DRAWINGS TO BE SUPPLIED BY THE CONTRACTOR. 4.7.1 Where drawings/ data are to be furnished by the Contractor, they shall be as enumerated in the Special Conditions of Contract, and shall be furnished within the specified time.
DRAWINGS TO BE SUPPLIED BY THE CONTRACTOR Sample Clauses
Related to DRAWINGS TO BE SUPPLIED BY THE CONTRACTOR
Release by the Contractor The acceptance by the Contractor of final payment shall release NYSERDA from all claims and liability that the Contractor, its representatives and assigns might otherwise have relating to this Agreement.
TERMINATION BY THE CONTRACTOR If the Work is stopped for a period of thirty days under an order of any court or other public authority having jurisdiction, or as a result of an act of government, such as a declaration of a national emergency making materials unavailable, through no act or fault of the Contractor or a Subcontractor or their agents or employees or any other persons performing any of the Work under a contract with the Contractor, or if the Work should be stopped for a period of thirty days by the Contractor because the Architect has not issued a Certificate for Payment as provided in Paragraph 9.7 of these General Conditions or because the State has not made payment thereon as provided in Paragraph 9.7, then the Contractor may, upon seven additional days written notice to the State and the Architect, terminate the Contract and recover from the State payment for all Work executed and for any proven loss sustained upon any materials, equipment, tools, construction equipment and machinery, including reasonable profit and damages.
Acceptance by the City It is expressly understood and agreed that all materials provided and/or work done by the Contractor shall be subject to inspection and acceptance by the City at its discretion, and that any progress inspections and approval by the City of any item or work shall not forfeit the right of the City to require the correction of faulty workmanship or material at any time during the course of the work, although previously approved by oversight. Nothing herein contained shall relieve the Contractor of the responsibility for proper construction and maintenance of the work, materials and equipment required under the terms of this Contract until all work has been completed and accepted by the City.
INFORMATION AND SERVICES TO BE FURNISHED BY THE LPA The information and services to be furnished by the LPA are set out in Appendix "B” which is herein attached to and made an integral part of this Contract.
SUB-CONTRACTOR Section 1. The Employer shall not contract any work covered by this Agreement to be done at the site of construction, alterations, repairs or any new construction to any person, firm or company that does not have an existing labor agreement with the Union covering such work within the scope of this Agreement.
Maintenance by the Manager Throughout the Term the Manager will inspect, maintain, repair and replace elements of the Residence in order to keep the Residence in a good condition and state of repair, complying with health, safety and fire standards required by law. This includes, but is not limited to, inspecting and testing fire safety equipment, major appliances, electrical, bathroom fixtures and plumbing.
Payment for Forest Products Delivered Purchaser agrees to pay the State for delivered forest products at the following rate: $0.00/MBF $250.00/MBF for incorrect species delivery* $20/mbf for Utility logs (Adjusted Gross). Purchaser agrees to increase the above delivered payment rate as approved by the State in the event the location of delivery is changed per the G-026.2 clause. Purchaser will not be billed for any delivered logs that are scaled as containing metal. *When two or more log sorts from this project are delivered to the same destination, the species contained in them are not eligible for the species price reduction. P-036.2 Missorts and Payment Reduction for Delivered Forest Products Forest Products delivered that do not meet the sorting specifications in G-022.2 are considered mis-sorts. Purchaser receiving mis-sort Forest Products is required to pay the State at the bid price under this contract. However, when mis-sorted Forest Products amount to more than 5% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-sort threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-sort payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-sort price reduction are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-sorted will be calculated as follows: Payment Reduction = (B x M) x R Where: B = Bid rate from P-028.2 clause M = Mis-sorted volume exceeding threshold excluding utility R = Reduction factor* 0.2 for diameter mis-sort 0.3 for high quality mis-sort *Logs eligible for payment reduction based on multiple reduction factors will be calculated at the higher payment reduction factor. Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-sort payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-sorts shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code P-037.2 Mismanufacture and Payment Reduction for Delivered Forest Products Forest Products delivered that do not meet preferred log length specifications or multiples or combinations of preferred lengths and Forest Products delivered not meeting manufacturing standards as described in clause G-024.2 are considered mis- manufactured. Purchaser receiving mis-manufactured Forest Products is required to pay the State at the bid price under this contract. However, when mis-manufactured Forest Products amount to more than 8% of the total delivered sort volume, Purchaser may request approval for payment reduction for delivered volume exceeding the mis-manufacture threshold. Requests for payment reduction must be submitted to the State in writing prior to contract expiration. Eligibility for mis-manufacture payment reduction is subject to State approval and shall be determined by the State’s delivered product analysis. Forest Products determined by the State eligible for mis-manufacture price reductions are not eligible for any other price adjustments. Payment reduction for Forest Products deemed mis-manufactured will be calculated as follows: Payment Reduction = (B x M) x (0.2) Where: B = Bid rate from P-028.2 clause M = Mis-manufactured volume exceeding threshold excluding utility Third-party scaling organization information is required to determine Xxxxxxxx mbf for payment reduction purposes. Value will be derived from the applicable sort value as described in this contract. Scale information for determining mis-manufacture payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for mis-manufacture shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
Where a Contracting Party expropriates the assets of a company which is incorporated or constituted under the law in force in any part of its own territory, and in which investors of the other Contracting Party own shares, it shall ensure that the provisions of this Article are applied so as to guarantee prompt, adequate and effective compensation in respect of their investment to such investors of the other Contracting Party who are owners of those shares.
Termination by the Customer The Customer may terminate this Agreement by providing a written notice of termination to the Transfer Agent, specifying the date as of which this Agreement will terminate, which may be any date, including the date such written notice is provided, provided the circumstances described below giving rise to the termination right are continuing at the time of the Transfer Agent’s receipt of such written notice, if as a result of an Event Beyond Reasonable Control:
CALCULATIONS TO BE MADE BY THIRD PARTY All calculations under this Agreement shall be made annually by an independent third party (the “Third Party”) selected and appointed each year by the District, subject to approval by Applicant in writing, which approval shall not unreasonably be withheld.
