Minimum Peak Power definition
Minimum Peak Power is defined as the minimum rated power, as shown on the label. Peak Power is defined as the watt peak at Standard Test Conditions (1000W/m2 irradiance, AM1.5, 25C. SOMS current, LACCS FF and Voltage from NREL calibration), as described in IEC61215, measured per IEC60904, and accounting for 3% measurement tolerance. SunPower modules shall, in any event, require a sweep rate of no less than 200ms to ensure an accurate power measurement. SunPower can provide a detailed testing procedure or a list of recognized testing agencies upon request.
Minimum Peak Power is defined as the minimum rated power, as shown on the label. Peak Power is defined as the watt peak at Standard Test Conditions (1000W/m2 irradiance, AM1.5, 25C. SOMS current, LACCS FF and Voltage from NREL calibration), as described in IEC61215, measured per IEC60904, and accounting for 3% tolerances. Maxeon Solar modules shall, in any event, require a sweep rate of no less than 200ms to ensure an accurate power measurement. Maxeon Solar can provide a detailed testing procedure or a list of recognized testing agencies upon request.
e) In cases of PV Module replacement, any replaced PV Module shall pass into the ownership of Maxeon Solar.
Minimum Peak Power is defined as the minimum rated power, as shown on the label. Peak Power is defined as the watt peak at Standard Test Conditions (1000W/m2 irradiance, AM1.5, 25C. SOMS current, LACCS FF and Voltage from NREL calibration), as described in IEC61215, measured per IEC60904, and accounting for 3% measurement tolerance. SunPower modules shall, in any event, require a sweep rate of no less than 200ms to ensure an accurate power measurement. SunPower can provide a detailed testing procedure or a list of recognized testing agencies upon request.
a) PV Modules subjected to: (i) misuse, abuse, neglect or accident; (ii) alteration or improper installation (improper installation includes, without limitation, installation or array that does not comply with all SunPower installation instructions and operations and maintenance instructions of any type (as may be amended and updated from time to time at SunPower’s sole discretion), and all national, state, and local laws, codes, ordinances, and regulations); (iii) repair or modification by someone other than an approved service technician of SunPower; (iv) conditions exceeding the voltage, wind, snow load specifications; and any other operational specification; (v) power failure surges, lightning, flood, or fire; (vi) damage from persons, insects, animals, or industrial chemical exposure; (vii) glass breakage from impact or other events outside SunPower’s control.
b) Cosmetic effects stemming from normal wear and tear of PV Module materials or other cosmetic variations which do not cause power output lower than what is guaranteed by the Limited Warranty. Normal wear and tear of PV Module materials can include, but is not limited to, fading of frame color, weathering of glass coatings, and areas of discoloration around or over individual solar cells or any part of the PV Module.
c) PV Modules installed in locations, which in SunPower’s absolute judgment may be subject to direct contact with bodies of salt water.
d) PV Modules for which the labels containing product type or serial number have been altered, removed or made illegible.
e) PV Modules which have been moved from their original installation location without the express written approval of SunPower.
f) SunPower modules which include “COM” in the model number. SunPower shall not be held responsible or liable to the customer or any third‐party arising out of any non‐performance or delay in performance of any terms and conditions of sale, including this Limited Warrant...
Examples of Minimum Peak Power in a sentence
The DC power of the AC Modules will be at least 98% of the Minimum Peak Power2 rating for the first year, and will decline by no more than 0.25% per year for the following 24 years; thus the DC power output at the end of the final year of the 25th year warranty period will be at least 92% of the Minimum Peak Power rating (the “Guaranteed Peak Power” rating) and the AC power output of the system will be at least 90% of the Peak System Power3 for the full 25-year warranty period.
The DC power of the AC Modules will be at least 98% of the Minimum Peak Power2 rating for the first year, and will decline by no more than 0.25% per year for the following 24 years; thus the DC power output at the end of the final year of the 25th year warranty period will be at least 92% of the Minimum Peak Power rating (the “Guaranteed Peak Power” rating) and the AC power of the system will be at least 90% of the Peak System Power3 for the full 25‐year warranty period.
More Definitions of Minimum Peak Power
Minimum Peak Power means Peak Power minus the Peak Power tolerance (as specified in Supplier’s Product datasheet). “Peak Power”, for this purpose is the power in peak ▇▇▇▇▇ that a PV module generates at standard test conditions, which is irradiance of 1000 W/m2, light spectrum AM 1.5, and a cell temperature of 25 degrees C.
Minimum Peak Power is defined as the minimum rated power, as shown on the label. Peak Power is defined as the watt peak at Standard Test Conditions (1000W/m2 irradiance, AM1.5, 25C. SOMS current, LACCS FF and Voltage from NREL calibration), as described in IEC61215, measured per IEC60904, and accounting for 3% measurement tolerance. SunPower modules shall, in any event, require a sweep rate of no less than 200ms to ensure an accurate power measurement. SunPower can provide a detailed testing procedure or a list of recognized testing agencies upon request. The Limited Warranty does not apply to any of the following:
a) PV Modules subjected to: (i) misuse, abuse, neglect or accident; (ii) alteration or improper installation (improper installation includes, without limitation, installation or array that does not comply with all SunPower installation instructions and operations and maintenance instructions of any type (as may be amended and updated from time to time at SunPower’s sole discretion), and all national, state, and local laws, codes, ordinances, and regulations); (iii) repair or modification by someone other than an approved service technician of SunPower; (iv) conditions exceeding the voltage, wind, snow load specifications, and any other operational specification; (v) power failure surges, lightning, flood, or fire; (vi) damage from persons, biological activity, or industrial chemical exposure; (vii) glass breakage from impact or other events outside SunPower’s control.
b) Cosmetic effects stemming from normal wear and tear of PV Module materials or other cosmetic variations which do not cause power output lower than what is guaranteed by the Limited Warranty. Normal wear and tear of PV Module materials can include, but is not limited to, fading of frame color, weathering of glass coatings, and areas of discoloration around or over individual solar cells or any part of the PV Module.
c) PV Modules installed in locations, which in SunPower’s absolute judgment may be subject to direct contact with bodies of salt water.
d) PV Modules for which the labels containing product type or serial number have been altered, removed or made illegible.
e) PV Modules which have been moved from their original installation location without the express written approval of SunPower.
f) PV Modules which have been installed on single-family homes or semi-detached homes, including but not limited to duplexes and townhomes. For clarity, apartment and condominiums are not excluded. SunPower ...
Minimum Peak Power is defined as the minimum rated power, as shown on the label. Peak Power is defined as the watt peak at Standard Test Conditions
Minimum Peak Power is defined as Peak Power minus peak power tolerance or the minimum rated power, as shown on the label. Peak Power is defined as the watt peak at Standard Test Conditions (1000W/m2 irradiance, AM1.5, 25C. SOMS current), as described in IEC61215, measured per IEC60904, and accounting for tolerances per EN50380. SunPower can provide a detailed testing procedure or a list of recognized testing agencies upon request.