Single coat definition

Single coat means one film coating applied to a metal surface.
Single coat means a single film of coating applied directly to the substrate omitting the primer application.
Single coat means only one film of coating is applied to the metal substrate.

Examples of Single coat in a sentence

  • Single coat red-oxide paint will be applied first after due surface cleaning of rust.

  • Single coat applicationThe recommended method of application is by heavy-duty airless spray equipment.

  • Single coat application The recommended method of application is by heavy-duty airless spray machines.

  • Single coat cement plastersurface finish, coated with plaster primer and two coats of external quality paint finish.

  • Single coat cement plaster as surface finish, coated with plaster primer and two coats ofinternal quality paint finish to match wall colour.

  • Single coat uniformly spread in entire area over a coat of approved PU prime /epoxy primer in two coats at specific locations where geotextile reinforcement is placed.

  • Coverage Rates: Single coat coverage rate for LithiumCure 2000 is 400-450 square feet per gallon for smooth-troweled concrete.

  • Type: Single Coat Chip Seal Width of Traveled Surface: 22’ Thickness: ¼” Single coat chip seal Medway Earlton Road, 1.5 miles (Paid by CHIPS) .

  • BID ITEM #3: STABILIZED SHOULDERS: Single coat surface treatment of shoulders to an average width of four (4) feet.

  • Single coat surfacedressing (first coat)128.009.000.12 to 0.1452.Second coat surfacedressing107.008.000.06 to 0.10However, the actual quantity of binder used in surface dressing shall be designed on the basis of inspection and site conditions, and the extra quantity of binder above as specified in Table: 500-2 2 shall be paid separately as per BOQ item.


More Definitions of Single coat

Single coat means a single film of coating applied directly to the material being coated omitting the prime coat application.
Single coat means a single film coating applied directly to the metal substrate omitting the prime coat.
Single coat means only one film of coating applied on the metal substrate.
Single coat means a single film of coating applied directly to the metal substrate omitting the
Single coat means a single film of coating applied directly to the metal substrate omitting the primer application. (b) This Regulation applies to application area(s), flashoff area(s), and oven(s) of large appliance coating lines involved in prime, single, or topcoat coating operations.‌ (c) This Regulation does not apply to the use of quick-drying lacquers for repair of scratches and nicks which occur during assembly, if the volume of coating does not exceed one quart in any eight-hour period.‌ (d) Emissions of volatile organic compounds from any large appliance coating line subject to this Regulation shall not exceed 4.5 pounds of volatile organic compounds per gallon of solids‌delivered to the coating applicator from prime, single, or topcoat coating operations.
Single coat means a single film of coating applied directly and Physical Agents - Biological Exposure Indices (199[6]7), pages to the metal substrate omitting the primer application. [13 - 38]15 - 40."

Related to Single coat

  • Single use means products or items that are intended for one-time, one-person use and are disposed of after use on each client, including cotton swabs or balls, tissues or paper products, paper or plastic cups, gauze and sanitary coverings, razors, piercing needles, scalpel blades, stencils, ink cups, and protective gloves.

  • Flow coating means a coating labeled and formulated exclusively for use by electric power companies or their subcontractors to maintain the protective coating systems present on utility transformer units.

  • Single Phase Aerosol Air Freshener means an aerosol air freshener with the liquid contents in a single homogeneous phase and which does not require that the product container be shaken before use.

  • Floor coating means an opaque coating that is labeled and designed for application to flooring, including but not limited to, decks, porches, steps, and other horizontal surfaces which may be subject to foot traffic.

  • Single tomogram system means a CT x-ray system which obtains x-ray transmission data during a scan to produce a single tomogram.

  • Air dried coating means a coating that is dried by the use of air or forced warm air at temperatures up to 1940F (900C).

  • Flat coating means a coating that is not defined under any other definition in this section and that registers gloss less than 15 on an 85-degree meter or less than 5 on a 60-degree meter.

  • Touch-up coating means a coating used to cover minor coating imperfections appearing after the main coating operation.

  • Dip coating means the application of a coating material to a substrate by dipping the part into a tank of the coating material.

  • Basecoat means a coat of colored material, usually opaque, that is applied before graining inks, glazing coats, or other opaque finishing materials and is usually topcoated for protection.

  • Suction outlet means the opening or fitting through which the water under negative pressure is drawn from the pool or spa.

  • stacked townhouse means a building, other than a townhouse or apartment building, containing at least 3 dwelling units, each dwelling unit being separated from the other vertically and/or horizontally, and each dwelling unit having an entrance to grade shared with no more than 3 other units;

  • Geothermal fluid means water in any form at temperatures greater than 120

  • Industrial maintenance coating means a high performance architectural coating, including primers, sealers, undercoaters, intermediate coats, and topcoats formulated for application to substrates, including floors, exposed to one or more of the following extreme environmental conditions listed below and labeled “For industrial use only;” “For professional use only;” “Not for residential use;” or “Not intended for residential use.”

  • Hair mousse means a hairstyling foam designed to facilitate styling of a coiffure and provide limited holding power.

  • Shopping cart means those push carts of the type or types which are commonly provided by grocery stores, drug stores or other retail mercantile establishments for the use of the public in transporting commodities in stores and markets and, incidentally, from the stores to a place outside the store.

  • Antenna coating means a coating labeled and formulated exclusively for application to equipment and associated structural appurtenances that are used to receive or transmit electromagnetic signals.

  • Single Source means an individual, partnership, corporation, association, labor organization, or any other organization or group of persons which is not a political committee or political party.

  • Prime coat means the first of two or more films of coating applied to a metal surface.

  • Specialty coating means any coating that is manufactured and used for one (1) of the following specialized applications:

  • Roll coating means the application of a coating material to a substrate by means of hard rubber or steel rolls.

  • Single Audit means an audit that includes an examination of an organization's financial statements, internal controls, and compliance with the requirements of Federal or State awards.

  • Furniture coating means any paint designed for application to room furnishings including, but not limited to, cabinets (kitchen, bath and vanity), tables, chairs, beds, and sofas.

  • Check Meter means the Buyer revenue-quality meter section(s) or meter(s), which Buyer may require at its discretion, and which will include those devices normally supplied by Buyer or Seller under the applicable utility electric service requirements.

  • Repair coating means a coating used to re-coat portions of a previously coated product which has sustained mechanical damage to the coating following normal coating operations.