Emission standard means specified limitations on the discharge of air contaminants into the atmosphere.
Uniform standard means a standard adopted by the Commission for a Product line, pursuant to Article VII of this Compact, and shall include all of the Product requirements in aggregate; provided, that each Uniform Standard shall be construed, whether express or implied, to prohibit the use of any inconsistent, misleading or ambiguous provisions in a Product and the form of the Product made available to the public shall not be unfair, inequitable or against public policy as determined by the Commission.
Network Connection Standards means the Distributor’s written technical and safety standards for connection of an Electrical Installation to the Network that are issued by the Distributor and updated from time to time, and include:
Common stack means a single flue through which emissions from two or more units are exhausted.
Destination state means the state, territory, or foreign country to which motor fuel is directed for
Community-Wide Standard means the standard of conduct, maintenance, or other activity generally prevailing in the Community. Such standard may be more specifically determined by the Board of Directors of the Association. Such determination, however, must be consistent with the Community-Wide Standard originally established by the Declarant.
Generally applicable environmental radiation standards means standards issued by the U.S. Environmental Protection Agency (EPA) under the authority of the Atomic Energy Act of 1954, as amended, that impose limits on radiation exposures or levels, or concentrations or quantities of radioactive material, in the general environment outside the boundaries of locations under the control of persons possessing or using radioactive material.
Construction Start Date means the later to occur of the date on which Seller delivers to Buyer (a) a copy of the Notice to Proceed that Seller has delivered to the EPC Contractor for the Project, and (b) a written Certification substantially in the form attached hereto as Appendix IV-1.
European standard means a standard adopted by the European Committee for Standardisation, the European Committee for Electrotechnical Standardisation or the European Telecommunications Standards Institute and made available for public use;
Australian Standard means a standard published by Standards Australia.
2%/25% Guidelines has the meaning set forth in Section 13.
Benchmark Transition Start Date means, in the case of a Benchmark Transition Event, the earlier of (a) the applicable Benchmark Replacement Date and (b) if such Benchmark Transition Event is a public statement or publication of information of a prospective event, the 90th day prior to the expected date of such event as of such public statement or publication of information (or if the expected date of such prospective event is fewer than 90 days after such statement or publication, the date of such statement or publication).
Community practice protocol means a written, executed agreement entered into voluntarily between an authorized pharmacist and a physician establishing drug therapy management for one or more of the pharmacist’s and physician’s patients residing in a community setting. A community practice protocol shall comply with the requirements of subrule 8.34(2).
Good Industry Practice means standards, practices, methods and procedures conforming to the Law and the degree of skill and care, diligence, prudence and foresight which would reasonably and ordinarily be expected from a skilled and experienced person or body engaged in a similar type of undertaking under the same or similar circumstances.
Disturbance Control Standard or “DCS” shall mean the reliability standard that sets the time limit following a disturbance within which a balancing authority must return its Area Control Error to within a specified range.
Design Standards means the standards developed as a requirement of the Programmatic Agreement
Fitch Guidelines means the guidelines, as may be amended from time to time, in connection with Fitch’s ratings of the VMTP Shares.
safety standard means the Code of Practice for the Wiring of Premises SANS 10142-1 incorporated in the Regulations;
Cosmetic means surgery, procedures or treatment and other services performed primarily to enhance or improve appearance, including but not limited to, and except as otherwise required by state or federal law, those surgeries, procedures, treatments and other services performed in the absence of a functional impairment of a body part or organ as documented in the medical record, even if such services will improve emotional, psychological or mental condition or function.
Good Industry Practices means the practices that would be adopted by, and the exercise of that degree of care, skill, diligence, prudence and foresight that reasonably would be expected from, a competent contractor in the international oil and gas industry experienced in performing work similar in nature, size, scope and complexity to the Work and under conditions comparable to those applicable to the Work, where such work is subject to, and such contractor is seeking to comply with, the standards and codes specified in the Contract or (to the extent that they are not so specified) such national or international standards and codes as are most applicable in the circumstances, and the applicable Law.
Effluent limitation guideline means a regulation published by the Administration under Section 304(b) of the CWA to adopt or revise effluent limitations.
Guide dog means: A guide dog as defined in section 1 of the Blind Persons Rights’ Act.
Prudent Industry Practices means, at a particular time, any of the practices, methods, standards of care, skill, safety and diligence, as the same may change from time to time, but applied in light of the facts known at the time, that are consistent with the general standards applied or utilized under comparable circumstances by a reasonably prudent operator, in a good and workmanlike manner, with due diligence and dispatch, in accordance with good midstream industry practice.
Prudent Industry Practice means such practices, methods, acts, techniques, and standards as are in effect at the time in question that are consistent with (a) the standards generally followed by the United States pipeline and terminalling industries or (b) such higher standards as may be applied or followed by the HFC Entities in the performance of similar tasks or projects, or by the HEP Entities in the performance of similar tasks or projects.
New drug means: (i) any drug, except a new animal drug or an animal feed bearing or containing
Contract Standard means such standard as complies in each and every respect with all relevant provisions of the Contract;