Common use of REMOVAL OF EXISTING WORK Clause in Contracts

REMOVAL OF EXISTING WORK. Hack up/off and remove ceramic tiles including removing mortar bed or adhesive from concrete or brickwork and preparing surface for new screed, plaster, tile finish, etc. Breaking up 100mm thick reinforced concrete thick m3 1 Breakdown 110mm brickwall m2 1 Ditto but to 220mm brickwall m2 1 Hack-up plaster work m2 1 Tiles to floors m2 1 Taking out and removing piping, sanitary fittings, etc including disconnecting piping from fittings and making good floor and wall finishes (making good tiling and paintwork elsewhere) Remove wash hand basins plugged to wall No 1 Remove toilet seat fixed to floor complete including cistern No 1 Steel urinal approximately 1000 x 1000mm high, Complete No 1 Taking down and removing roofs, floors, panelling, ceiling Gypsum plasterboard ceilings including cornices, timber brandering,etc m2 1 Take out and remove doors, windows, etc including thresholds. xxxxx, etc and prepare to receive new doors, frames, windows, etc. (all elswhere measured Timber single door, Door lockset including, handles, etc No 1 Taking out and removing glass and mirrors Panes exceeding 0,1m2 and not exceeding 0,5m2 (new glazing elsewhere measured) Item 1 Making good face brickwork Wash down existing face bricks wall with approved soap/acid and pressure hose Item 1 Carried to Final Summary MAINTENANCE OF FLUSHING TOILETS - SCHEDULE OF RATES Description Unit Quantity Rate Amount SECTION B BILL No.1 PLUMBING & DRAINAGE (PROVISIONAL) Class 2 Copper pipes 15mm pipe and fixing to walls etc including any necessary holderbats fixings etc m 1 28mm Ditto m 1 15mm Pipe chased into brickwork m 1 22mm Ditto m 1 28mm Ditto m 1 Extra Over copper pipes for brass compression fittings 15mm fittings No 1 22mm Ditto No 1 28mm Ditto No 1 50mm diameter uPVC pipes with solvent welded straight joints including all excavations not exceeding 1m deep m 1 Ditto but 110mm m 1 Extra Over uPVC pipes for 50mm straightb reducer solvent welded fittings No 1 Ditto but 50mm plain bend No 1 Ditto but 110mm plain bend No 1 Ditto 50mm access bend No 1 Ditto 50mm plain junction No 1 Ditto 110mm plain junction No 1 Ditto but 50mm access junction No 1

REMOVAL OF EXISTING WORK. Hack up/off and remove ceramic tiles including removing mortar bed or adhesive from concrete or brickwork and preparing surface for new screed, plaster, tile finish, etc. Breaking up 100mm thick reinforced concrete thick m3 1 Breakdown 110mm brickwall m2 1 Ditto but to 220mm brickwall m2 1 Hack-up plaster work m2 1 Tiles to floors m2 1 Taking out and removing piping, sanitary fittings, etc including disconnecting piping from fittings and making good floor and wall finishes (making good tiling and paintwork elsewhere) Remove wash hand basins plugged to wall No 1 Remove toilet seat fixed to floor complete including cistern No 1 Steel urinal approximately 1000 x 1000mm high, Complete No 1 Taking down and removing roofs, floors, panelling, ceiling ceilings, partitions, etc 1 Gypsum plasterboard ceilings including cornices, timber brandering,etc , etc. in patches m2 1 Take 5 2 Carefully take out and remove doors, windows, etc including thresholds. xxxxx, etc and prepare to receive new doors, frames, windows, etc. (all elswhere measured Timber single door, Door lockset including, handles, etc No 1 Taking worn out and removing glass damaged roofing drive screws or hook bolts and mirrors Panes exceeding 0,1m2 replace with new heavy duty, hot dipped galvanised fixings with self sealing polypropylene washers and not exceeding 0,5m2 seals (new glazing elsewhere measuredapproximately 7 no. fixings per square meter on roofing) Item m2 90 MAKING GOOD OF FINISHES ETC Carried Forward R Section No. 2 Bill No. 1 Alterations Brought Forward R Making good face brickwork Wash down internal cement plaster 3 Walls in patches m2 22 Stitching existing face bricks brick walls 4 10 x 30 x 0.5mm 'Menlath' mesh strips 205mm wide fixed by shot pinning or nail fixing to masonry walls over cracks exceeding 0.5mm but exceeding 2mm extending 100mm to either side of crack to both faces of the masonry wall with approved soap/acid and pressure hose m 21 Carried Forward to Summary of Section No. 2 Section No. 2 Bill No. 1 Alterations R Item 1 Carried to Final Summary MAINTENANCE OF FLUSHING TOILETS - SCHEDULE OF RATES Description No BILL NO. 2 Unit Quantity Rate Amount SECTION B BILL No.1 PLUMBING & DRAINAGE (PROVISIONAL) Class 2 Copper pipes 15mm pipe CEILINGS, PARTITIONS AND ACCESS FLOORING PREAMBLES The descriptions given in the various items below are not necessarily full and fixing complete and reference must be made to walls etc including any necessary holderbats fixings etc m 1 28mm Ditto m 1 15mm Pipe chased into brickwork m 1 22mm Ditto m 1 28mm Ditto m 1 Extra Over copper pipes the "Model Preambles To All Trades 2008", "Supplementary Preambles" and "Supplementary Specifications" to this contract for brass compression the full requirements of each scheduled item SUPPLEMENTARY PREAMBLES Openings in ceilings for light fittings 15mm fittings No 1 22mm Ditto No 1 28mm Ditto No 1 50mm diameter uPVC pipes etc. are to include for additional suspension as required Ceilings Unless otherwise decribed ceilings shall be deemed to be horizontal Fixings Items described as "nailed" shall be deemed to be fixed with solvent welded straight joints including all excavations hardened steel nails or shot pinned to blockwork or concrete. Items described as "plugged" shall be deemed to include screwing to fibre, plastic or metal plugs at not exceeding 1m deep m 1 Ditto but 110500mm m 1 Extra Over uPVC pipes for 50mm straightb reducer solvent welded fittings No 1 Ditto but 50mm plain bend No 1 Ditto but 110mm plain bend No 1 Ditto 50mm access bend No 1 Ditto 50mm plain junction No 1 Ditto 110mm plain junction No 1 Ditto but 50mm access junction No 1centres, and where described as "bolted", the bolts have been given elsewhere FLUSH PLASTERED SUSPENDED CEILINGS

REMOVAL OF EXISTING WORK. Hack up/Breaking up and removing reinforced concrete including cutting off and remove ceramic tiles removing reinforcement 1 170mm Thick surface beds m2 15 Carried Forward R Section No. 3 Bill No. 1 Alterations Brought Forward R 2 700mm Thick Steps and Platform m2 2 Carried Forward R Section No. 3 Bill No. 1 Alterations Brought Forward R Breaking down and removing brickwork etc and making good ends, including all necessary temporary propping 3 Half brick walls m2 62 4 One brick walls m2 88 Taking out and removing mortar bed or adhesive doors, windows, etc from concrete or brickwork brickwork, and preparing surface for make wall good to receive new screeddoors, plaster, tile finishwindows, etc. Breaking 5 Single timber door and frame size 813 x 2 032mm high No 2 6 Timber window size 455 x 1200mm high overall No 1 7 Timber window size 500 x 1600mm high overall No 2 8 Timber window size 900 x 1005mm high overall No 2 9 Timber window size 1000 x 2000mm high overall No 7 Taking out and removing doors, windows, etc from brickwork to be demolished 10 Single door and frame size 813 x 2 032mm high No 6 11 Double door and frame size 1511 x 2 032mm high No 1 Taking out and removing doors, windows, etc, including thresholds, xxxxx, etc and building up 100openings in brick walls, including making good plaster and paint on both sides 12 Single door and frame size 813 x 2 032mm thick reinforced concrete thick m3 high No 1 Breakdown 110Taking down and removing roofs, floors, panelling, ceilings, partitions, etc 13 Pitched corrugated iron roof 146m2 (measured on plan) and a maximum of 3.70m high extreme, including roof covering, timber trusses and purlins, xxxxx soffit covering, fascias, barge boards, ceilings, gutters, rainwater pipes, etc. No 1 Carried Forward R Section No. 3 Bill No. 1 Alterations Brought Forward R Taking out and removing sundry joinery work, fittings, etc 14 Timber dado wall rails m 57 15 Timber architraves from wall m 11 16 Timber floor and structure suspended approximately 1000mm brickwall above ground level, including all skirting, timber joists, bearers and floor boards. m2 1 Ditto but to 220mm brickwall m2 1 Hack-up plaster work m2 1 Tiles to floors m2 1 109 Taking out and removing piping, sanitary fittings, etc etc, including disconnecting piping from fittings and making good floor and wall finishes (making good tiling and paintwork elsewhere) Remove 17 Vitreous china wash hand basins plugged to wall No 1 Remove toilet seat fixed to floor complete basin, including cistern No 1 Steel urinal approximately 1000 x 1000mm high, Complete No 1 Taking down and removing roofs, floors, panelling, ceiling Gypsum plasterboard ceilings including cornices, timber brandering,etc m2 1 Take out and remove doors, windows, etc including thresholds. xxxxx, etc and prepare to receive new doors, frames, windows, etc. (all elswhere measured Timber single door, Door lockset including, handlespiping, etc No 1 Taking out 18 Vitreous china WC pan with flush valve No 1 19 Vitreous china wall hung urinal with flush valve No 1 20 Stainless steel single bowl sink No 1 Hacking up/off and removing glass granolithic, screeds, plaster, etc from concrete or brickwork and mirrors Panes exceeding 0,1m2 preparing surfaces for new screed, plaster, tile finishes, etc 21 Internal plaster from walls and not exceeding 0,5m2 (columns m2 200 22 External plaster from walls, columns and beams m2 165 BUILDING UP OPENINGS Brickwork in NFP bricks in class II mortar in building up openings 23 One brick walls m2 2 Sundries 24 Cutting toothing and bonding new glazing elsewhere measured) brickwork to existing m2 15 Carried Forward to Summary of Section No. 3 R Section No. 3 Bill No. 1 Alterations Item 1 Making good face brickwork Wash down existing face bricks wall with approved soap/acid and pressure hose Item 1 Carried to Final Summary MAINTENANCE OF FLUSHING TOILETS - SCHEDULE OF RATES Description Unit No BILL NO. 2 Quantity Rate Amount SECTION B BILL No.1 PLUMBING & DRAINAGE EARTHWORKS NOTES: Attention is directed to the relevant sections of the Model Preambles for Trades (PROVISIONAL2008 edition) Class 2 Copper pipes 15mm pipe as published by the Association of South African Quantity Surveyors, which form part of this Bill of Quantities and fixing must be read in conjunction therewith. SUPPLEMENTARY PREAMBLES Excavation in adverse soil conditions. Should the contractor encounter soft or hard rock or any other adverse soil conditions, during the excavation the tenderer shall inform the Engineer / Principal Agent and Client, immediately in order to walls etc including quantify the soft or hard rock in the excavation. No payments will be made for soft and rock excavations without the necessary measurement records issue by the Engineer / Principal Agent. The prices/ rates for excavations in all soil types shall include for digging out, any necessary holderbats fixings etc m 1 28mm Ditto m 1 15mm Pipe chased into brickwork m 1 22mm Ditto m 1 28mm Ditto m 1 Extra Over copper pipes staging as required, forming of falls, slopes curves, stepping etc. The trimming of sides, levelling of bottoms and watering the same to the satisfaction of the Engineer/ Principal Agent. Prices / rates shall include for brass compression fittings 15mm fittings No 1 22mm Ditto No 1 28mm Ditto No 1 50mm diameter uPVC pipes with solvent welded straight joints including bulking after excavations and consolidation of filling and for multiple handling of the excavated material as no allowance for bulking or consolidation or material has been allowed. Carting away of excavated material Descriptions of carting away of excavated material shall be deemed to include loading excavated material onto trucks directly from the excavations or, alternatively, from stock piles situated on the building site, all excavations not exceeding 1m deep m 1 Ditto but 110mm m 1 Extra Over uPVC pipes for 50mm straightb reducer solvent welded fittings No 1 Ditto but 50mm plain bend No 1 Ditto but 110mm plain bend No 1 Ditto 50mm access bend No 1 Ditto 50mm plain junction No 1 Ditto 110mm plain junction No 1 Ditto but 50mm access junction No 1material shall be disposed to a site of the contractor's choice. Carried Forward R Section No. 3 Bill No. 2 Earthworks Amount Brought Forward R

REMOVAL OF EXISTING WORK. Hack up/off and remove ceramic tiles including removing mortar bed or adhesive from concrete or brickwork and preparing surface for new screed, plaster, tile finish, etc. Breaking up 100mm thick reinforced concrete thick m3 1 Breakdown 110mm brickwall m2 1 Ditto but to 220mm brickwall m2 1 Hack-up plaster work m2 1 Tiles to floors m2 1 Taking out and removing piping, sanitary fittings, etc including disconnecting piping from fittings and prepare for new (elsewhere) and making good floor and wall finishes (making good tiling and paintwork elsewhere) Remove wash hand basins plugged to wall No 1 Remove toilet seat fixed to floor complete including cistern No 1 Steel urinal approximately 1000 x 1000mm high, Complete No 1 Taking down and removing roofs, floors, panelling, ceiling Gypsum plasterboard ceilings including cornices, timber brandering,etc m2 1 Take out and remove doors, windows, etc including thresholds. xxxxx, etc and prepare to receive new doors, frames, windows, etc. (all elswhere measured Timber single door, Door lockset including, handles, etc No 1 Taking out and removing glass and mirrors Panes exceeding 0,1m2 and not exceeding 0,5m2 (new glazing elsewhere measured) Item 1 Making good face brickwork Wash down existing face bricks wall with approved soap/acid and pressure hose Item 1 Carried to Final Summary MAINTENANCE OF FLUSHING TOILETS - SCHEDULE OF RATES Description Unit Quantity Rate Amount SECTION B BILL No.1 PLUMBING & DRAINAGE (PROVISIONAL) Class 200.00 180.00 220.00 750.00 ,500.00 50.00 36.00 11,200.00 9,180.00 3,300.00 4,500.00 15,000.00 2,400.00 9,216.00 1 Vitreous china WC pan with cistern No 56 2 Copper pipes 15Vitreous china wash hand basin No 51 3 Vitreous wall hung urinal No 15 4 Stainless steel slab urinal size 3000 x 1200mm pipe high including breaking up and fixing to walls etc including any necessary holderbats fixings etc m 1 28mm Ditto m 1 15mm Pipe chased into brickwork m 1 22mm Ditto m 1 28mm Ditto m 1 Extra Over copper pipes for brass compression fittings 15mm removing concrete urinal slab No 6 5 Showers No 10 6 Light fittings No 48 7 Ceilings m2 256 54,796.00 Carried Forward to Summary of Section No. 1 22mm Ditto R Amount Item No SECTION NO 1 28mm Ditto BILL NO 3 MASONRY NOTE: For Preambles see the Model Preambles for Trades 2008 edition published by the Association of South African Quantity Surveyors SUPPLEMENTARY PREAMBLES BRICKWORK Sizes in descriptions Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Face bricks Bricks shall be ordered timeously to obtain uniformity in size and colour Pointing Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc SUPERSTRUCTURE Brickwork of NFP bricks in class II (1:4) mortar Quantity 250.00 7,500.00 30 1 Half brick walls in vanity structure m2 7,500.00 Carried Forward to Summary of Section No. 1 SECTION 1 - BUILDING WORK MASONRY Rate Amount R Item No SECTION NO 1 50mm diameter uPVC pipes with solvent welded straight joints including all excavations not exceeding 1m deep m 1 Ditto but 110mm m 1 Extra Over uPVC pipes for 50mm straightb reducer solvent welded fittings No 1 Ditto but 50mm plain bend No 1 Ditto but 110mm plain bend No 1 Ditto 50mm access bend No 1 Ditto 50mm plain junction No 1 Ditto 110mm plain junction No 1 Ditto but 50mm access junction No 1BILL NO 4

REMOVAL OF EXISTING WORK. Hack up/off and remove ceramic tiles including removing mortar bed or adhesive from concrete or brickwork and preparing surface for new screed, plaster, tile finish, etc. Breaking up 100mm thick reinforced concrete thick m3 1 Breakdown 110mm brickwall m2 1 Ditto but to 220mm brickwall m2 1 Hack-up plaster work m2 1 Tiles to floors m2 1 Taking out and removing piping, sanitary fittings, etc including disconnecting piping from fittings and making good floor and wall finishes (making good tiling and paintwork elsewhere) Remove wash hand basins plugged to wall No 1 Remove toilet seat fixed to floor complete including cistern No 1 Steel urinal approximately 1000 x 1000mm high, Complete No 1 Taking down and removing roofs, floors, panelling, ceiling Gypsum plasterboard ceilings including cornicesceilings, timber brandering,etc m2 1 Take out and remove doors, windowspartitions, etc 1 Fascias and barge boards m 247 2 Xxxxx gutters including thresholds. xxxxx, etc and prepare to receive new doors, frames, windowsbrackets m 247 3 Downpipes including brackets, etc. (all elswhere measured Timber single doorm 32 4 Gypsum plasterboard ceilings, Door lockset includingincluding timber brandering, handlescornices, etc No 1 m2 174 Taking out and removing sundry joinery work, fittings, etc, 5 Gypsum coved cornices m 250 Taking out/off and removing glass and mirrors Panes exceeding 0,1m2 m2 120 Hacking up/off and not exceeding 0,5m2 (removing granolithic, screeds, plaster, etc from concrete or brickwork and preparing surfaces for new glazing elsewhere measured) Item 1 screed, plaster, tile finishes, etc 8 Internal plaster from walls and columns m2 660 Making good face brickwork Wash down 9 Faces of external walls by cleaning existing paint and repainting including the painting face bricks wall brick walls by applying brick dressing m2 444 Making good cement screeds 10 New screed on floors m2 488 Breaking up and removing reinforced concrete, including cutting off and removing reinforcement 11 Concrete apron slab m3 16 Carried Forward R Section No. 8 Bill No. 1 Refurbish 3 x 4 Classrooms (12 Classrooms) Independent Development Trust Tshembhani Primary School Provisional Bill of Quantities Brought Forward R NOTE : Tenderers are advised to study the "Specification of Materials and Methods to be used" (00G-001E) before pricing this bill Foundation brickwork and concrete walls have been measured to top of unfinished floor level BILL NO 2: CONCRETE, FORMWORK AND REINFORCEMENT NOTE : Tenderers are advised to study the "Specification of Materials and Methods to be used" (OOG-001E) before pricing this bill REINFORCEMENT Reinforced concrete with approved soap/acid a coarse aggregate of 19mm and pressure hose Item 1 Carried to Final Summary MAINTENANCE OF FLUSHING TOILETS - SCHEDULE OF RATES Description Unit Quantity Rate Amount SECTION B BILL No.1 PLUMBING & DRAINAGE (PROVISIONAL) Class 2 Copper pipes 15mm pipe and fixing to walls a minimum compressive strength of 20MPa at 28 days 12 In aprons slabs m3 32.00 Fabric reinforcement 13 Chicken mesh reinforcement in walls, etc including any necessary holderbats fixings etc m 1 28mm Ditto m 1 15mm Pipe chased into brickwork m 1 22mm Ditto m 1 28mm Ditto m 1 Extra Over copper pipes for brass compression fittings 15mm fittings No 1 22mm Ditto No 1 28mm Ditto No 1 50mm diameter uPVC pipes with solvent welded straight joints including all excavations not exceeding 1m deep m 1 Ditto but 110mm m 1 Extra Over uPVC pipes for 50mm straightb reducer solvent welded fittings No 1 Ditto but 50mm plain bend No 1 Ditto but 110mm plain bend No 1 Ditto 50mm access bend No 1 Ditto 50mm plain junction No 1 Ditto 110mm plain junction No 1 Ditto but 50mm access junction No 1m2 660.00 14 Type 395 fabric reinforcement in concrete surface beds, etc. m2 308.00

REMOVAL OF EXISTING WORK. Hack up/off Note: All alterations and remove ceramic tiles including removing mortar bed removal of existing work should be approved by the Architect before any work can be carried out by the appointed contractor or adhesive sub-contractor Old materials Old materials from concrete alterations except where described to be re- used or brickwork handed over, become the property of the Contractor Old materials from the alterations except where described to be re-used or handed over, as well as all rubbish etc. must be regularly carted from the site and preparing surface not be allowed to accumulate on or around the site None of the old materials are to be used for new screedwork except where specifically described as being set aside for re-use Where certain materials or articles from demolitions or alterations are described as to be handed over by the contractor to the Principal Agent such materials or articles shall be properly stored by the contractor, plasteruntil handing over thereof. The contractor shall obtain an official receipt listing the materials or articles and dates of handing over. If the contractor fails to submit the receipt when requested to do so it shall be deemed that the materials or articles are still in his possesion and he will be held liable to the Client for the full replacement value thereof which amount will be deducted from any monies due to the Contractor Credit for old materials Credit for old materials, tile finishif so desired, etc. is to be allowed for by the Contractor and a list of such credit items and rates will be included as part of the priced bills of quantities Client reserves the right to keep any or all of the old materials described in the bills of quantities irrespective of such materials having been listed and priced or not at the rates for the respective materials Breaking up 100mm thick and removing reinforced concrete thick m3 1 Breakdown 110Precast concrete benches size 2145 x 400mm brickwall wide No 2 - Breaking down and removing brickwork etc including making good adjacent wall and floor finishes 2 115mm brick wall m2 1 Ditto but to 22024 - 3 230mm brickwall brick wall m2 1 Hack-up plaster work m2 1 Tiles to floors m2 1 9 - Taking out and removing piping, sanitary fittings, etc including disconnecting piping from fittings and making good floor and wall finishes (making good tiling and paintwork elsewhere) Remove wash hand basins plugged to wall No 1 Remove toilet seat fixed to floor complete including cistern No 1 Steel urinal approximately 1000 x 1000mm high, Complete No 1 Taking down and removing roofs, floors, panelling, ceiling Gypsum plasterboard ceilings including cornices, timber brandering,etc m2 1 Take out and remove doors, windows, etc including thresholds. xxxxx, etc and prepare from brickwork to receive new doors, frames, windows, etc. (all elswhere measured be demolished Timber single door, Door lockset including, handles, etc No 1 door and steel frame size 813 x 2032mm high 7 Xxxxx gutters including down pipes m 65 - 8 Fascia and barge boards m 50 - Taking out and removing glass and mirrors Panes exceeding 0,1m2 and not exceeding 0,5m2 (new glazing elsewhere measured) Item 1 Making good face brickwork Wash down existing face bricks wall with approved soap/acid and pressure hose Item 1 Carried to Final Summary MAINTENANCE OF FLUSHING TOILETS - SCHEDULE OF RATES Description Unit Quantity Rate Amount SECTION B BILL No.1 PLUMBING & DRAINAGE (PROVISIONAL) Class 2 Copper pipes 15mm pipe and fixing to walls etc including any necessary holderbats fixings etc m 1 28mm Ditto m 1 15mm Pipe chased into sundry joinery work 9 Timber skirtings from brickwork m 1 22123 - Taking out and removing joinery fittings etc 10 600mm Ditto m 1 28mm Ditto m 1 Extra Over copper pipes for brass compression fittings 15mm fittings No 1 22mm Ditto No 1 28mm Ditto No 1 50mm diameter uPVC pipes with solvent welded straight joints Wide worktops including all excavations not exceeding 1m deep m 1 Ditto but 110mm m 1 Extra Over uPVC pipes for 50mm straightb reducer solvent welded fittings No 1 Ditto but 50mm plain bend No 1 Ditto but 110mm plain bend No 1 Ditto 50mm access bend No 1 Ditto 50mm plain junction No 1 Ditto 110mm plain junction No 1 Ditto but 50mm access junction No 1shelving, drawers, etc complete m2 7 - Taking out and removing ironmongery

REMOVAL OF EXISTING WORK. Hack up/Taking off and remove ceramic tiles including removing mortar bed or adhesive from concrete or brickwork and preparing surface for new screed, plaster, tile finish, etc. Breaking up 100mm thick reinforced concrete thick m3 1 Breakdown 110mm brickwall m2 1 Ditto but to 220mm brickwall m2 1 Hack-up plaster work m2 1 Tiles to floor coverings: A Remove existing timber boarded floors m2 1 (Provisional) m² 45 Taking out and removing pipingsundry joinery work, fittings, etc: B Timber skirtings from brickwork (Provisional) m 101 Remove existing sanitary fittings: C Remove existing stainless steel single bowl drop-in sink, etc including disconnecting piping from fittings and making good floor and wall finishes (making good tiling and paintwork elsewhere) taps, etc. complete, with approximate overall size: 2000 x 600mm wide No 1 D Remove existing water closet pans including cisterns, toilet seat, etc. complete No 5 E Remove existing wash hand basins plugged to wall basin including taps, etc. complete No 1 3 Take down IBR roof sheeting and cart off site: F Remove toilet seat fixed to floor complete including cistern No 1 Steel urinal approximately 1000 x 1000mm high, Complete No 1 Taking existing profiled roof covering and side cladding sheets. m² 85 Take down and removing roofsgutters including downpipes and cart off site: G Remove existing half-round asbestos gutters with approximate size: 150mm diameter fixed to fascia boards with and including clips, floorscomplete (Provisional) m 54 H Remove existing asbestos downpipes with approximate size: 150mm diameter with and including offsets, panellingshoes and brackets, ceiling Gypsum plasterboard ceilings including cornices, timber brandering,etc m2 1 complete (Provisional) m 31 Take out down and remove doors, windows, etc including thresholds. xxxxx, etc fascia and prepare barge boards: I Remove existing fibre cement fascia and barge boards with approximate size: 12 x 350mm wide fixed to receive new doors, frames, windowstimber rafters, etc. (Provisional) m 120 Carried Forward R SECTION NO. 2 BILL NO. 01 - ALTERATIONS Brought Forward R CLEAN DOWN SURFACES Clean asbestos and fibre cement roofs by means of high pressure water jet including pitches not exceeding 25 degrees, valleys, hips, xxxxx ends etc, thoroughly cleaning and brushing down of all elswhere measured Timber dirt, scale and general surface contamination, locating leaks and making watertight, refixing loose screws, replacing damaged or missing screws, etc. and leave perfectly clean on completion in preparation to receive new paint (new paint elsewhere measured) (contractor to follow precautionary guidelines as per Occupational Health & Safety Act): A Waterjet profiled asbestos roof covering with pitch not exceeding 25 degrees m² 583 B Waterjet profiled fibre cement roof covering with pitch not exceeding 25 degrees m² 450 SERVICING OF WINDOWS, DOORS, PLUMBING, ETC. Attend to, service, re-align and repair as necessary all steel windows including removing existing putty, applying new putty and replacing any defective or missing parts: C Service existing steel windows, including burglar bars, with overall size: 957 x 1814mm high (B319: Window type W4) No 2 D Service existing steel windows, including burglar bars, with overall size: 900 x 480mm high (B321: Window type W1) No 2 E Service existing steel windows, including burglar bars, with overall size: 470 x 880mm high (B321: Window type W2) No 3 F Service existing steel windows, including burglar bars, with overall size: 1435 x 625mm high (B322: Window type W1) No 17 Carried Forward R SECTION NO. 2 BILL NO. 01 - ALTERATIONS Brought Forward R Attend to, service, re-align and repair as necessary all timber windows including removing existing putty, applying new putty and replacing any defective or missing parts: A Service existing timber windows, including burglar bars, with overall size: 1070 x 2064mm high (B319: Window type W1). No 14 B Service existing timber windows, including burglar bars, with overall size: 2116 x 2064mm high (B319: Window type W2) No 4 C Service existing timber windows, including burglar bars, with overall size: 2189 x 988mm high (B319: Window type W3) No 1 D Service existing timber windows, including burglar bars, with overall size: 600 x 600mm high (B323: Window type W1) No 4 E Service existing timber windows, including burglar bars, with overall size: 1465 x 1200mm high (B324: Window type W1) No 15 Attend to, service and repair as necessary all timber doors including replacing any defective or missing parts: F Service existing timber single door, glass pane including fanlight, with overall size: 936 x 2732mm high including hinges and ensure that door is properly aligned to open and close correctly (B319: Door lockset including, handles, etc type D1) No 1 Taking out G Service existing timber double door, glass panelled including fanlight, with approximate overall size: 1690 x 2732mm high including hinges and removing glass ensure that door is properly aligned to open and mirrors Panes exceeding 0,1m2 close correctly (B319: Door type D2) No 2 H Service existing timber single door, including fanlight, with overall size: 848 x 2627mm high including hinges and not exceeding 0,5m2 ensure that door is properly aligned to open and close correctly (new glazing elsewhere measuredB319: Door type D3) Item No 1 Making good face brickwork Wash down I Service existing face bricks wall timber single door, including fanlight, with approved soap/acid overall size: 936 x 2818mm high including hinges and pressure hose Item ensure that door is properly aligned to open and close correctly (B319: Door type D4) No 1 Carried Forward R SECTION NO. 2 BILL NO. 01 - ALTERATIONS Brought Forward R A Service existing timber single door with overall size: 835 x 2022mm high including hinges and ensure that door is properly aligned to Final Summary MAINTENANCE OF FLUSHING TOILETS - SCHEDULE OF RATES Description Unit Quantity Rate Amount SECTION open and close correctly (B319: Door type D6) No 6 B BILL No.1 PLUMBING & DRAINAGE Service existing timber single sliding door with overall size: 999 x 2127mm high including hinges and ensure that door is properly aligned to open and close correctly (PROVISIONALB319: Door type D7) Class 2 Copper pipes 15mm pipe and fixing to walls etc including any necessary holderbats fixings etc m 1 28mm Ditto m 1 15mm Pipe chased into brickwork m 1 22mm Ditto m 1 28mm Ditto m 1 Extra Over copper pipes for brass compression fittings 15mm fittings No 1 22C Service existing timber double door with overall size: 1622 x 2100mm Ditto high including hinges and ensure that door is properly aligned to open and close correctly (B324: Door type D2) No 1 28D Service existing timber single door with overall size: 737 x 2015mm Ditto high including hinges and ensure that door is properly aligned to open and close correctly (B321: Door type D1) No 2 E Service existing timber single door with overall size: 737 x 2015mm high including hinges and ensure that door is properly aligned to open and close correctly (B321: Door type D1) No 3 F Service existing timber single door with overall size: 900 x 2100mm high including hinges and ensure that door is properly aligned to open and close correctly (B322, B322 & B324: Door type D1) No 6 G Service existing timber single door with overall size: 900 x 2100mm high including hinges and ensure that door is properly aligned to open and close correctly (B323: Door type D2) No 2 H Service existing timber single door, including fanlight, with overall size: 935 x 2649mm high including hinges and ensure that door is properly aligned to open and close correctly (B319: Door type D5) No 1 50mm diameter uPVC pipes with solvent welded straight joints including all excavations not exceeding 1m deep m 1 Ditto but 110mm m 1 Extra Over uPVC pipes for 50mm straightb reducer solvent welded fittings No 1 Ditto but 50mm plain bend No 1 Ditto but 110mm plain bend No 1 Ditto 50mm access bend No 1 Ditto 50mm plain junction No 1 Ditto 110mm plain junction No 1 Ditto but 50mm access junction No 1Carried Forward to Summary of Section No. R SECTION NO. 2 BILL NO. 01 - ALTERATIONS

REMOVAL OF EXISTING WORK. Hack up/off Note: Unless otherwise stated, all materials from the alterations and remove ceramic tiles including demolitions will belong to the builder. The builder should allow for the removal of all debris from site and keep the site clean at all times Removal of exsiting concrete 1 Surface beds m3 48 Breaking down and removing mortar bed or adhesive from concrete or brickwork and preparing surface for new screed, plaster, tile finish, etc. Breaking up 100mm thick reinforced concrete thick m3 1 Breakdown 110mm brickwall etc 2 Half brick wall m2 1 Ditto but to 220mm brickwall 50 3 Xxxxx wall m2 1 Hack-up plaster work m2 1 Tiles to floors m2 1 18 Taking out and removing pipingdoors, sanitary fittingswindows, etc including disconnecting piping from fittings 4 Timber single door and making good floor steel door frame, size 813 x 2032mm high No 7 5 Timber single door and wall finishes (making good tiling and paintwork elsewhere) Remove wash hand basins plugged to wall steel door frame, size 1626 x 2032mm high No 1 Remove toilet seat fixed to floor complete including cistern No 1 Steel urinal approximately 1000 x 1000mm high, Complete No 1 3 Taking down and removing roofs, floors, panelling, ceiling Gypsum plasterboard ceilings, partitions, etc 6 Corrugated iron roof including roof covering, timber trusses and purlins, ceilings including and cornices, timber brandering,etc xxxxx soffit covering, fascias, barge boards, gutters and rainwater pipes m2 1 Take out and remove doors, windows, etc including thresholds. xxxxx, etc and prepare 594 Carried to receive new doors, frames, windows, etc. (all elswhere measured Timber single door, Door lockset including, handles, etc No 1 Collection R Amount Taking out and removing removal glass and mirrors Panes 7 Glass from steel window including cleaning out rebates and preparing for new glass m2 64 Hacking up/off and removing granolithic , screed , plaster . ect from concrete or brickwork and preparing surface fpr new screed plaster 8 Internal plaster m2 583 9 External plaster CONCRETE, FORMWORK AND REINFORCEMENT m2 357 SUPPLEMENTARY PREAMBLES Cost of tests The costs of making, storing and testing of concrete test cubes as required under clause 7 "Tests" of SABS 1200 G shall include the cost of providing cube moulds necessary for the purpose, for testing costs and for submitting reports on the tests to the architect. The testing shall be undertaken by an independent firm or institution nominated by the contractor and to the approval of the architect. (Test cubes are measured separately) Breeze concrete Breeze concrete shall consist of twelve parts clean dry furnace ash, free from coal or other foreign matter, to one part cement (12:1), the ash graded up to particles which will pass a 16,5mm ring from a minimum which fails to pass a 4,75mm mesh. The finer materials from the screening are to be first mixed with the cement into a mortar and the ash added afterwards and thoroughly incorporated Formwork Description of formwork shall be deemed to include use and waste only (except where described as "left in" or "permanent"), for fitting together in the required forms, wedging, plumbing and fixing to true angles and surfaces as necessary to ensure easy release during stripping and for reconditioning as necessary before re- use Carried to Collection R The vertical strutting shall be carried down to such construction as is sufficiently strong to afford the required support without damage and shall remain in position until the newly constructed work is able to support itself Formworks to soffits of solid slabs etc shall be deemed to be slabs not exceeding 0,1m2 250mm thick unless otherwise described Formwork to soffits of slabs, beams, etc shall be deemed to be propped up exceeding 1,5m and not exceeding 0,5m2 (new glazing elsewhere measured) Item 1 Making good face brickwork Wash down existing face bricks wall with approved soap/acid 3,5m high unless otherwise described Formwork to sides of bases, pile caps, ground beams, etc will only be measured where it is prescribed by the engineer for design reasons. Formwork necessitated by irregularity or collapse of excavated faces will not be measured and pressure hose Item 1 Carried the cost thereof shall be deemed to Final Summary MAINTENANCE OF FLUSHING TOILETS - SCHEDULE OF RATES Description Unit Quantity Rate Amount SECTION B BILL No.1 PLUMBING & DRAINAGE (PROVISIONAL) Class 2 Copper pipes 15mm pipe and fixing to walls etc including any necessary holderbats fixings etc m 1 28mm Ditto m 1 15mm Pipe chased into brickwork m 1 22mm Ditto m 1 28mm Ditto m 1 Extra Over copper pipes be included in the allowance for brass compression fittings 15mm fittings No 1 22mm Ditto No 1 28mm Ditto No 1 50mm diameter uPVC pipes with solvent welded straight joints including all excavations not exceeding 1m deep m 1 Ditto but 110mm m 1 Extra Over uPVC pipes taking the risk of collapse of the sides of the excavations, provision for 50mm straightb reducer solvent welded fittings No 1 Ditto but 50mm plain bend No 1 Ditto but 110mm plain bend No 1 Ditto 50mm access bend No 1 Ditto 50mm plain junction No 1 Ditto 110mm plain junction No 1 Ditto but 50mm access junction No 1which is made in "Earthworks"