packaging, packing, marking requirements, and physical item identification (part number), and are in the quantity shown on this document. Date of Execution: Signature: Typed Name: Title: E-246-W003 INSPECTION STANDARDS (NAVSEA) (OCT 2018) Acceptance inspection of lots or batches will be in accordance with American National Standard ANSI/ASQ Z1.4-2003. Unless otherwise specified, attributes, which if defective would prohibit or reduce the usability of the product for its intended purpose, will be inspected at an acceptable quality level quality standard(s(AQL) listed belowof 1.0. Attributes which do not materially reduce the usability of the product will be inspected at an AQL of 2.5. Any attributes classified as critical on the technical documentation will be inspected on each unit of product submitted. The right is reserved to reject any unit of product found nonconforming during inspection whether that unit of product forms a part of a sample or not, and whether the lot or batch as a whole is accepted or rejected. E-246-W004 PROCUREMENT QUALITY ASSURANCE INSPECTION AND ACCEPTANCE (NAVSEA) (OCT 2018)
(a) Initial inspection of the supplies to be furnished hereunder shall be made by TBD at contract award at the contractor's or subcontractor's plant located at TBD at contract award. The contractor shall notify the cognizant inspector when the material is available for inspection. The place designated for such inspections shall not be changed without authorization of the Contracting Officer. Final inspection and acceptance shall be made by NSWC PHD within 30 days after receipt.
(b) The Contractor Initial inspection shall include applicable requirements consist of quality assurance at point of manufacture or assembly and check/test prior to shipment. Final inspection and acceptance will be made by the Receiving Activity after installation/check out/testing of the higher-level quality standard(s) listed in paragraphsupplies.
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]TBD." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 1000 N/A N/A N/A N/A 1000AA Destination Government Destination Government 0002 1000AB Destination Government Destination Government 1000AC Destination Government Destination Government 1000AD Destination Government Destination Government 1100 N/A N/A N/A N/A 1100AA Destination Government Destination Government 1200 N/A N/A N/A N/A 1200AA Destination Government Destination Government 1300 N/A N/A N/A N/A 1300AA Destination Government Destination Government 1400 N/A N/A N/A N/A 1400AA Destination Government Destination Government 2000 N/A N/A N/A N/A 2000AA Destination Government Destination Government 2000AB Destination Government Destination Government 2000AC Destination Government Destination Government 2000AD Destination Government Destination Government 2100 N/A N/A N/A N/A 2100AA Destination Government Destination Government 2200 N/A N/A N/A N/A 2200AA Destination Government Destination Government 2300 N/A N/A N/A N/A 2300AA Destination Government Destination Government 2400 N/A N/A N/A N/A 2400AA Destination Government Destination Government 3000 N/A N/A N/A N/A 3000AA Destination Government Destination Government 3000AB Destination Government Destination Government 3000AC Destination Government Destination Government 3000AD Destination Government Destination Government 3000AE Destination Government Destination Government 3100 N/A N/A N/A N/A 3100AA Destination Government Destination Government 3200 N/A N/A N/A N/A 3200AA Destination Government Destination Government 3300 N/A N/A N/A N/A 3300AA Destination Government Destination Government 3400 N/A N/A N/A N/A 3400AA Destination Government Destination Government 4000 N/A N/A N/A N/A 4000AA Destination Government Destination Government 4000AB Destination Government Destination Government 4000AC Destination Government Destination Government 4000AD Destination Government Destination Government 4000AE Destination Government Destination Government 4000AF Destination Government Destination Government 5000 N/A N/A N/A N/A 5000AA Destination Government Destination Government 5000AB Destination Government Destination Government 5000AC Destination Government Destination Government 5000AD Destination Government Destination Government 5000AE Destination Government Destination Government 6100 N/A N/A N/A N/A 6100AA Destination Government Destination Government 6200 N/A N/A N/A N/A 6200AA Destination Government Destination Government 6300 N/A N/A N/A N/A 6300AA Destination Government Destination Government 6400 N/A N/A N/A N/A 6400AA Destination Government Destination Government 7000 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 7100 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 7200 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 7300 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 7400 Destination Government Destination Government 4002 N/A N/A N/A 8000 Destination Government 4003 N/A N/A N/A Destination Government 4005 N/A N/A N/A Government 4007 9999 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.. ANSI/ASQC Q9001 or ISO 9001
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]TBD." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 1000 N/A N/A N/A N/A 1000AA Origin Government Origin Government 1000AB Origin Government Origin Government 1000AC Origin Government Origin Government 1000AD Origin Government Origin Government 1100 N/A N/A N/A N/A 1100AA Destination Government Destination Government 0002 1200 N/A N/A N/A N/A 1200AA Destination Government Destination Government 1300 N/A N/A N/A N/A 1300AA Destination Government Destination Government 1400 N/A N/A N/A N/A 1400AA Destination Government Destination Government 2000 N/A N/A N/A N/A 2000AA Destination Government Destination Government 2000AB Destination Government Destination Government 2000AC Destination Government Destination Government 2000AD Destination Government Destination Government 2100 N/A N/A N/A N/A 2100AA Destination Government Destination Government 2200 N/A N/A N/A N/A 2200AA Destination Government Destination Government 2300 N/A N/A N/A N/A 2300AA Destination Government Destination Government 2400 N/A N/A N/A N/A 2400AA Destination Government Destination Government 3000 N/A N/A N/A N/A 3000AA Destination Government Destination Government 3000AB Destination Government Destination Government 3000AC Destination Government Destination Government 3000AD Destination Government Destination Government 3000AE Destination Government Destination Government 3100 N/A N/A N/A N/A 3100AA Destination Government Destination Government 3200 N/A N/A N/A N/A 3200AA Destination Government Destination Government 3300 N/A N/A N/A N/A 3300AA Destination Government Destination Government 3400 N/A N/A N/A N/A 3400AA Destination Government Destination Government 4000 N/A N/A N/A N/A 4000AA Destination Government Destination Government 4000AB Destination Government Destination Government 4000AC Destination Government Destination Government 4000AD Destination Government Destination Government 4000AE Destination Government Destination Government 4000AF Destination Government Destination Government 5000 N/A N/A N/A N/A 5000AA Destination Government Destination Government 5000AB Destination Government Destination Government 5000AC Destination Government Destination Government 5000AD Destination Government Destination Government 5000AE Destination Government Destination Government 6100 N/A N/A N/A N/A 6100AA Destination Government Destination Government 6200 N/A N/A N/A N/A 6200AA Destination Government Destination Government 6300 N/A N/A N/A N/A 6300AA Destination Government Destination Government 6400 N/A N/A N/A N/A 6400AA Destination Government Destination Government 7000 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 7100 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 7200 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 7300 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 7400 Destination Government Destination Government 4002 N/A N/A N/A 8000 Destination Government 4003 N/A N/A N/A Destination Government 4005 N/A N/A N/A Government 4007 9999 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.. ANSI/ASQC Q9001 or ISO 9001
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
(a) of this clause and the requirement to flow down such standards, as applicable, to lower-tier subcontracts, in--
(1) Any subcontract for critical and complex items (see 46.203(b) and (c)); or
(2) When the technical requirements of a subcontract require--
Appears in 1 contract
Sources: Solicitation, Offer and Award
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247HQ D-2-W001 0008 MARKING OF REPORTS (NAVSEA) (SEP 1990) All reports delivered by the Contractor to the Government under this contract shall prominently show on the cover of the report:
(1) name and business address of the Contractor
(2) contract number
(3) contract dollar amount
(4) whether the contract was competitively or non-competitively awarded
(5) sponsor: (Name of Individual Sponsor) (Name of Requiring Activity) (City and State) UW D-2-0001 MARK FOR INFORMATION (AUG 2017)
(a) The Contractor shall include the following “Mark For” information clearly marked on all packages (or items themselves if they are not packaged) delivered under this contract/order: Mark For: TO BE FILLED IN AT ORDER LEVEL
(b) The Contractor shall also include in each package delivered (or affixed to the item itself if it is not packaged) a packing slip which lists the items included by Contract Line Item Number (e.g., CLIN 0001, 0002). UW D-2-0002 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018MAR 2017) The use of asbestos, excelsior, newspaper newspaper, or shredded paper (all types including waxed paper, computer paper paper, and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose loose fill polystyrene is prohibited for shipboard use. D-247UW D-2-W002 0003 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018MAR 2017)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award](state where located)." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [Contractor to be completed at awardfill in]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Origin Government 0002 Origin Government Origin Government 0003 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246E-246-11 HIGHERH013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018) Inspection and acceptance of all data shall be as specified on the attached Contract Data Requirements List(s), DD Form 1423. CLAUSES INCORPORATED BY FULL TEXT E-246-LEVEL CONTRACT QUALITY REQUIREMENT H017 INSPECTION AND ACCEPTANCE OF F.O.B. ORIGIN DELIVERIES (DEC 2014)
NAVSEA) (aOCT 2018) E-246-H022 INSPECTION AND TEST RECORDS (NAVSEA) (JAN 2019) Inspection and test records shall, as a minimum, indicate the nature of the observations, number of observations made, and the number and type of deficiencies found. Data included in inspection and test records shall be complete and accurate, and shall be used for trend analysis and to assess corrective action and effectiveness. The data shall, on request, be identified and made available for on-site review by the Contracting Officer or designated Government representative. E-246-W007 NOTIFICATION OF INSPECTION OR TEST (NAVSEA) (OCT 2018) The Contractor shall comply with agrees to notify the higherTPOC identified in Section G, in writing, when the material will be inspected and/or tested. A minimum of 10 business days is required to arrange such a visit. Section F - Deliveries or Performance CLAUSES INCORPORATED BY REFERENCE 52.211-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements 17 Delivery of the higherExcess Quantities SEP 1989 52.242-level quality standard(s) listed in paragraph15 Stop-Work Order AUG 1989 52.242-17 Government Delay Of Work APR 1984 52.247-29 F.O.B. Origin FEB 2006 52.247-34 F.O.B. Destination NOV 1991 52.247-48 F.O.B. Destination--Evidence Of Shipment FEB 1999 CLAUSES INCORPORATED BY FULL TEXT
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- CAUTION-THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at awardinsert location]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED on the top of the box [to be completed at awardinsert location]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination N/A N/A N/A N/A 0001AA Origin Government Destination Government 0002 N/A N/A N/A N/A 0002AA Origin Government Destination Government 0003 N/A N/A N/A N/A 0003AA Origin Government Destination Government 0004 N/A N/A N/A N/A 0004AA Origin Government Destination Government 0005 N/A N/A N/A N/A 0005AA Origin Government Destination Government 0006 N/A N/A N/A N/A 0006AA Origin Government Destination Government 0007 N/A N/A N/A N/A 0007AA Origin Government Destination Government 0008 N/A N/A N/A N/A 0008AA Origin Government Destination Government 0009 N/A N/A N/A Government 1001 Destination N/A 0009AA Origin Government Destination Government 1002 0010 N/A N/A N/A N/A 0010AA Origin Government 1003 Destination Government 0011 N/A N/A N/A N/A 0011AA Origin Government 1005 Destination Government 0012 N/A N/A N/A N/A 0012AA Origin Government 1007 Destination Government 0013 N/A N/A N/A Government 2001 Destination N/A 0013AA Origin Government Destination Government 2002 0014 N/A N/A N/A N/A 0014AA Origin Government 2003 Destination Government 0015 N/A N/A N/A N/A 0015AA Origin Government 2005 Destination Government 0016 N/A N/A N/A N/A 0016AA Origin Government 2007 Destination Government 0016AB Origin Government Destination Government 0016AC Origin Government Destination Government 0016AD Origin Government Destination Government 0016AE Origin Government Destination Government 0017 N/A N/A N/A Government 3001 Destination N/A 0017AA Origin Government Destination Government 3002 0017AB Origin Government Destination Government 0017AC Origin Government Destination Government 0018 N/A N/A N/A N/A 0018AA Origin Government 3003 Destination Government 0018AB Origin Government Destination Government 0019 N/A N/A N/A N/A 0019AA Origin Government 3005 Destination Government 0019AB Origin Government Destination Government 0020 N/A N/A N/A N/A 0020AA Origin Government 3007 Destination Government 0020AB Origin Government Destination Government 0021 N/A N/A N/A Government 4001 Destination N/A 0021AA Origin Government Destination Government 4002 0022 N/A N/A N/A N/A 0022AA Origin Government 4003 Destination Government 0023 N/A N/A N/A N/A 0023AA Origin Government 4005 Destination Government 0024 N/A N/A N/A N/A 0024AA Origin Government 4007 Destination Government 0025 N/A N/A N/A N/A 0025AA Origin Government Destination Government 0026 N/A N/A N/A N/A 0026AA Origin Government Destination Government 0027 N/A N/A N/A N/A 0027AA Origin Government Destination Government 0028 N/A N/A N/A N/A 0028AA Origin Government Destination Government 0029 N/A N/A N/A N/A 0029AA Origin Government Destination Government 0030 N/A N/A N/A N/A 0030AA Origin Government Destination Government 0031 N/A N/A N/A N/A 0031AA Origin Government Destination Government 0032 N/A N/A N/A N/A 0032AA Origin Government Destination Government 0033 N/A N/A N/A N/A 0033AA Origin Government Destination Government 0034 Origin Government Destination Government 0035 Origin Government Destination Government 0036 Origin Government Destination Government 0037 Origin Government Destination Government 0038 Origin Government Destination Government 0039 Origin Government Destination Government 0040 Destination Government Destination Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.. ANSI/ASQC Q9001 or ISO 9001
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
(a) of this clause and the requirement to flow down such standards, as applicable, to lower-tier subcontracts, in--
(1) Any subcontract for critical and complex items (see 46.203(b) and (c)); or
(2) When the technical requirements of a subcontract require--
(i) Control of such things as design, work operations, in-process control, testing, and inspection; or
(ii) Attention to such factors as organization, planning, work instructions, documentation control, and advanced metrology. (End of clause) CLAUSES INCORPORATED BY FULL TEXT E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018) Inspection and acceptance of all data shall be as specified on the attached Contract Data Requirements List(s), DD Form 1423. CLAUSES INCORPORATED BY FULL TEXT E-246-H020 QUALITY MANAGEMENT SYSTEM REQUIREMENTS (NAVSEA) (OCT 2018) The Contractor shall provide and maintain a quality management system that, as a minimum, adheres to the requirements of ASQ/ANSI/ISO 9001:2015 “Quality Management Systems – Requirements” and supplemental requirements imposed by this contract. The quality management system procedures, planning, and all other documentation and data that comprise the quality management system shall be made available to the Government for review. Existing quality documents that meet the requirements of this contract may continue to be used. The Government may perform any necessary inspections, verifications, and evaluations to ascertain conformance to requirements and the adequacy of the implementing procedures. The Contractor shall flow down such standards, as applicable, to lower-tier subcontractors under instances covered in FAR 52.246-11(b) or at the direction of the Contracting Officer. The Government reserves the right to disapprove the quality management system or portions thereof when it fails to meet the contractual requirements. E-246-H021 COST DATA FOR QUALITY MANAGEMENT SYSTEM (NAVSEA) (JAN 2019) The contractor shall maintain and use cost data as a management element of the Quality Management System. The specific cost data to be maintained and used will be determined by the contractor. The data shall, on request, be identified and made available for on-site review by the Contracting Officer or designated Government representative. CLAUSES INCORPORATED BY FULL TEXT E-246-H022 INSPECTION AND TEST RECORDS (NAVSEA) (JAN 2019) Inspection and test records shall, as a minimum, indicate the nature of the observations, number of observations made, and the number and type of deficiencies found. Data included in inspection and test records shall be complete and accurate, and shall be used for trend analysis and to assess corrective action and effectiveness. The data shall, on request, be identified and made available for on-site review by the Contracting Officer or designated Government representative. CLAUSES INCORPORATED BY FULL TEXT E-246-W002 CERTIFICATE OF COMPLIANCE (NAVSEA) (OCT 2018)
(a) A certification of material shall be provided by the Contractor, one (1) copy to accompany the shipment (in the packing list envelope) and (l) copy mailed to arrive at time of receipt of the shipment. Mark all certificates to the attention of Code 00Q.
(b) The certificate shall state compliance of material with drawing specification and contract/order requirements. The certificate shall as a minimum state the company name, contract/order number, drawing or specification number, and date. The certificate shall state, above the signature of a legally authorized representative of the company, the following: This certification concerns a matter within the jurisdiction of an agency of the United States and the making of a false, fictitious, or fraudulent certification may render the maker subject to prosecution under Title 18, United States Code, Section 1001.
(c) Failure to provide certification at the time of shipment may result in material being rejected and returned at the contractor's expense.
(d) The certificate shall read as follows: I certify that on [insert date], the [insert Contractor’s name] furnished the supplies called for by the Order/Contract No. via [Carrier] on [identify the bill of lading or shipping document] in accordance with all applicable requirements. I further certify that the supplies or services are of the quality specified and conform in all respects with the contract requirements, including specifications, drawings, preservation, packaging, packing, marking requirements, and physical item identification (part number), and are in the quantity shown on this document.
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEANAVSEA ) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will themwill be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]TBD." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 1000 N/A N/A N/A N/A 1000AA Destination Government 0003 Destination Government 1000AB Destination Government Destination Government 1100 N/A N/A N/A N/A 1100AA Destination Government 0004 Destination Government 1100AB Destination Government Destination Government 1200 N/A N/A N/A N/A 1200AA Destination Government 0005 Destination Government 1200AB Destination Government Destination Government 1300 N/A N/A N/A N/A 1300AA Destination Government 0006 Destination Government 1300AB Destination Government Destination Government 1400 N/A N/A N/A N/A 1400AA Destination Government 0007 Destination Government 1400AB Destination Government Destination Government 2000 N/A N/A N/A N/A 2000AA Destination Government 0008 Destination Government 2000AB Destination Government Destination Government 2000AC Destination Government Destination Government 2000AD Destination Government Destination Government 2100 N/A N/A N/A N/A 2100AA Destination Government 0009 Destination Government 2100AB Destination Government Destination Government 2200 N/A N/A N/A Government 1001 N/A 2200AA Destination Government Destination Government 1002 2200AB Destination Government Destination Government 2300 N/A N/A N/A N/A 2300AA Destination Government 1003 Destination Government 2300AB Destination Government Destination Government 2400 N/A N/A N/A N/A 2400AA Destination Government 1005 Destination Government 2400AB Destination Government Destination Government 3000 N/A N/A N/A N/A 3000AA Destination Government 1007 Destination Government 3000AB Destination Government Destination Government 3000AC Destination Government Destination Government 3000AD Destination Government Destination Government 3100 N/A N/A N/A Government 2001 N/A 3100AA Destination Government Destination Government 2002 3100AB Destination Government Destination Government 3200 N/A N/A N/A N/A 3200AA Destination Government 2003 Destination Government 3200AB Destination Government Destination Government 3300 N/A N/A N/A N/A 3300AA Destination Government 2005 Destination Government 3300AB Destination Government Destination Government 3400 N/A N/A N/A N/A 3400AA Destination Government 2007 Destination Government 3400AB Destination Government Destination Government 4000 N/A N/A N/A Government 3001 N/A 4000AA Destination Government Destination Government 3002 4000AB Destination Government Destination Government 4000AC Destination Government Destination Government 4000AD Destination Government Destination Government 4100 N/A N/A N/A N/A 4100AA Destination Government 3003 Destination Government 4100AB Destination Government Destination Government 4200 N/A N/A N/A N/A 4200AA Destination Government 3005 Destination Government 4200AB Destination Government Destination Government 4300 N/A N/A N/A N/A 4300AA Destination Government 3007 Destination Government 4300AB Destination Government Destination Government 4400 N/A N/A N/A Government 4001 N/A 4400AA Destination Government Destination Government 4002 4400AB Destination Government Destination Government 5000 N/A N/A N/A N/A 5000AA Destination Government 4003 Destination Government 5000AB Destination Government Destination Government 5000AC Destination Government Destination Government 5000AD Destination Government Destination Government 5100 N/A N/A N/A N/A 5100AA Destination Government 4005 Destination Government 5100AB Destination Government Destination Government 5200 N/A N/A N/A N/A 5200AA Destination Government 4007 Destination Government 5200AB Destination Government Destination Government 5300 N/A N/A N/A N/A 5300AA Destination Government Destination Government 5300AB Destination Government Destination Government 5400 N/A N/A N/A N/A 5400AA Destination Government Destination Government 5400AB Destination Government Destination Government 6000 Destination Government Destination Government 6100 Destination Government Destination Government 6200 Destination Government Destination Government 6300 Destination Government Destination Government 6400 Destination Government Destination Government 7000 Destination Government Destination Government 8000 Destination Government Destination Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018) Inspection and acceptance of all data shall be as specified on the attached Contract Data Requirements List(s), DD Form 1423. CLAUSES INCORPORATED BY FULL TEXT E-246-H016 INSPECTION AND ACCEPTANCE OF F.O.B. DESTINATION DELIVERIES (NAVSEA) (OCT 2018) Item(s) CLIN 1000, 1100, 1200, 1300, 1400, 2000, 2100, 2200, 2300, 2400, 3000, 3100, 3200, 3300, 3400, 4000, acceptance shall be made at destination by a representative of the Government. E-246-H020 QUALITY MANAGEMENT SYSTEM REQUIREM ENTS (NAVSEA) (OCT 2018) The Contractor shall provide and maintain a quality management systemthat, as a minimum, adheres to the requirements of ASQ/ANSI/ISO 9001:2015 “Quality Management Systems – Requirements” and supplemental requirements imposed by this contract. The quality management systemprocedures, planning, and all other documentation and data that comprise the quality management systemshall be made available to the Government for review. Existing quality documents that meet the requirements of this contract may continue to be used. The Government may perform any necessary inspections, verifications, and evaluations to ascertain conformance to requirements and the adequacy of the implementing procedures. The Contractor shall flow down such standards, as applicable, to lower-tier subcontractors under instances covered in FAR 52.246-11 HIGHER11(b) or at the direction of the Contracting Officer. The Government reserves the right to disapprove the quality management systemor portions thereof when it fails to meet the contractual requirements. CLAUSES INCORPORATED BY FULL TEXT E-246-LEVEL CONTRACT QUALITY REQUIREMENT H022 INSPECTION AND TEST RECORDS (DEC 2014NAVSEA) (JAN 2019) Inspection and test records shall, as a minimum, indicate the nature of the observations, number of observations made, and the number and type of deficiencies found. Data included in inspection and test records shall be complete and accurate, and shall be used for trend analysis and to assess corrective action and effectiveness. The data shall, on request, be identified and made available for on-site review by the Contracting Officer or designated Government representative. CLAUSES INCORPORATED BY FULL TEXT E-246-W002 CERTIFICATE OF COMPLIANCE (NAVSEA) (OCT 2018)
(a) A certification of material shall be provided by the Contractor, one (1) copy to accompany the shipment (in the packing list envelope) and (l) copy mailed to arrive at time of receipt of the shipment. Mark all certificates to the attention of Code 00Q.
(b) The Contractor certificate shall comply state compliance of material with drawing specification and contract/order requirements. The certificate shall as a minimum state the company name, contract/order number, drawing or specification number, and date. The certificate shall state, above the signature of a legally authorized representative of the company, the following: This certification concerns a matter within the jurisdiction of an agency of the United States and the making of a false, fictitious, or fraudulent certification may render the maker subject to prosecution under Title 18, United States Code, Section 1001.
(c) Failure to provide certification at the time of shipment may result in material being rejected and returned at the contractor's expense.
(d) The certificate shall read as follows: I certify that on ______ [insert date], the [insert Contractor’s name] furnished the supplies called for by the Order/Contract No._____ via ____ [Carrier] on [identify the bill of lading or shipping document] in accordance with all applicable requirements. I further certify that the supplies or services are of the quality specified and conform in all respects with the highercontract requirements, including specifications, drawings, preservation, packaging, packing, marking requirements, and physical item identification (part number), and are in the quantity shown on this document. Date of Execution: __________ _ _ _ _ __ _ _ Signature: ___________ _ _ _ _ _ _ _ _ __ Typed Name: ___________ _ _ _ _ _ _ _ __ Title: __________ E-246-W003 INSPECTION STANDARDS (NAVSEA) (OCT 2018) Acceptance inspection of lots or batches will be in accordance with American National Standard ANSI/ASQ Z1.4-2003. Unless otherwise specified, attributes, which if defective would prohibit or reduce the usability of the product for its intended purpose, will be inspected at an acceptable quality level quality standard(s(AQL) listed belowof 1.0. Attributes which do not materially reduce the usability of the product will be inspected at an AQL of 2.5. Any attributes classified as critical on the technical documentation will be inspected on each unit of product submitted. The right is reserved to reject any unit of product found nonconforming during inspection whether that unit of product forms a part of a sample or not, and whether the lot or batch as a whole is accepted or rejected. E-246-W004 PROCUREM ENT QUALITY ASSURANCE INSPECTION AND ACCEPTANCE (NAVSEA) (OCT 2018)
(a) Initial inspection of the supplies to be furnished hereunder shall be made by TBD at contract award at the contractor's or subcontractor's plant located at TBD at contract award. The contractor shall notify the cognizant inspector when the material is available for inspection. The place designated for such inspections shall not be changed without authorization of the Contracting Officer. Final inspection and acceptance shall be made by NSWC PHD within 30 days after receipt.
(b) The Contractor Initial inspection shall include applicable requirements consist of quality assurance at point of manufacture or assembly and check/test prior to shipment. Final inspection and acceptance will be made by the Receiving Activity after installation/check out/testing of the higher-level quality standard(s) listed in paragraphsupplies.
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at awardinsert location]." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 0003 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246E-246-11 HIGHERH016 INSPECTION AND ACCEPTANCE OF F.O.B. DESTINATION DELIVERIES (NAVSEA) (OCT 2018) Item(s) 0001 - 0003 - Inspection and acceptance shall be made at destination by a representative of the Government. E-246-LEVEL CONTRACT QUALITY REQUIREMENT H022 INSPECTION AND TEST RECORDS (DEC 2014NAVSEA) (JAN 2019) Inspection and test records shall, as a minimum, indicate the nature of the observations, number of observations made, and the number and type of deficiencies found. Data included in inspection and test records shall be complete and accurate, and shall be used for trend analysis and to assess corrective action and effectiveness. The data shall, on request, be identified and made available for on-site review by the Contracting Officer or designated Government representative. E-246-W002 CERTIFICATE OF COMPLIANCE (NAVSEA) (OCT 2018)
(a) The Contractor A certification of material shall comply with be provided by the higher-level quality standard(sContractor, one (1) listed below.copy to accompany the shipment (in the packing list envelope) and (l) copy mailed to arrive at time of receipt of the shipment. Mark all certificates to the attention of Code 00Q.
(b) The Contractor certificate shall include applicable requirements state compliance of material with drawing specification and contract/order requirements. The certificate shall as a minimum state the company name, contract/order number, drawing or specification number, and date. The certificate shall state, above the signature of a legally authorized representative of the higher-level company, the following: This certification concerns a matter within the jurisdiction of an agency of the United States and the making of a false, fictitious, or fraudulent certification may render the maker subject to prosecution under Title 18, United States Code, Section 1001.
(c) Failure to provide certification at the time of shipment may result in material being rejected and returned at the contractor's expense.
(d) The certificate shall read as follows: I certify that on [insert date], the [insert Contractor’s name] furnished the supplies called for by the Order/Contract No. via [Carrier] on [identify the bill of lading or shipping document] in accordance with all applicable requirements. I further certify that the supplies or services are of the quality standard(s) listed specified and conform in paragraphall respects with the contract requirements, including specifications, drawings, preservation, packaging, packing, marking requirements, and physical item identification (part number), and are in the quantity shown on this document.
Appears in 1 contract
Sources: Solicitation, Offer and Award
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247All reports delivered by the Contractor to the Government under this contract shall prominently show on the cover of the report:
(1) name and business address of the Contractor
(2) contract number
(3) contract dollar amount
(4) whether the contract was competitively or non-W001 PROHIBITED PACKING MATERIALS competitively awarded
(NAVSEA5) sponsor: (Name of Individual Sponsor) (OCT 2018Name of Requiring Activity) (City and State)
(a) The Contractor shall include the following “Mark For” information clearly marked on all packages (or items themselves if they are not packaged) delivered under this contract/order: Receiving Officer, Naval Station Newport ▇▇ ▇▇▇▇▇▇▇▇ ▇▇▇▇▇▇ Newport, RI 02841-1716 Mark For: NUWC Division, Newport Contract #: N66604-TBD Attn: TBD The use of asbestos, excelsior, newspaper newspaper, or shredded paper (all types including waxed paper, computer paper paper, and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018).
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award](state where located)." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 1 contract
Sources: Contract
Part Identification. All items within the kit, set, installation hardware or material shall be suitably segregated and identified within the unit pack(s) or shipping container by part number and/or national stock number. Refer to the above cited MIL-STD for marking of assorted (related-unrelated) items. D-247-W001 PROHIBITED PACKING MATERIALS (NAVSEA) (OCT 2018) The use of asbestos, excelsior, newspaper or shredded paper (all types including waxed paper, computer paper and similar hygroscopic or non-neutral material) is prohibited. In addition, the use of yellow wrapping or packaging material is prohibited except where used for the containment of radioactive material. Loose fill polystyrene is prohibited for shipboard use. D-247-W002 UNPACKING INSTRUCTIONS (NAVSEA) (OCT 2018)
(a) Location on Container. When practical, one set of the unpacking instructions will be placed in a heavy water-proof envelope prominently marked "UNPACKING INFORMATION" and firmly affixed to the outside of the shipping container in a protected location, preferably between the cleats on the end of the container adjacent to the identification marking. If the instructions cover a set of equipment packed in multiple containers, the instructions will be affixed to the number one container of the set. When the unpacking instructions are too voluminous to be affixed to the exterior of the container, they will be placed inside and directions for locating them will be provided in the envelope marked "UNPACKING INFORMATION".
(b) Marking Containers. When unpacking instructions are provided, shipping containers will be stenciled "CAUTION- THIS EQUIPMENT MAY BE SERIOUSLY DAMAGED UNLESS UNPACKING INSTRUCTIONS ARE CAREFULLY FOLLOWED. UNPACKING INSTRUCTIONS ARE LOCATED [to be completed at award]TBD." When practical, this marking will be applied adjacent to the identification marking on the side of the container. Section E - Inspection and Acceptance Section E - Inspection and Acceptance Inspection and acceptance of all data shall be in accordance in E-246-H013 INSPECTION AND ACCEPTANCE OF DATA (NAVSEA) (OCT 2018). INSPECTION AND ACCEPTANCE Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Origin Government Destination Government 0002 Origin Government Destination Government 0003 Origin Government Origin Government 0004 Origin Government Destination Government 0005 Origin Government Destination Government 0006 Origin Government Destination Government 0007 Origin Government Origin Government 0008 Destination Government Destination Government 0009 Destination Government Destination Government 1001 Origin Government Destination Government 1002 Origin Government Destination Government 1003 Origin Government Origin Government 1005 Origin Government Destination Government 1007 Origin Government Origin Government 2001 Origin Government Destination Government 2002 Origin Government Destination Government 2003 Origin Government Origin Government 2005 Origin Government Destination Government 2007 Origin Government Origin Government 3001 Origin Government Destination Government 3002 Origin Government Destination Government 3003 Origin Government Origin Government 3005 Origin Government Destination Government 3007 Origin Government Origin Government 4001 Origin Government Destination Government 4002 Origin Government Destination Government 4003 Origin Government Origin Government 4005 Origin Government Destination Government 4007 Origin Government Origin Government INSPECTION AND ACCEPTANCE TERMS Supplies/services will be inspected/accepted at: ▇▇▇▇ INSPECT AT INSPECT BY ACCEPT AT ACCEPT BY 0001 Destination Government Destination Government 0002 N/A N/A N/A Government 0003 N/A N/A N/A Government 0004 N/A N/A N/A Government 0005 N/A N/A N/A Government 0006 N/A N/A N/A Government 0007 N/A N/A N/A Government 0008 N/A N/A N/A Government 0009 N/A N/A N/A Government 1001 Destination Government Destination Government 1002 N/A N/A N/A Government 1003 N/A N/A N/A Government 1005 N/A N/A N/A Government 1007 N/A N/A N/A Government 2001 Destination Government Destination Government 2002 N/A N/A N/A Government 2003 N/A N/A N/A Government 2005 N/A N/A N/A Government 2007 N/A N/A N/A Government 3001 Destination Government Destination Government 3002 N/A N/A N/A Government 3003 N/A N/A N/A Government 3005 N/A N/A N/A Government 3007 N/A N/A N/A Government 4001 Destination Government Destination Government 4002 N/A N/A N/A Government 4003 N/A N/A N/A Government 4005 N/A N/A N/A Government 4007 N/A N/A N/A Government CLAUSES INCORPORATED BY REFERENCE 52.246-2 Inspection Of Supplies--Fixed Price AUG 1996 52.246-3 Inspection Of Supplies Cost-Reimbursement MAY 2001 52.246-5 Inspection Of Services Cost-Reimbursement APR 1984 52.246-15 Certificate of Conformance APR 1984 52.246-16 Responsibility For Supplies APR 1984 CLAUSES INCORPORATED BY FULL TEXT 52.246-11 HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT (DEC 2014)
(a) The Contractor shall comply with the higher-level quality standard(s) listed below.
(b) The Contractor shall include applicable requirements of the higher-level quality standard(s) listed in paragraph
Appears in 1 contract
Sources: Contract