Wash all machine-washable bedding, drapes, and clothing, on the hottest water temperature and dry on the highest heat setting. Items that cannot be washed must be taken to a dry cleaner who MUST be informed of the issue. You must safely discard ALL items that cannot be decontaminated.
Fittings 3.2.1 Landing gear support structure and attachment fitting
Retrenchment At any time during an individual’s service, the individual may be subject to retrenchment in accordance with the provisions of Article 22 of the Agreement. In such cases, the notice provisions and all other terms of that article shall apply, anything above to the contrary notwithstanding.
Grooming The parties agree that the agency shall have the right to set reasonable and professional grooming standards for its employees. The agency and state agree to consult with the Association in the development of said grooming standards.
KITCHEN Discard all leftover food in large trash receptacle in kitchen and empty any smaller trash receptacles if used into large trash can in kitchen. Empty large trash bin into the dumpster, (if feasible). If not, please notify front desk. Flatware is to be pre-soaked, washed in dishwasher, dried, returned to drawers and placed facing in the same direction. Dishes, glassware, chopping boards, cooking utensils, pots/pans, baking sheets etc. should be washed in accordance with the instructions on the dish washing machine and returned DRY to dish carts and cupboards. Please check for lipstick/chap stick marks and clean those off accordingly before putting glasses/cups away. Wipe down outside of dishwasher, empty dishwasher food trap into trash and wash out. Counters and sinks wiped down with the water and bleach solution. If used, please wipe inside and out microwave oven; wall/warming ovens, inside the refrigerator and refrigerator door. Run garbage disposal in large double sink by dishwashing machine to clear food waste (Please do not put any food waste in small sinks). Wipe out Alto-Shaam (Warming Ovens) and clean food trays if used. Rinse out any Dish Tubs. Empty any tubs of excess ice outside, if used. Sweep floor of food debris. Empty large trash bin into the dumpster (if feasible). If not please notify front desk. B BQ’s: Make sure propane is turned off after use Clean grill racks with wire brush and wipe up any spills /food debris from the BBQ Leave outside to cool. Please check with Front Desk regarding storage of cold and cleaned BBQ’s PATIO: Return outdoor umbrellas and furniture to original positions. Wipe down outdoor furniture if spills have occurred. Dispose of trash/food waste and cigarette butts in trash receptacles. The following applies if any food and/or beverages have been served in these rooms: GREAT ROOM: Wipe down tables with bleach /water solution. (Located under the sink in the kitchen next to the coffee maker). If linens have been used or rented, please shake off any food debris in trash receptacles and place linens in mesh bags provided. Sorting by color or type is not necessary. Notify front desk of any beverage spills as soon as they occur. Empty any trash receptacles into large trash can in kitchen and then empty that into the dumpster (if feasible). If not please notify front desk. Sweep/Vacuum carpet of any food debris. (These items are located in the cupboard next to Men’s restroom.
Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.
Welding Welding and use of cutting torches or cutoff saws will be permitted only in areas that have been cleared or are free of all material capable of carrying fire. Flammable debris and vegetation must be removed from within a minimum 10-foot radius of all welding and cutting operations. A shovel and a 5-gallon standard backpack water container filled and with handpump attached shall be immediately available for use in the event of a fire start. C8.212 – MARKET-RELATED CONTRACT TERM ADDITION (11/08). The term of this contract may be adjusted when a drastic reduction in wood product prices has occurred in accordance with 36 CFR 223.52. The Producer Price Index used to determine when a drastic reduction in price has occurred is stated in A20. Purchaser will be notified whenever the Chief determines that a drastic reduction in wood product prices has occurred. If the drastic reduction criteria specified in 36 CFR 223.52 are met for 2 consecutive calendar quarters, after contract award date, Contracting Officer will add 1 year to the contract term, upon Purchaser’s written request. For each additional consecutive quarter such a drastic reduction occurs, Contracting Officer will, upon written request, add an additional 3 months to the term during Normal Operating Season, except that no single 3-month addition shall extend the term of the contract by more than one year. Contracting Officer must receive Purchaser’s written request for a market-related contract term addition before the expiration of this contract. No more than 3 years shall be added to a contract's term by market-related contract term addition unless the following conditions are met:
Rubric The rubrics are a scoring tool used for the Educator’s self-assessment, the formative assessment, the formative evaluation and the summative evaluation. The districts may use either the rubrics provided by ESE or comparably rigorous and comprehensive rubrics developed or adopted by the district and reviewed by ESE.
Millwright In the case of a job site located outside a millwright’s region of residence, the employer may assign a millwright holding a journeyman competency certificate or an apprentice competency certificate anywhere in Quebec, provided the millwright has worked 1,500 or more hours for the employer in the construction industry in Quebec or elsewhere in Canada during the first 24 months of the 26 months preceding the issuance or renewal of his competency certificate, as follows:
Shiftwork 38.1 Shift Penalties (Excluding Home Care Classifications)
