Disarm definition

Disarm. “Switch” or “Follow” comply only when activated by keyswitches with more than 10,000 code combinations. An input is set up for system fault management. For zones with the “Fault zone” option enabled, it is necessary to eliminate from the relative alarm event the programming of an external sounder/flasher in the “Outputs” parameter. You can program indoor sounder/flashers via the “Other outputs” option. The system must include a self-powered outdoor sounder/flasher for intrusion-alarm event signalling. The telephone dialer must be enabled. If a digital telephone dialer is used for transmissions or a voice dialer with a SmartLogos30M board, a channel and a phone number must be reserved for the following events: • All events generated by zones with the “Hold-up” attribute. • All events generated by: “Instant”, “Delayed”, “Delayed unhidden” and “Route” • All events generated by terminal, peripheral and control panel tamper. • All faults detected by the control panel. The “Alarm Cycles” parameter of each zone must be set between 3 and 10. The “Mains fail.Delay” parameter must be set at no more than 1 minute. The “Entry Time” of each partition must be set at a maximum of 45 seconds. You must enable the “Priority” option for any alarm events associated with “Hold-up” zones. Compliance with rules in force 87 “Failed to arm” and “Forced arming” events must be saved to the Events log. The programmed “LowBattery delay” must not be programmed at more than 5 minutes.
View Source
Disarm. Disarmed", and "Disarming" means disabling the functionality of the FFR such that the under frequency relay or control system does not operate when the target frequency of fifty nine point five (59.5) Hz is reached or a SCADA Response Signal is received.
View Source
Disarm. Disarmed", and "Disarming" means disabling the functionality of the LSSi such that the under frequency relay is not continuously measuring system frequency and does not operate when the target frequency of fifty nine point five (59.5) Hz is reached or a SCADA Trip Signal is received.
View Source

Examples of Disarm in a sentence

  • When Auto Disarm is enabled, it is similar to discretionary trading in that you decide when to trade and when to not trade.

  • Auto Disarm On/Off Default = Off Turning this mode On means that the algo will automatically Disarm (i.e. not enter any trades) immediately after the last algo- generated trade is closed.

  • The Arm/Disarm option in the dropdown menu only appears when in Auto Disarm mode.

  • This is what it looks like when the algo is Armed: When you switch back to normal auto trading mode (by turning off Auto Disarm Mode in the parameters window), the above menu option for changing the Arm state will no longer be visible in the dropdown menu.

  • When in Auto Disarm Mode, you can control whether the algo is Armed or Disarmed by accessing the User Interface (UI) dropdown menu, where you will find a menu option to select the Arm state: When you first enable the algo, in Auto Disarm Mode, the algo will be initially Disarmed.

  • The end result of using Auto Disarm Mode is that you decide when the conditions are right for engaging in the market and only then will the algo take a trade when the next signal occurs.

  • Auto Disarm Mode is activated simply by checking the box next to the Auto Disarm parameter in the Entries section of the parameters window: You can revert back to continuous fully automated trading by unchecking that box.

  • If turned On, the algo will Disarm after each trade and then you have to re-Arm the algo before a new trade can be taken.

  • Once a trade is entered in Auto Disarm Mode, the algo automatically Disarms immediately after that trade closes.

  • Contact ID Check box to indicate the Contact-ID code associated with the zone for the occurrence or restoral of events such as: • Zone alarm • Zone tamper • Zone real-time Type Dropdown box for the selection of the zone type: Instant, Delayed, 24hour, Technological, Arm, Disarm, Switch, Follow Balancing Dropdown box for the selection of the balancing type (the options vary in accordance with the zone type).


More Definitions of Disarm

Disarm. Disarmed", and "Disarming" means disabling functionality of the LSSi such that no load shedding happens as a result of a frequency deviation or if a SCADA Trip Signal is received.
View Source

Related to Disarm

  • Technically Evaluated Entity means the company which has been evaluated for the satisfaction of the technical requirement set forth in Clause 2.1.2 hereof;

  • Encounter Data Any Contractor accessing payments for services through the Global Commitment to Health Waiver and Vermont Medicaid programs must provide encounter data to the Agency of Human Services and/or its departments and ensure that it can be linked to enrollee eligibility files maintained by the State.

  • Socially and economically disadvantaged person means an individual who is a citizen or lawful permanent resident of the United States and who is Black, Hispanic, Native American, Asian, Female; or a member of another group or an individual found to be disadvantaged by the Small Business Administration pursuant to Section 3 of the Small Business Act.

  • Disadvantaged Worker means any person who:

  • AT&T-12STATE means the AT&T owned ILEC(s) doing business in Arkansas, California, Illinois, Indiana, Kansas, Michigan, Missouri, Nevada, Ohio, Oklahoma, Texas and Wisconsin.