In calibration definition

In calibration means making a reading with a calibrated test instrument within 6 inches of the site sensor. Verify that the sensor reading (via the permanent thermostat, gage or building automation system (BAS)) compared to the test instrument-measured value is within the tolerances specified in the prefunctional checklist requirements ( ). If not, install offset in BAS, calibrate or replace sensor. Use the same test instruments as used for the original calibration, if possible.
Sample 1Sample 2Sample 3
In calibration means observing a readout in the BAS and going to the actuator or controlled device and verifying that the BAS reading is correct. For items out of calibration or adjustment, fix now if easy, via an offset in the BAS, or a mechanical fix.
Sample 1Sample 2Sample 3
In calibration means making a reading with a calibrated test instrument within 6 inches of the site sensor.
Sample 1Sample 2Sample 3

Examples of In calibration in a sentence

  • In calibration, the model parameters have been chosen to minimize the quadratic errors between the model computed and the measured values of speed and flows.

  • In calibration of support equipment, the values realized by standards are established through the use of reference standards that are traceable to the International System of Units (SI).

  • To develop the Tamilian culture among the public through entertainment activities.

  • Presenting these graphs in the village meeting also provides a case for highlighting the importance of soil type, an important biophysical attribute of the farmer which can be used as proxy for prioritisation and targeting of the beneficiaries.

  • In calibration certificates the measurement result should be reported as y ± U associated with the units of y and U.

  • In calibration mode press to confirm factory calibration restore.• READ/ /TIMER: this is a multi-functional key.

  • Particulars and rationale for homework, projects, quizzes, exams, reading requirements, participation, due dates, etc.

  • In calibration, per methods, the values realized by standards are typically established using reference materials that are either purchased by the testing facility with a certificate of analysis or purity or prepared by the testing facility using support equipment that has been calibrated or verified to meet specifications.

  • In calibration of combined sewer overflow (CSO) volumes, Kleidorfer et al.

  • In calibration, two types of emotions were induced by the International Affective Digitized Sounds (IADS) methodology, developed by the Na- tional Institute of Mental Health Center for the Study of Human Emotion.


More Definitions of In calibration

In calibration means observing a readout in the BAS and going to the actuator or controlled device and verifying that the BAS reading is correct.
Sample 1Sample 2
In calibration means making a reading with a calibrated test instrument within 6 inches of the site sensor. Verify that the sensor reading (via the permanent thermostat, gage, or building automation system (BAS)) compared to the test instrument-measured value is within the tolerances specified in the Prefunctional Checklist requirements
Sample 1
In calibration means observing a readout in the BAS and going to the actuator or controlled device and verifying that the BAS reading is correct. For items out of calibration or adjustment, corrections may be applied in realtime during testing via an offset in the BAS or a mechanical fix if time permits, or be recorded in the Issues Log for follow-up by the construction team. Device or Actuator Procedure/ State BAS Value Instrument Measured/O bserved Value Pass Y/N Notes B-1 ISO Valve- Open Close - - - [1] B-2 ISO Valve- Open Close - - - [1] B-1 ON OFF On On Y B-2 ON OFF On On Y [2] B1&2 Relief Valves - - - - SAMPLE **For every actuator or device originally found out of calibration, check one additional one not listed. Notes:
Sample 1

Related to In calibration

  • Calibration means the determination of (1) the response or reading of an instrument relative to a series of known radiation values over the range of the instrument, or (2) the strength of a source of radiation relative to a standard.

  • Recalibration means the adjustment of all DRG weights to reflect changes in relative resource consumption.

  • Calibration gas means a gas mixture used to calibrate gas analysers.

  • Process weight means the total weight of all materials introduced into any source operation. Solid fuels charged will be considered as part of the process weight, but liquid and gaseous fuels and combustion air will not.

  • Testing means that element of inspection that determines the properties or elements, including functional operation of materials, equipment, or their components, by the application of established scientific principles and procedures.

  • Sampling means the distribution of samples to members of the general public in a public place.

  • Assay means a laboratory analysis of Crude Petroleum to include the following: A.P.I. Gravity, Reid vapor pressure, composition, pour point, water and sediment content, sulfur content, viscosity, distillation, hydrogen sulfide, flash/boiling point and other characteristics as may be required by Carrier.

  • Meter means, unless otherwise qualified, a device that measures and registers the integral of an electrical quantity with respect to time.

  • Batch means a specific quantity of Product that is intended to have uniform character and quality, within specified limits, and is produced according to a single manufacturing order during the same cycle of manufacture.

  • Meters shall have the meaning set forth in Section 4.6(a) hereof.

  • Fluoroscopic imaging assembly means a subsystem in which X-ray photons produce a visual image. It includes the image receptor(s) such as the image intensifier and spot-film device, electrical interlocks, if any, and structural material providing linkage between the image receptor and diagnostic source assembly.

  • Instantaneous flow measurement means the flow measured during the minimum time required for the flow-measuring device or method to produce a result in that instance. To the extent practical, instantaneous flow measurements coincide with the collection of any grab samples required for the same sampling period so that together the samples and flow are representative of the discharge during that sampling period.

  • Test means such test as is prescribed by the particulars or considered necessary by the Inspecting Officer whether performed or made by the Inspecting Officer or any agency acting under the direction of the Inspecting Officer;

  • Outputs means the goods or services that are produced by an entity or other person;

  • Installation inspector means a person who, by reason of his knowledge of the physical sciences and the principles of engineering, acquired by a professional education and related practical experience, is qualified to supervise the installation of tank systems.

  • API Gravity means gravity determined in accordance with ASTM Designation D-287-92 or latest revision thereof.

  • Technique factors means the following conditions of operation:

  • Smoke detector means a device which detects particles or products of combustion other than heat.

  • Tests means and include such test or tests to be carried out on the part of the contractor as are prescribed in the contract or considered necessary by BHEL, in order to ascertain the quality, workmanship, performance and efficiency of the contractor or part thereof.

  • Finished water means the water that is introduced into the distribution system of a public water system and is intended for distribution and consumption without further treatment, except as treatment necessary to maintain water quality in the distribution system (e.g., booster disinfection, addition of corrosion control chemicals).

  • Process Gas means gas used for which alternate fuels, other than another gaseous fuel, are not technically feasible such as in applications requiring precise temperature controls and precise flame characteristics.

  • Cost of materials means the cost of components, parts or materials which are intended for the production, manufacturing or assembling of the goods bid for and which are not produced, manufactured or assembled in the factory where the production, manufacture or assembly of such goods occurs, including freight, landing costs, port charges, import duties and other import costs of such components, parts or materials and all costs in connection with the handling and transport thereof prior to delivery at that factory;

  • Process Wastewater means any water which, during manufacturing or processing, comes into direct contact with or results from the production or use of any raw material, intermediate product, finished product, by-product, or waste product.

  • Semi-annual (2/Year) sampling frequency means the sampling shall be done during the months of June and December, unless specifically identified otherwise.

  • Scaling as used herein, involves:

  • Hydraulic fracturing means the fracturing of underground rock formations, including shale and non-shale formations, by manmade fluid-driven techniques for the purpose of stimulating oil, natural gas, or other subsurface hydrocarbon production.