DUCT WORK Sample Clauses

POPULAR SAMPLE Copied 1 times
DUCT WORK. Unless the approved drawings provide otherwise, in buildings with a pressurized ceiling supply system, a ducted supply and return air system shall be installed. The return air duct shall connect to the return air shaft. The duct work shall be no less than 22 gauge metal and maximum allowable length of flex duct from the diffuser to the metal duct shall be 10 feet. In buildings with pressurized ceiling supply systems, drywall shall be installed slab to slab to isolate the duct system from the original paper barrier system. The integrity of the remaining paper barrier system shall be maintained.
View Source
DUCT WORK. Duct will be galvanized steel with thickness appropriate for the duct size. Duct will be either rectangular or spiral reinforced, round cross section. Exterior duct runs will be insulated.
View Source
DUCT WORK. Remove dust and debris from all ductwork. (5). Plumbing and Plumbing Fixtures Free all pipes and fittings from dirt and debris clean and polish all fixtures and ensure that facilities are in proper working order.
View SourceView Similar (2)
DUCT WORK. Foil-faced fiberglass blanket with vapor barrier.
View SourceView Similar (3)
DUCT WORK. 8.1 Foil-faced fiberglass blanket with vapor barrier. 8.1.1 Before wrapping the flexible blanket insulation, cut out and remove two inches of insulation at the butt and lateral ends of the flexible blanket. The two-inch laps will serve as vapor barrier flaps at all joints. All insulation will be wrapped tightly and neatly to all surfaces with all joints butted accurately. A completely sealed vapor barrier envelope must be provided. 8.1.2 Joints of the insulation will be lapped, sealed and taped with the proper sealer to provide a completely sealed vapor barrier envelope. The tape will be applied in a straight line with equal overlap on both sides of the joint. All punctures and voids must be properly insulated and sealed. 8.1.3 If a self-sealing tape is used, it shall be rubbed until it is free of air pockets or openings. 8.1.4 No raw glass shall be visible.
View SourceView Similar (2)
DUCT WORK. COVERED, limited to: Exposed ductwork. EXCLUDED, but not limited to: Inaccessible and/or concrete encased ducts.
View Source
DUCT WORK. The above units will have fiberglass duct work with supply and return grilles.
View Source
DUCT WORK. Remove dust and debris from all ductwork.
View Source
DUCT WORK. All duct work shall conform to a minimum SMACNA standard; existing duct work shall be evaluated and reused whenever possible. All installations shall conform to prevailing code requirement in term of gauge of metal and fire damper. Contractor shall be responsible for resealing and insulating duct work as necessary to meet code.
View Source

Related to DUCT WORK

  • Contract Work Contract work means capital project work within existing plant facilities, major maintenance and/or revamp work, plant modifications and/or shutdown work, minor maintenance and/or repair work, breakdown maintenance.

  • Project Work PURCHASER shall complete the following projects in accordance with the specifications provided in Exhibits B, C, D, E, and F and written instructions from STATE. Project locations are shown on Exhibit A unless otherwise described. PURCHASER shall furnish all material unless otherwise specified.

  • THE WORK The Work comprises the completed construction required by the Contract Documents and includes all labor necessary to produce such construction, and all materials and equipment incorporated or to be incorporated in such construction.

  • Shift Work ‌ (1) Except as varied by this Clause, all other aspects of Section 4 of the Agreement shall apply to the working of shift work. (2) The Company has the right to direct Employees to work shift work as required and the Employees shall work the shift work as directed. Shift work will be worked and paid for in accordance with this subclause. (3) Shift work is deemed to be any arrangement of Project Working Hours where the majority of the Ordinary Hours are worked outside of the spread of Ordinary Hours defined at clause 16 - Hours of Work of this Agreement and when Employees are working as such. (4) Ordinary Hours for shift Employees will comprise thirty-six (36) hours per week averaged over a defined work cycle and will not commence before 5.00pm on Sunday night. Such Ordinary Hours are the specified hours under each shift Employee's terms of employment by reference to which annual leave and personal/carer's leave accrue. (5) Prior to the commencement of shift work, the Company shall seek the agreement of the Employees involved. Failing agreement, the Company will provide to the Employees concerned one (1) week's notice of the commencement of shift work and the starting and finishing times of Ordinary Hours of the shifts. (6) Where less than five (5) consecutive shifts are worked then Employees shall be paid at overtime rates in lieu of the shift loading prescribed at subclause (7) of this clause. The consecutive nature of shifts will not be deemed to be broken if work is not carried out on a Saturday, Sunday, RDO or on any public holiday. (7) A shift Employee shall receive a flat loading of twenty-five (25) percent of their Ordinary Hourly Rate for each hour worked. (8) Employees working night shift shall be entitled to stop work for a half-hour without deduction of pay for the purpose of taking a meal break. (9) The Company may stagger the times for Employees to take meal breaks to meet operational requirements. (10) The Company shall structure the Project Working Hours for Employees working night shift to include one (1) half-hour rest break to be taken without deduction of pay by Employees working the Project Working Hours on any night shift.

  • Unsafe Work An employee may exercise their right to refuse to do unsafe work pursuant to Section 3.12 of the Occupational Health and Safety Regulations outlined in Information Appendix B. An employee must not be subject to discriminatory or disciplinary action pursuant to Section 3.13(1) of the Occupational Health and Safety Regulations outlined in Information Appendix B.