Type 2 Installation definition

Type 2 Installation means any Technical Installation upon which all SW deployed is licensed for Use with, but is not running on, such TPD; and,
Type 2 Installation means any Technical Installation upon which all SW deployed is licensed for Use with, but is not running on, such TPD; and,「類型 2 安裝」係指技術安裝,在其上部署的 SW 獲授權隨同該 TPD 使用,但不在該 TPD 上執行;以及
Type 2 Installation means any Technical Installation upon which all SW deployed is licensed for Use with, but is not running on, such TPD; and,ii. 「インストレーションタイプ 2」とは、導入されるすべての SW が当該 TPD と併せた「使用」のために使用権許諾されるが、当該 TPD上で実行されるのではない「テクニカルインストレーション」をいう。

Examples of Type 2 Installation in a sentence

  • Between Type 1 Installation and Type 2 Installation: Bi-directional communication (including data transfers) shall be permitted between SW or TPD in Type 1 Installations and SW in Type 2 Installations.

  • Between Type 1 Installation and Type 2 Installation: Bi- directional communication (including data transfers) shall be permitted between SW or TPD in Type 1 Installations and SW in Type 2 Installations.

  • Between Type 2 Installation and Type 3 Installation: c) Між Установкою 2-го типу та Установкою 3-го типу.

  • Type 2 Installation Line Main Breaker2-Pole, 20 A circuit breaker shown A=Black (Line) B=Black (Line)C=Neutral/Grounded (White)1.

  • Between Type 1 Installation and Type 2 Installation: Bi-directional communication (including data transfers) shall be permitted between SW or TPD in Type 1 Installations and SW in Type 2 Installations./ Antara Instalasi Jenis 1 dan Instalasi Jenis 2: Komunikasi dua arah (termasuk transfer data) akan diperbolehkan antara SW atau TPD dalam Instalasi Jenis 1 dan SW dalam Instalasi Jenis 2.

  • Figure 1.8 Type 2 Installation —Shielded Cable with Brake Conductors Drain Wire for Brake ConductorShield Shield for W GBrake R BConductors Type 3 InstallationThese cables have 3 XLPE insulated copper conductors, 25% minimal overlap with helical copper tape and three (3) bare copper grounds in PVC jacket.TIP: Other types of shielded cable are available, but the selection of these types may limit the allowable cable length.

  • If a sewer pipe is being installed, make a hydrostatic pressure-leakage test in accordance with Section 02958 – Leakage Testing of Sewers, Volume 3 Drainage.5.6 If the casing is in tunnel, install backfill grout to fill the entire tunnel cross-section.5.7 Beyond the ends of the casing, install the sewer in a Type 2 Installation or a higher class if specially designated.

  • Type 2 Installation Main Breaker2-Pole, 20 A circuit breaker shown A=Black (Line) B=Black (Line) C=Neutral (White) Type 2 installation:A typical installation of a type 2 SPD will be connected to the load side of the service panel and is intended to be installed with overcurrent protection to the SPD.1. Determining location:• Ensure conductor lengths are as short and straight as possible for best performance.

  • Upgrade Type 2: Installation of secondary containment for existing tanks.

  • The EAA requests costs and estimated lead/construction time for the following facility Upgrade Types, with consideration given to the requirements discussed in Section 3.2.1 of this proposal document: Upgrade Type 1: Installation of smaller tanks.Upgrade Type 2: Installation of secondary containment for existing tanks.


More Definitions of Type 2 Installation

Type 2 Installation means any Technical Installation upon which all SW deployed is licensed for Use with, but is not running on, such TPD; and,„Inštalácia 2. typu“ znamená ľubovoľnú Technickú inštaláciu, v ktorej je všetok nasadený SW licencovaný na Použitie s takouto TPD, ale nie je spustený na takejto TPD; a
Type 2 Installation means any Technical Installation upon which all SW deployed is licensed for Use with, but is not running on, such TPD; and, “Tip instalacije 2” znači svaka Tehnička instalacija nakon koje je sav uvedeni softver licenciran za Upotrebu s takvim TPD-om, ali se ne izvodi na njemu; i

Related to Type 2 Installation

  • Type 3 Installation means any Technical Installation upon which none of the SW, or only a portion of the SW, deployed is licensed for Use with such TPD, and therefore a TPD is not deployed or running.

  • Type 1 Installation means any Technical Installation upon which all SW deployed is licensed for Use with, and is running on, such TPD;

  • Standard Installation means those installations to Subscribers that are located up to one hundred twenty-five (125) feet from the existing distribution system (Cable System).

  • Existing installation means an installation, construction of which began prior to the effective date of any regulation having application to it.

  • Installation means a stationary technical unit where one or more activities listed in Annex I are carried out and any other directly associated activities which have a technical connection with the activities carried out on that site and which could have an effect on emissions and pollution;

  • Military installation means: a base, camp, post, station, yard, center, homeport facility for any ship, or other activity under the jurisdiction of the Department of Defense, including any leased facility, which is located within any of the several States, the District of Columbia, the Commonwealth of Puerto Rico, the U.S. Virgin Islands, Guam, American Samoa, the Northern Marianas Islands and any other U.S. territory. Such term does not include any facility used primarily for civil works, rivers and harbors projects, or flood control projects.

  • Installation Services means all those services ancillary to the supply of the Plant and Equipment for the Facilities, to be provided by the Contractor under the Contract; e.g., transportation and provision of marine or other similar insurance, inspection, expediting, site preparation works (including the provision and use of Contractor’s Equipment and the supply of all construction materials required), installation, testing, pre-commissioning, commissioning, operations, maintenance, the provision of operations and maintenance manuals, training, etc.