Test piece Sample Clauses

A "Test piece" clause defines the requirements and procedures for submitting a sample or prototype of goods or work for inspection and approval before full-scale production or delivery. Typically, this clause specifies the standards the test piece must meet, the process for evaluation, and the consequences if the test piece fails to comply, such as requiring modifications or rejecting the work. Its core function is to ensure that the final deliverables will meet agreed-upon quality or performance standards, thereby reducing the risk of defects or misunderstandings later in the project.
Test piece. The test piece shall be a flat square of side 300 + 10/-0 mm or shall be cut from the flattest part of a windscreen or other curved pane. Alternatively a curved pane may be tested. In this case care shall be taken to ensure adequate contact between the safety glazing and the support.
View SourceView Similar (14)
Test piece. The test piece shall be a flat square of side 300 +10/-0 mm or shall be cut out from the flattest part of a windscreen or other curved pane of safety glazing. Alternatively, the whole windscreen or other curved pane of safety glazing may be tested. In this case care shall be taken to ensure adequate contact between the safety glazing pane and the support." E/ECE/324 Rev.1/Add.42/Rev.1/Amend.1 Regulation No. 43 page 18 3.1. Headform test without deceleration measurement 3.1.1. Apparatus Headform weight with a spherical or semi-spherical headform made of ...". Paragraph 3.2., renumber as paragraph 3.1.4. Paragraph 3.3., renumber as paragraph 3.1.5.
View Source
Test piece. Alternatively a curved pane of safety glazing may be tested. In this case care shall be taken to ensure adequate contact between the safety glazing and the support.
View Source
Test piece. The test piece shall be a flat square of side 300 Í q mm ^ o r shall be cut out from the flattest part of a windscreen or other curved pane of safety glass.
View Source

Related to Test piece

  • Test The outer surface of the lamp lenses shall be subjected once or more than once to the action of the sand jet produced as described above. The jet shall be sprayed almost perpendicular to the surface to be tested. The deterioration shall be checked by means of one or more samples of glass placed as a reference near the lenses to be tested. The mixture shall be sprayed until the variation in the diffusion of light on the sample or samples measured by the method described in Appendix 2, is such that: Δ d = (T5 - T4) / T2 ≤ 0.0250 ± 0.0025 Several reference samples may be used to check that the whole surface to be tested has deteriorated homogeneously.

  • Meter Testing Company shall provide at least twenty-four (24) hours' notice to Seller prior to any test it may perform on the revenue meters or metering equipment. Seller shall have the right to have a representative present during each such test. Seller may request, and Company shall perform, if requested, tests in addition to the every fifth-year test and Seller shall pay the cost of such tests. Company may, in its sole discretion, perform tests in addition to the fifth year test and Company shall pay the cost of such tests. If any of the revenue meters or metering equipment is found to be inaccurate at any time, as determined by testing in accordance with this Section 10.2 (Meter Testing), Company shall promptly cause such equipment to be made accurate, and the period of inaccuracy, as well as an estimate for correct meter readings, shall be determined in accordance with Section 10.3 (Corrections).

  • Statistical Sampling Documentation a. A copy of the printout of the random numbers generated by the “Random Numbers” function of the statistical sampling software used by the IRO.‌ b. A description or identification of the statistical sampling software package used by the IRO.‌

  • Test procedure The engine speed shall be gradually increased from idle to the target engine speed, not exceeding the tolerance band of ±3 per cent of the target engine speed, and held constant. Then the throttle control shall be rapidly released and the engine speed shall be returned to idle. The sound pressure level shall be measured during a period of operation consisting of a maintaining constant engine speed of 1 second and throughout the entire deceleration period. The maximum sound level meter reading during this period of operation, mathematically rounded to the first decimal place, is taken as the test value.

  • Random Testing Notwithstanding any provisions of the Collective Agreement or any special agreements appended thereto, section 4.6 of the Canadian Model will not be applied by agreement. If applied to a worker dispatched by the Union, it will be applied or deemed to be applied unilaterally by the Employer. The Union retains the right to grieve the legality of any imposition of random testing in accordance with the Grievance Procedure set out in this Collective Agreement.