CFR PART 200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, class, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
LEAVE FOR PROVINCIAL CONTRACT NEGOTIATIONS 1. The employer shall grant a leave of absence without pay to an employee designated by the BCTF for the purpose of preparing for, participating in or conducting negotiations as a member of the provincial bargaining team of the BCTF.
Errors and Omissions, Professional Liability or Malpractice Insurance Contractor may be required to carry errors and omissions, professional liability or malpractice insurance. All policies shall remain in force through the life of this Contract and shall be payable on a "per occurrence" basis unless County specifically consents to a "claims made" basis. The insurer shall supply County adequate proof of insurance and/or a certificate of insurance evidencing coverages and limits prior to commencement of work. Should any of the required insurance policies in this Contract be cancelled or non-renewed, it is the Contractor’s duty to notify the County immediately upon receipt of the notice of cancellation or non-renewal. If Contractor does not carry a required insurance coverage and/or does not meet the required limits, the coverage limits and deductibles shall be set forth on a waiver, Exhibit C, attached hereto. Failure to provide and maintain the insurance required by this Contract will constitute a material breach of this Contract. In addition to any other available remedies, County may suspend payment to the Contractor for any services provided during any time that insurance was not in effect and until such time as the Contractor provides adequate evidence that Contractor has obtained the required coverage.
200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, glass, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
Benefit to Citizens of Xxxxxxx County The safety of the citizens of Xxxxxxx County is enhanced through this Agreement, which promotes safe boating conditions and reduces costs associated with patrols of recreational waterways.
General Policies (a) The evaluated job rate arrived at through official evaluation by the Joint Job Evaluation Board will be final and binding upon both parties to the Labour Agreement unless review has been requested as provided in Section 3(a)(ii)(c) or 3(a)(ii)(g). In case of such review the decision of the Job Evaluation Directors or, where appropriate the Independent Review Officer shall be final and binding upon both parties. Where a number of appeals indicate a problem within a job field, the Directors shall refer such problems to the Administrative Committee for final determination.
What Are the Qualifications for Charitable Donations The Pension Protection Act of 2006 allows Xxxx XXX holders who are RMD age or older at the time of a distribution to annually exclude qualified charitable distribution amounts up to $100,000 per year from gross income. The provision was made permanent by the PATH Act of 2015. A qualified charitable distribution must be made payable directly to the qualified charity as described in Section 170(b) of the Internal Revenue Code. Distributions from SEP or SIMPLE IRAs do not qualify for this type of designation.
Submissions on Behalf of Others Should You wish to submit work that is not Your original creation, You may submit it to OIDF separately from any Contribution, identifying the complete details of its source and of any license or other restriction (including, but not limited to, related patents, trademarks, and license agreements) of which you are personally aware, and conspicuously marking the work as "Submitted on behalf of a third-party: [named here]".
Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
Excess/Umbrella Liability Policies Required insurance coverage limits may be provided through a combination of primary and excess/umbrella liability policies. If coverage limits are provided through excess/umbrella liability policies, then a Schedule of underlying insurance listing policy information for all underlying insurance policies (insurer, policy number, policy term, coverage and limits of insurance), including proof that the excess/umbrella insurance follows form must be provided after renewal and/or upon request.
