Cable Specifications definition

Cable Specifications means the drawings and specifications regarding the Cable hardware and materials incorporated into the construction project.
Sample 1Sample 2Sample 3
Cable Specifications means the drawings and specifications regarding the Cable, the Cable Accessories, and related hardware and materials to be employed in the installation of the Cable.
Sample 1Sample 2Sample 3
Cable Specifications. The cable furnished shall conform to the Cable descriptions included below. CABLE TYPE DESCRIPTION Medium 25,000 and 5000 volts, single-conductor and three Voltage conductor with ground, Class B stranded copper; Power ethylene propylene rubber (EPR) insulation; shielded; and chlorosulfonated polyethylene (CSP) or chlorinated polyethylene (CPE) jacketed. Kerite is the preferred manufacturer. Low Voltage 600 volts, single-conductor, Class B stranded Power copper; EPR or XLP insulated; CPS or CPE jacketed. Low Voltage 600 volts, three-conductor; concentric lay, Power stranded copper with a ground wire in the interstices; FRXLPE or FREPR insulation; CSP or CPE jacketed overall Control Control cable, 600 volt, multiple-conductor, as required, stranded copper, 10 AWG, 12 AWG, 14 AWG; multiple-conductor, XLP insulation; CSP or CPE jacketed overall. Thermocouple Thermocouple extension cable, one, four, six and eight twisted pairs. Solid alloy conductor with the same material as the thermocouples, with shield over each pair (except for one-pair construction) and with an overall shield, 16 AWG single pair; 20 AWG multi pair; FRXLPE or FREPR insulation; aluminum mylar tape shield with drain wire; CSP or CPE jacketed overall. Instrumenta- Instrumentation cable, 300 V minimum, flame tion retardant single and multiple twisted pairs and triads, shielded instrument cable with individually shielded pairs, overall shield, and overall jacket; FRXLPE or FREPR insulation; CSP or CPE jacketed overall. (Single pair or triad 16AWG, multi pair or triad 18AWG) High High temperature control and fixture wire, single- Temperature conductor control cable; stranded copper; 12 AWG; Fixture stranded copper, with normal maximum operating Wire temperature of 200 C; silicone rubber insulation; braided glass jacket. Lighting & Lighting circuit runs totally enclosed in conduit, Receptacles NEC Type RHH-RHW-USE with XLPE insulation for use in outdoor or unheated areas.
Sample 1

Examples of Cable Specifications in a sentence

  • Cable Specifications: All cables shall be as per latest IS 1554 Part I PVC insulated heavy duty electric cables Part I for working Voltages up to and including 1100 V.All power cables shall be PVC insulated, armored, inner sheathed, PVC insulated aluminum conductor.

  • Fiber Optic Cabling1) Cable and Fiber Count - If more than one LTER is required, fiber optic cabling shall be installed between LTERs. One fiber-optic cable containing a minimum of 12 fibers (6 pairs) shall interconnect LTERs.2) General Fiber-Optic Cable Specifications - All fiber-optic cables and individual fibers shall meet or exceed the following specifications.

  • All System Materials shall comply with the Cable Specifications and shall meet the specifications described in the Working Drawings.

  • Cable and Fiber Count - If more than one LTER is required, fiber-optic cabling shall be installed between LTERs. One fiber-optic cable containing a minimum of 12 fibers (6 pairs) shall interconnect LTERs.b. General Fiber-Optic Cable Specifications - All fiber-optic cables and individual fibers shall meet or exceed the following specifications.

  • With 4–wire cable, the maximum synchronous data rate is 460 Kbps.For more information concerning cable types, lengths, and baud rates, refer to ”128–Port Asynchronous Adapter Cable Specifications and Cabling Scenarios”, on page 6-7.

  • Technical Systems Bulletin Additional Cable Specifications for Unshielded Twisted-Pair Cables”.

  • The analysis is most sensitive to variations in emission factors for both the baseline emission rates and the impact of technology in reducing emissions.

  • Each of PG&E and IPN shall cause their respective contractors, subcontractors and agents who perform work to install the System (including, without limitation the Contractor) to warrant their work in accordance with industry standards and practices and the terms of this Agreement (including, without limitation, the Cable Specifications).

  • Labor and Industry will have no financial liability for the maintenance or service of those systems during the lease period.Table of Contents7.1 Backbone or Riser Cable Specifications 17.2 Station Cable Specifications 17.3 Preferred Manufacturers Cabling System Components 2The following voice cable specifications are to be followed for the installation of voice riser and voice station cabling at all new or renovated Labor and Industry Offices.

  • Adherence to the VA Network Cable Specifications by cabling installation contractors is a condition of contract.

Related to Cable Specifications

  • Contract Specifications means the principal trading terms in CFD (for example Spread, Swaps, Lot Size, Initial Margin, Necessary Margin, Hedged Margin, the minimum level for placing Stop Loss, Take Profit and Limit Orders, financing charges, charges etc) for each type of CFD as determined by the Company from time to time.

  • technical specification means a document that prescribes technical requirements to be fulfilled by a product, process or service;

  • Specifications means the Specifications of the Works included in the Contract and any modification or addition made or approved by the Project Manager.

  • Specification Schedule means the Schedule containing details of the Specification.