Shafts. definition

Shafts. means a maximum of four combination ventilation and escape shafts to be constructed on the Licensed Areas giving access to the Decline.
View Source
Shafts.. The term "sha s" means any vertical opening through the strata which is or may be used for the pur pose of ventilation or escapement, or for hoisting or lowering of men or in connection with the of coal.
View Source
Shafts. means the entire diaphysial portion of a femur, humerus, or tibia which meets or exceeds the specifications set forth on the "Cortical Bone Specifications and Reimbursement Schedule" and "Recovery Protocols," and "Donor Selection Criteria" attached hereto.
View Source

Examples of Shafts. in a sentence

  • Drive Axle: Axle Housings and Internal Parts; Axle Shafts; Drive and Output Shafts; and Universal Joints; but excluding the Secondary Drive Axle on vehicles other than passenger vans, mounted on a truck chassis.

  • Four-Wheel Drive (4x4): Transfer Case and all Internal Parts; transfer case control module and shift mode motor assembly Axle Housing and all Internal Parts; Axles Shafts; Axle Shaft Bearings; Drive Shafts Assemblies (Front and Rear); Drive Shaft Center Bearings; Universal Joints and Yokes; Disconnect Housing Assembly; Seals and Gaskets for the listed components only.

  • Rear Wheel Drive: Rear Axle Housing and all Internal Parts; Axle Shafts; Axle Shaft Bearings; Drive Shaft Assemblies; Drive Shaft Center Bearings; Universal Joints and Yokes; Seals and Gaskets for listed components only.

  • Drilled Shafts are listed in the recommendations for use at the ▇▇▇▇▇.

  • Shafts 0 0 47 111 177 208 0 0 543 Total 462 530 621 685 751 782 355 0 4,186 FLOOR RENTABLE AREA 9,774 345 30,966 30,902 30,070 26,273 2,541 676 131,547 USEABLE AREAS Office Areas 337 171 29,805 29,741 28,909 24,405 0 676 114,044 Store Areas 2,179 0 0 0 0 0 0 2,179 Building Common Areas 7,258 174 0 0 0 2,541 9,973 Total 9,774 345 29,805 29,741 28,909 24,405 2,541 676 126,196 Floor Common Areas Elevator Lobby/Corridor 0 0 434 434 434 1170 0 0 2,472 Tel/Elec.

  • Drive Axle: Axle Housings and Internal Parts; Axle Shafts; Drive and Output Shafts; and Universal Joints; but excluding the Secondary Drive Axle on Vehicles other than passenger vans, mounted on a truck chassis.

  • Shafts shall be of a size commensurate with safe working practices.

  • FRONT & REAR SUSPENSION: Upper and Lower Control Arms; Control Arm Shafts and Bearings or Bushings; Upper and Lower Ball Joints; Radius Arm and Bushings; Torsion Bars, Mounts and Bushings; Stabilizer Bar, Links and Bushings; Struts; Strut Bearing Plates; Spindle and Spindle Support; Wheel Bearings; Pannard Bar; Track Bar; Suspension Bumpers; Leaf Springs; Leaf Spring Shackles and Hardware; Load Assist Shocks; Shocks; Load Assist Springs; and Coil Springs.

  • This means that sub-contractors will not be performing Hull Steelwork, Pulling Shafts, Removing Rudders, Installing Ballast Piping or ▇▇▇▇▇▇ Bulkheads when there are laid-off Employees in that department.

  • Upper and Lower Control Arm Shafts; Bearings and Bushings; Wheel Bearings; Spindles; Ball Joints; King Pins and Bushings; Radius Arm and Bushings; Stabilizer Bar, Links, and Bushings; Wheel Bearings; Torsion Bars; Hub Assembly; Coil Springs; Leaf Springs; and Suspension Level Control Compressor.