For AFS Sample Clauses
The 'For AFS' clause designates specific terms or conditions that apply to transactions or arrangements involving the entity or concept referred to as AFS, which could stand for 'Available For Sale' in financial contexts or another defined term in the agreement. This clause typically outlines how assets, products, or services categorized under AFS are to be treated, such as their accounting treatment, reporting requirements, or eligibility for certain rights or obligations. Its core practical function is to ensure that all parties clearly understand the special provisions or exceptions that apply to AFS, thereby reducing ambiguity and potential disputes regarding their handling.
For AFS the front-lighting function(s) produced (passing-beam, driving-beam and adaptive main-beam); the change of mode(s) and/or class(es) does not constitute a change of type;
For AFS the front-lighting function(s), mode(s) and classes produced;
For AFS. Systems
9.3.1. Category as described by the relevant marking5 .....................................................
For AFS. Systems
9.3.1. Category as described by the relevant marking0
9.3.2. Number, category and kind of light source(s)
9.3.2.1. Number and specific identification code(s) of LED module(s) and for each LED module a statement whether it is replaceable or not: yes/no1
9.3.2.2. Number and specific identification code(s) of electronic light source control gear(s), if applicable
9.3.2.3. Total objective luminous flux as described in paragraph 4.5.2.6. of this Regulation exceeds 2,000 lumen: yes/no1
(a) Indications according to paragraph 5.3.5.1. of this Regulation (which lighting unit(s) provide a "cut-off" as defined in Annex 5 of this Regulation, that projects into a zone extending from 6 degrees left to 4 degrees right and upwards from a horizontal line positioned at 0.8 degree down)
(b) The adjustment of the "cut-off" has been determined at 10 m / 25 m1
(c) The determination of the minimum sharpness of the "cut-off" has been carried out at 10 m / 25 m1
9.3.4. The vehicle(s) for which the system is intended as original equipment
9.3.5. Whether approval is sought for a system which is not intended to be included as part of the approval of a vehicle type according to UN Regulation No. 48: yes/no1
9.3.5.1. If in the affirmative: information sufficient to identify the vehicle(s) for which the system is intended
9.3.6. Indications according to paragraph 5.3.5.2. of this Regulation (which class E passing beam mode(s), if any, comply with a "data set" of Table 14 of this Regulation)
9.3.7. Whether approval is sought for a system intended to be installed on vehicles only, which provide means for a stabilization/limitation of the system's supply: yes/no1
9.3.8. The adjustment of the "cut-off" has been determined at 10 m / 25 m. 1 The determination of the minimum sharpness of the "cut-off" has been carried out at 10 m / 25 m. 1
9.3.9. The system is designed to provide passing beams of:0
9.3.9.1. Class C Class V Class E Class W
9.3.9.2. With the following mode(s), identified by the designation(s), if it applies14 Mode No. C 1 Mode No. V … Mode No. E … Mode No. W … Mode No. C … Mode No. V … Mode No. E … Mode No. W … Mode No. C … Mode No. V … Mode No. E … Mode No. W …
9.3.9.3. Where the lighting units indicated below are energized5,0, 0 for the mode No. .....
(a) If no bend lighting applies: Left side ▇▇.▇ ▇▇.▇ ▇▇.▇ ▇▇.▇ No. 9 ▇▇.▇▇ ▇▇▇▇▇ ▇▇▇▇ ▇▇.▇ ▇▇.▇ ▇▇.▇ ▇▇.▇ ▇▇.▇▇ ▇▇.▇▇
(▇) If bend lighting of category 1 applies: Left side ▇▇.▇ ▇▇.▇ ▇▇....
For AFS. Systems3 9.3.1. Category as described by the relevant marking7 .................................................... DC, DCR, DC/R, DC/, DC PL, DCR PL, DC/R PL, DC/PL, DLSC, DLSC, DLSC/, DLSCR, DLSC/PL, DLSC/R, DLSR, DLSC/, DLSCR, DLSC PL, DLSC/R, DLSCR PL, DLSC PL, DLSC/R PL, DLSR PL, DLSC/PL, DLSCR PL, DLSC/R PL, DLSC, DLSCR, DLSC/R, DLSC/, ▇▇▇▇ ▇▇, ▇▇▇▇▇ ▇▇, ▇▇▇▇/▇ ▇▇, ▇▇▇▇/▇▇, ▇ In the case of a DLS using a non-replaceable gas-discharge light source not approved under Regulation No. 99 shall be indicated the part number assigned by the light-generator manufacturer to the light-generator.