Specification Requirements Clause Samples

Specification Requirements. Specifications shall be written in the Master Format 2016. Provide a copy of all Documents in Microsoft Word release 2013, before request for final payment is sent to Owner.
View SourceView Similar (3)
Specification Requirements. The specifications must be in the full Construction Specifications Institute (CSI) Division Three-Part Format as established in the CSI Manual of Practice covering required materials, products, and equipment, their installation and operation, quality assurances, reference standards, and submittal requirements. The specifications must provide all supplemental information and requirements included but not elsewhere covered by the Contract Documents. The Design Professional should ensure that the specifications do not conflict with the terms of the CM/GC Construction Contract.
View SourceView Similar (2)
Specification Requirements. These specifications apply to all components of Contractor vehicles unless otherwise stated within specifications.
View Source
Specification Requirements. Purchaser shall use commercially reasonable efforts to develop and agree with the Designated Employees the complete set of specifications for the Drivers.
View Source
Specification Requirements. The Supplier must deliver and fulfil all of the mandatory service requirements as listed for the RM6102 Apprenticeship Training Dynamic Marketplace (DMP) Agreement which can be found in the CCS Framework document, RM6102 Customer Needs document.
View Source
Specification Requirements. If requested, awarded Contractor(s) must provide trained staff and personnel to perform fitting, measurement and consultative services on-site at the purchasing agency’s facilities/locations.
View Source
Specification Requirements. Contractor shall furnish and deliver quicklime (calcium oxide, CaO) to the City of Ocala Water Treatment Plant #1 elevated lime storage silo located at ▇▇▇▇ ▇▇ ▇▇▇▇ ▇▇▇▇▇▇, ▇▇▇▇▇ ▇▇ ▇▇▇▇▇. This product must be commercial grade (NSF) quicklime and adhere to the specification requirements below: Quicklime must be pebble and/or rice lime, 1/2” inch x 1/8” inch, in accordance with the following: • The quicklime shall contain not less than ninety percent (90%) available calcium oxide and shall comply with the provisions of AWWA B202. • The quicklime shall be NSF commercial grade.
View Source
Specification Requirements. Inspection and repairs – The successful Vendor, during normal business hours, shall periodically inspect the equipment two (2) times per year for the term of this contract. Inspections shall be limited to the following (as applicable).
View Source
Specification Requirements. The Colocated Device and any Spare must be fully compatible with data center specifications for physical space, security, refrigeration and power ("Specification Requirements"), including without limitation: 4.1 Designed to be natively rack-mountable, and accompanied by mounting hardware that does not alter the manufacturer's intended mounting specifications; 4.2 Dimensions are not in excess of the physical space available for the configuration in the data center; 4.3 Weight, including attachments and mounting hardware, is not in excess of that allowed in the data center; 4.4 Special or external cooling or ventilation systems or any that are based on liquids or gas are not required; 4.5 Operates normally without any modifications at the standard voltage supplied by the data center; 4.6 Complies with the acceptable range of power consumption proportional to the required physical space; 4.7 A rack-mountable firewall provided and managed by us protects the configuration; 4.8 Functions using Network Address Translation behind the perimeter firewall; 4.9 Is not intended to be deployed in-line between other devices, whether or not such devices are provided by us; 4.10 Supports the 10 Base-T or 100 Base-TX Ethernet standards as its main media type for management, operation or any other purpose; 4.11 Is not intended to be connected directly to another server or colocated device; 4.12 Network connections are always made to an Ethernet switch operated by us; 4.13 To the extent that it is intended for termination of a cross-connected circuit, the requirements and details of such are subject to evaluation and approval by us; 4.14 Does not contain any software (unless such software has been permanently disabled), internal hardware or attachment capable of capturing sound, images, video, motion or chemical composition; and 4.15 Neither the Colocated Device nor any of its components or attachments is capable of receiving or transmitting any type of signal using radio frequency, microwaves, infrared or any other type of wireless carrier signal. Upon its delivery to the data center, we may inspect the Colocated Device, including disassembly in its discretion, to ascertain whether all of the Specification Requirements have been met. Unless performed in a grossly negligent manner, such inspection shall be without liability to us. All references herein to Colocated Device include the Spare, if any.
View Source

Related to Specification Requirements

  • Notification Requirements 1. If the Family Leave is foreseeable, the employee must provide the agency/department with thirty (30) calendar days notice of his or her intent to take Family Leave. 2. If the event necessitating the Family Leave becomes known to the employee less than thirty (30) calendar days prior to the employee's need for Family Leave, the employee must provide as much notice as possible. In no case shall the employee provide notice later than five (5) calendar days after he or she learns of the need for Family Leave. 3. For foreseeable leave due to a qualifying exigency, an employee must provide notice of the need for leave as soon as practicable, regardless of how far in advance such leave is foreseeable. 4. When the Family Leave is for the purpose of the scheduled medical treatment or planned medical care of a child, parent, spouse or registered domestic partner, the employee shall, to the extent practicable, schedule treatment and/or care in a way that minimizes disruption to agency/department operations.

  • Certification Requirements The applicant will provide Vista Laboratories, Inc. with all product information for the evaluation of the product to be certified and warrant that the information provided is accurate and complete so that Vista Labs may perform the services requested. If the product was tested at an external laboratory, the applicant must provide the complete test report to Vista Labs. If the external testing facility is not ISO 17025 accredited, or does not have the proper scope, Vista Labs must determine if the test report can be used for certification activities. The applicant’s information is used to perform a product review and evaluation to determine the product’s compliance to the specific certification requested. Throughout the process, the client agrees to make claims regarding certification consistent with the scope of certification. The applicant agrees to supply the required number of product samples, to be determined by Vista Labs, to the laboratory for testing, measurement, and evaluation purposes. The client understands that certain tests may damage or destroy the sample and acknowledge that Vista Labs is not responsible for such damages. Samples will be returned only upon request by the applicant and at the applicant’s expense, after the completion of certification. Samples will be disposed of after six months if not requested for return by applicant. The product is ineligible for certification if it has been modified by the client after testing or certification. Changes to the product must be approved by Vista Laboratories. Vista Labs reserves the right to re- evaluate the product as a result of information that raises questions concerning the conformance of the product. Certified products maintain fulfilment of product requirements if the certification applies to ongoing production. If the client provides copies of the certification documents to other parties, the documents are reproduced in their entirety, or as specified in the certification scheme. In making reference to its product certification in media, such as brochures or advertisement, the client complies with the requirements of the Vista Labs or as specified by the certification scheme. The client complies with any requirements that may be prescribed in the certification scheme relating to the use of marks of conformity, and on all product correspondences and product related information. Vista Labs reserves the right to revise or withdraw the requirements as required in order to maintain conformance with FCC rules and regulations governing the product. The product may continue with certification and receive certification upon demonstration of compliance with the revised requirements, to the satisfaction of Vista Laboratories.