RUPD definition

RUPD normally consists of a cross‑member and links to the chassis side members or other structural members of the vehicle;
View Source

Examples of RUPD in a sentence

  • The Union shall give REHS and RUPD as much advance notice as possible, but in no event less than 24 hours’ notice, that an expert will be conducting a health and safety inspection on University premises.

  • Bicycles will be removed from College bike racks if they are not licensed with RUPD during the Winter break and immediately after move-out in May or if deemed abandoned any time.

  • This requirement applies over the entire width of the motor vehicle or trailer and shall be such that the height above the ground of the points of application of the test forces applied to the device according to Part I of this Regulation and recorded in the type approval communication form (Annex 1, item 7) does not exceed the values in subparagraphs (a) and (b) above, increased by half the minimum section height required for the cross member of the RUPD.

  • By May 15, 2025, the University will provide documentation to OCR regarding the provision of training materials and/or protocols provided to RUPD personnel.

  • Before the application of the test forces the maximum allowed horizontal distance of a single, a segmented or an inclined cross-member of a RUPD is 100 mm between the rear of the cross-member measured at the most forward point and the rear of the cross-member measured at the most rearward point, measured in the longitudinal plane of the vehicle.

  • The Union shall give REHS and RUPD as much advance notice as possible, but in no event less than 24 hours' notice, that an expert will be conducting a health and safety inspection on University premises.

  • However, in case of vehicles of categories O1 and O2 where the tyres project for more than half of their width outside the bodywork (excluding the wheel guards) or outside the chassis in the absence of bodywork, the width of the RUPD shall not be less than 100 mm deducted from the distance measured between the innermost points of the tyres, excluding the bulging of the tyres close to the ground, on either side.

  • This requirement applies over the entire width of the motor vehicle or trailer and shall be such that the height above the ground of the points of application of the test forces applied to the device according to Part I of this Regulation and recorded in the type approval communication form (Annex 1, item 7) does not exceed the values in the paragraphs (a) and (b) above, increased by half the minimum section height required for the cross member of the RUPD.

  • Before the application of the test forces, the maximum allowed horizontal distance of a single, a segmented or an inclined cross-member of a RUPD is 100 mm between the rear of the cross-member measured at the most forward point and the rear of the cross-member measured at the most rearward point, measured in the longitudinal plane of the vehicle.

  • In accordance with Action Item 6, the University will provide the dates on which the revised training materials and/or protocols are provided to RUPD personnel.

Related to RUPD

  • SORA means, in respect of any Singapore Business Day “i”, a reference rate equal to the daily Singapore Overnight Rate Average published by the Monetary Authority of Singapore (or a successor administrator), as the administrator of the benchmark, on the Monetary Authority of Singapore’s website currently at http://www.mas.gov.sg, or any successor website officially designated by the Monetary Authority of Singapore (or as published by its authorised distributors) (the “Relevant Screen Page”) on the Singapore Business Day immediately following such Singapore Business Day “i”; and

  • Becquerel (Bq) means the SI unit of activity. One becquerel is equal to 1 disintegration or transformation per second (dps or tps).

  • snippet means a legally binding agreement (made pursuant to the provisions of this Framework Agreement) for the provision of the Services made between a Contracting Body and the Supplier comprising of an Order Form and the Call-Off Terms;","size":74,"snippetLinks":[{"key":"legally-binding-agreement","type":"clause","offset":[8,33]},{"key":"the-provisions-of-this","type":"clause","offset":[52,74]},{"key":"framework- agreement","type":"definition","offset":[75,94]},{"key":"the-provision-of-the-services","type":"clause","offset":[100,129]},{"key":"contracting-body","type":"definition","offset":[145,161]},{"key":"the-supplier","type":"clause","offset":[166,178]},{"key":"order-form","type":"clause","offset":[196,206]},{"key":"off-terms","type":"clause","offset":

  • SAMR means the State Administration for Market Regulation of the PRC or, with respect to the issuance of any business license or filing or registration to be effected by or with the State Administration for Market Regulation, any Governmental Authority which is similarly competent to issue such business license or accept such filing or registration under the Laws of the PRC.

  • Panchayat means an institution (by whatever name called) of self-government constituted under article 243B, for the rural areas;