Common use of Markings Clause in Contracts

Markings. Rear fog lamps submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating: (a) The category or categories of light source prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above. 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear The samples of a type of rear fog lamps lamp submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating: (a) The category or categories of light source prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above. 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltagevoltage and rated maximum wattage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.14.3.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltagevoltage and rated maximum wattage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating: (a) The category or categories of light source prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above. 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog Cornering lamps submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above.; 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-non- replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must shall be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 44.3. 3.1.11.1. below and, in the case several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltage. 3.6. Lamps operating at voltages other than the nominal rated voltages of 6 V, 12 V or 24 V respectively, by the application of an electronic light source control gear being not part of the lamp, shall also bear a marking denoting the rated secondary design voltage. 3.7. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog Daytime running lamps submitted for approval shall: 3.14.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and be indelible; 3.24.2. With the exception of daytime running lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above. 3.4. In the case of daytime running lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.54.4. Provide adequate space for the approval mark and for the additional symbols prescribed in paragraph 5.2. below; the said space shall be shown in the drawings referred to in paragraph 3.2.1. above. 4.5. In the case of daytime running lamps with light source module(s), the light source module(s) shall bear: 3.5.14.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and indelible; 3.5.24.5.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 45. 3.1.12.1.1. below and, in the case several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.13. 2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.34.5.3. The marking of the rated voltage or range of voltage. 3.64.6. Lamps operating at voltages other than the nominal rated voltages of 6 V, 12 V or 24 V respectively, by the application of an electronic light source control gear being not part of the lamp, must also bear a marking denoting the rated secondary design voltage. 4.7. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps The samples of a type of reversing lamp or manoeuvring lamp submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. If necessary, in order to prevent any mistake in mounting the reversing lamp on the vehicle, bear the word "TOP" marked horizontally on the uppermost part of the illuminating surface; 3.4. Provide adequate space for the approval ▇▇▇▇ and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings drawing referred to in paragraph 2.2.1. above.; 3.43.5. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or or light source module(s), bear the marking of the rated voltage or the range of voltage.voltage and the rated wattage; 3.53.6. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.13.6.1. The trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and indelible; 3.5.23.6.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.14.3.1.1. below and, in the case of several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.33.6.3. The marking of the rated voltage or range of voltageand rated wattage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps Devices submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source filament lamp(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate Comprise a space of sufficient size for the approval ▇▇▇▇ marking and for the additional symbols prescribed in paragraph 4.34.2. below; the said this space shall be shown in the drawings referred to mentioned in paragraph 2.2.1. above.; 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltagevoltage and rated maximum wattage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.12.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltagevoltage and rated maximum wattage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear The samples of a type of rear fog lamps lamp submitted for approval shall: 3.1. Bear bear the trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and be indelible; 3.2. With with the exception of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating: (a) The : - the category or categories of light source filament lamp prescribed; and/or (b) The and/or - the light source module specific identification code. 3.3. Provide provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above. 3.4. In in the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or or light source module(s), bear the marking of the rated voltage or range of voltageand rated wattage. 3.5. In in the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The the trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and indelible; 3.5.2. The the specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or charactersbelow; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.12. 2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The the marking of the rated voltage or range of voltageand rated wattage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps The samples of a type of cornering lamp submitted for approval shall: 3.1. Bear bear the trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With with the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The : - the category or categories of light source filament lamp(s) prescribed; and/or (b) The and/or - the light source module specific identification code. 3.3. Provide provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above.; 3.4. In in the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or or light source module(s), bear the marking of the rated voltage or range of voltageand rated wattage. 3.5. In in the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The the trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and indelible; 3.5.2. The the specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or charactersbelow; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.12. 2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The the marking of the rated voltage or range of voltageand rated wattage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps The samples of a type of cornering lamp submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above.; 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltagevoltage and rated maximum wattage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must shall be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.14.3.1.1. below and, in the case several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage and rated wattage. 3.6. Lamps operating at voltages other than the nominal rated voltages of 6 V, 12 V or range 24 V respectively, by the application of an electronic light source control gear being not part of the lamp, shall also bear a marking denoting the rated secondary design voltage. 3.63.7. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps The samples of a type of reversing lamp or manoeuvring lamp submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. If necessary, in order to prevent any mistake in mounting the reversing lamp on the vehicle, bear the word "TOP" marked horizontally on the uppermost part of the illuminating surface; 3.4. Provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings drawing referred to in paragraph 2.2.1. above.; 3.43.5. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or or light source module(s), bear the marking of the rated voltage or the range of voltage.voltage and the rated wattage; 3.53.6. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.13.6.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and indelible; 3.5.23.6.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.14.3.1.1. below and, in the case of several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.33.6.3. The marking of the rated voltage or range of voltageand rated wattage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps Devices submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate Comprise a space of sufficient size for the approval ▇▇▇▇ marking and for the additional symbols prescribed in paragraph 4.34.2. below; the said this space shall be shown in the drawings referred to mentioned in paragraph 2.2.1. above.; 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltagevoltage and rated maximum wattage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ of the applicant; this marking must shall be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must shall be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.12.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltagevoltage and rated maximum wattage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear The samples of a type of rear fog lamps lamp submitted for approval shall: 3.1. Bear bear the trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and be indelible; 3.2. With with the exception of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating: (a) The : - the category or categories of light source filament lamp prescribed; and/or (b) The and/or - the light source module specific identification code. 3.3. Provide provide adequate space for the approval ▇▇▇▇ and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above. 3.4. In in the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or or light source module(s), bear the marking of the rated voltage or range of voltageand rated wattage. 3.5. In in the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The the trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and indelible; 3.5.2. The the specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or charactersbelow; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.12. 2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The the marking of the rated voltage or range of voltageand rated wattage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog Cornering lamps submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above.; 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must shall be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.14.3.1.1. below and, in the case several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltage. 3.6. Lamps operating at voltages other than the nominal rated voltages of 6 V, 12 V or 24 V respectively, by the application of an electronic light source control gear being not part of the lamp, shall also bear a marking denoting the rated secondary design voltage. 3.7. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps Devices submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate Comprise a space of sufficient size for the approval ▇▇▇▇ marking and for the additional symbols prescribed in paragraph 4.34.2. below; the said this space shall be shown in the drawings referred to mentioned in paragraph 2.2.1. above.; 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ of the applicant; this marking must shall be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must shall be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.12.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps 3.1. Headlamps or distributed lighting systems submitted for approval shall: 3.1. Bear shall bear legibly and indelibly the trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and be indelible;. 3.2. With They shall comprise, on the exception lens and on the main body3, spaces of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating: (a) The category or categories of light source prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space sufficient size for the approval ▇▇▇▇ and for the additional symbols prescribed referred to in paragraph 4.3. below4.; the said space these spaces shall be shown in indicated on the drawings referred to in paragraph 2.2.1. above. 3.3. Headlamps designed to satisfy the requirements of both right-hand and left- hand traffic shall bear markings indicating the two settings of the optical unit on the vehicle or of the gas-discharge light source on the reflector; these markings shall consist of the letters "R/D" for the position for right-hand traffic and the letters "L/G" for the position for left-hand traffic. 3.4. In the case All beams may bear on their light-emitting surface a centre of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltagereference as shown in Annex 6. 3.5. In the case of a light-generator of a distributed lighting system using a non- replaceable gas-discharge light source not approved under Regulation No. 99, the light-generator shall bear the trade name or ▇▇▇▇ of its manufacturer and the part number referred to in paragraph 2.2.2. above. 3.6. In the case of lamps with light source LED module(s), the lamp shall bear the marking of the rated voltage and rated wattage and the light source module specific identification code. 3.7. LED module(s) shall bearsubmitted along with the approval of lamp: 3.5.13.7.1. The Shall bear the trade name or ▇▇▇▇ of the applicant; this . This marking must shall be clearly legible and indelible; 3.5.23.7.2. The Shall bear the specific identification code of the module; this . This marking must shall be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.12.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.33.8. The marking of the rated voltage or range of voltage. 3.6. An If an electronic light source control gear or a variable intensity control being which is not part of a LED module is used to operate a LED module(s), it shall be marked with its specific identification code(s), the lamp but not included into the lamp body shall bear the name of the manufacturer rated input voltage and its identification numberwattage.

Markings. Rear fog Daytime running lamps submitted for approval shall: 3.14.1. Bear the trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and be indelible; 3.24.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.34.3. In the case of lamps with an electronic light source control gear and/or non- replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage and rated maximum wattage. 4.4. Provide adequate space for the approval ▇▇▇▇ and for the additional symbols prescribed in paragraph 4.35.2. below; the said space shall be shown in the drawings referred to in paragraph 2.2.13.2.1. above. 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.54.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.14.5.1. The trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and indelible; 3.5.24.5.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 45. 3.1.12.1.1. below and, in the case several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.13. 2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.34.5.3. The marking of the rated voltage and rated wattage. 4.6. Lamps operating at voltages other than the nominal rated voltages of 6 V, 12 V or range 24 V respectively, by the application of an electronic light source control gear being not part of the lamp, must also bear a marking denoting the rated secondary design voltage. 3.64.7. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps Devices submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate Comprise a space of sufficient size for the approval ▇▇▇▇ marking and for the additional symbols prescribed in paragraph 4.34.2. below; the said this space shall be shown in the drawings referred to mentioned in paragraph 2.2.1. above.; 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must shall be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.12.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltage. 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog 4.1. Side-marker lamps submitted for approval shallapproval: 3.14.2. Bear Must bear the trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and be indelible;. 3.24.3. With the exception of lamps with non-replaceable light sources must bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.34.4. Provide adequate Must comprise a space of sufficient size for the approval ▇▇▇▇ marking and for the additional symbols prescribed in paragraph 4.35.4. below; the said this space shall be shown in the drawings referred to mentioned in paragraph 2.2.13.2.1. above. 3.44.5. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or or light source module(s), shall bear the marking of the rated voltage or the range of voltagevoltages, and the rated wattage. 3.54.6. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.14.6.1. The trade name or ▇▇▇▇ of the applicant; this marking must be clearly legible and indelible; 3.5.24.6.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 45.4. 3.1.11.1. below and, in the case of several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.13. 2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.34.6.3. The marking of the rated voltage or range of voltage(and rated wattage). 3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog lamps The samples of a type of cornering lamp submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or and/or (b) The b)The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above.; 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-non- replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltagevoltage and rated maximum wattage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must shall be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.14.3.1.1. below and, in the case several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage and rated wattage. 3.6. Lamps operating at voltages other than the nominal rated voltages of 6 V, 12 V or range 24 V respectively, by the application of an electronic light source control gear being not part of the lamp, shall also bear a marking denoting the rated secondary design voltage. 3.63.7. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog Cornering lamps submitted for approval shall: 3.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and be indelible; 3.2. With the exception of lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ mark and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above.; 3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-non- replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.5. In the case of lamps with light source module(s), the light source module(s) shall bear: 3.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must shall be clearly legible and indelible; 3.5.2. The specific identification code of the module; this marking must shall be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.1. below and, in the case several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.3. The marking of the rated voltage or range of voltage. 3.6. Lamps operating at voltages other than the nominal rated voltages of 6 V, 12 V or 24 V respectively, by the application of an electronic light source control gear being not part of the lamp, shall also bear a marking denoting the rated secondary design voltage. 3.7. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.

Markings. Rear fog Daytime running lamps submitted for approval shall: 3.14.1. Bear the trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and be indelible; 3.24.2. With the exception of daytime running lamps with non-replaceable light sources sources, bear a clearly legible and indelible marking indicating: (a) The category or categories of light source source(s) prescribed; and/or (b) The light source module specific identification code. 3.3. Provide adequate space for the approval ▇▇▇▇ and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above. 3.4. In the case of daytime running lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage. 3.54.4. Provide adequate space for the approval mark and for the additional symbols prescribed in paragraph 5.2. below; the said space shall be shown in the drawings referred to in paragraph 3.2.1. above. 4.5. In the case of daytime running lamps with light source module(s), the light source module(s) shall bear: 3.5.14.5.1. The trade name or ▇▇▇▇ mark of the applicant; this marking must be clearly legible and indelible; 3.5.24.5.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4. 3.1.15.2.1.1. below and, in the case several non non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.13. 2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. 3.5.34.5.3. The marking of the rated voltage or range of voltage. 3.64.6. Lamps operating at voltages other than the nominal rated voltages of 6 V, 12 V or 24 V respectively, by the application of an electronic light source control gear being not part of the lamp, must also bear a marking denoting the rated secondary design voltage. 4.7. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.