Round Trip Time definition

Round Trip Time means the time taken for a packet to travel from a source point to a destination point and back to the source point.
View Source
Round Trip Time or “RTT” refers to the time measured from the sending of the first bit of the first packet of the sequence of packets needed to make a request until the reception of the last bit of the last packet of the sequence needed to receive the response. If the client does not receive the whole sequence of packets needed to consider the response as received, the request will be considered unanswered.
View Source

Examples of Round Trip Time in a sentence

  • Measurement of the latency is basically based on the RTT (Round Trip Time).

  • Network Latency refers to the amount of time (Round Trip Time) that it takes for an IP packet to traverse Northland’s network backbone.

  • The contractor Round Trip Time (RTT) reports the total time in milliseconds (ms) time to send a small data packet and obtain a reply back; must be the faster than 600ms for the Round Trip Time (RTT) for internet service.

  • Round Trip Time is the time taken for an ICMP Ping packet to travel from a source point (On BigAir Network) to a destination point and back to the source point.

  • The Round Trip Time (RTT) is the time it takes for a data packet to reliably travel across the network to the destination and for the sender to receive an acknowledgement that the packet arrived at the destination.

  • Both applications provide support for traffic metrics like Round Trip Time (RTT), jitter, link utilisation, packet counters (in, out, error, drops).

  • Total packet latency is the sum of all of the path latencies and of all the switch latencies encountered along the route (usually reported as RTT, Round Trip Time).

  • In Chapter 8, we highlight the SLA TCP-related issues including the effect of tight policing, the effect of the Committed Burst Size (CBS), the effect of the Round Trip Time, etc., and analyze the SLA QoS behavior under TCP-traffic.

  • Round Trip Time (“RTT”) is the time taken for an ICMP Ping packet to travel from a source point (on our network) to a destination point and back to the source point.

  • Round Trip Time Service Type Network Traffic Flow (%) Time (msec) BigAir Network Traffic Layer 2 and Layer 3 99% 35msec National Traffic Layer 2 and Layer 3 98% 55msec Internet Traffic – Australia Layer 3 only 95% 55msec Internet Traffic – USA Layer 3 only 95% 220msec Internet Traffic - UK Layer 3 only 90% 300msec Note: All Internet Services are a best effort service and hence Round Trip Time measures are an indicative performance Target with no associated rebates.

Related to Round Trip Time

  • Central Clock Time or "CCT" means Central Daylight Time when Daylight Savings Time is in effect and Central Standard Time when Daylight Savings Time is not in effect.

  • Down Time means the time period when specified services with specified technical and service standards are not available to user(s).

  • Rebalance Business Day means any day which is a, Exchange Business Day and also a day on which commercial banks and foreign exchange markets settle payment in the country in which the relevant Reference Asset is admitted to trading or any other day designated as a Rebalance Business Day by the Issuer.

  • Fully Diluted Weighted Average Basis means, when calculating the number of Outstanding Units for any period, a basis that includes (a) the weighted average number of Outstanding Units during such period plus (b) all Partnership Interests and Derivative Partnership Interests (i) that are convertible into or exercisable or exchangeable for Units or for which Units are issuable, in each case that are senior to or pari passu with the Subordinated Units, (ii) whose conversion, exercise or exchange price, if any, is less than the Current Market Price on the date of such calculation, (iii) that may be converted into or exercised or exchanged for such Units prior to or during the Quarter immediately following the end of the period for which the calculation is being made without the satisfaction of any contingency beyond the control of the holder other than the payment of consideration and the compliance with administrative mechanics applicable to such conversion, exercise or exchange and (iv) that were not converted into or exercised or exchanged for such Units during the period for which the calculation is being made; provided, however, that for purposes of determining the number of Outstanding Units on a Fully Diluted Weighted Average Basis when calculating whether the Subordination Period has ended or Subordinated Units are entitled to convert into Common Units pursuant to Section 5.7, such Partnership Interests and Derivative Partnership Interests shall be deemed to have been Outstanding Units only for the four Quarters that comprise the last four Quarters of the measurement period; provided, further, that if consideration will be paid to any Group Member in connection with such conversion, exercise or exchange, the number of Units to be included in such calculation shall be that number equal to the difference between (x) the number of Units issuable upon such conversion, exercise or exchange and (y) the number of Units that such consideration would purchase at the Current Market Price.

  • Bill Date The date when a CenturyLink service is billed and/or invoiced to a customer. The Bill Date is generally the date one (1) Day past the billing cycle close date and will appear on any such bill or invoice.