Common use of Power Reduction Clause in Contracts

Power Reduction. 19.5.1 The Collocator may request to decrease the amount of existing power available to a Collocation Arrangement. This can be done either by disconnecting and removing a power cable feed or by replacing the existing fuse with a fuse of a lower breakdown rating on a power cable feed. If the Collocator desires to disconnect a power arrangement (A&B feed), the Collocator will be responsible for hiring an AT&T- 21STATE AIS Tier 1 to remove the terminations at both ends of the power cable feed and cut cables up to the AT&T-21STATE rack level that make up the power arrangement. If the Collocator desires to reduce the amperage on a power cable feed, the Collocator will be responsible for paying the costs necessary to change the fuse that serves the A&B feeds at the AT&T-21STATE power source. In either case, the Collocator must maintain a minimum amount of power on at least one power arrangement (A&B feed) to service their Collocation Arrangement when submitting their power reduction request. The Collocator shall submit an augment application in order to process this request. 19.5.2 If the Collocator desires to only reduce the fuse capacity on an existing power arrangement (A&B feed) rather than disconnect and remove cable to an existing power arrangement, they may only reduce the fuse size to the lowest power amp increment offered in this Attachment referenced in 19.2 above. Different minimum amp increments apply for power arrangements fed from either an AT&T-21STATE BDFB or an AT&T-21STATE power plant. When the Collocator is requesting to reduce the fuse capacity only, the fees referenced in the Pricing Schedule will apply. When the Collocator has only one power arrangement (A&B feed) serving their Collocation Arrangement, a fuse reduction is the only power reduction option available to the Collocator. 19.5.3 When a power reduction request involves a fuse change only on a power arrangement serviced from the AT&T-21STATE BDFB (e.g., power arrangements less than or equal to a fifty (50) amp A feed and a fifty (50) amp B feed) the Collocator must hire an AT&T-21STATE AIS Tier 1 to coordinate fuse changes at the AT&T-21STATE BDFB. Applicable fees referenced in Pricing Schedule will still apply. When a power reduction request involves a fuse change on a power arrangement serviced from the AT&T-21STATE Power Plant (e.g., power arrangements consisting of a one hundred (100) amp A feed and a one hundred (100) amp B feed and above), the Collocator must hire an AT&T-21STATE AIS Tier 1 power supplier to coordinate the fuse changes at the AT&T-21STATE power plant. 19.5.4 When a power reduction request requires disconnecting and removing a power cable feed from either the AT&T-21STATE’s BDFB (Battery Distribution Fuse Bay) or power plant, the AT&T-21STATE AIS Tier 1 will perform the power cable removal work up to the rack level. Applicable fees referenced in Pricing Schedule will apply. Within thirty (30) calendar days after submitting its power reduction request to disconnect and remove a power arrangement, the Collocator must perform the following activity:

Power Reduction. 19.5.1 19.4.1 The Wireless Collocator may request to decrease the amount of existing power available to a Physical Collocation Arrangement. This can be done either by disconnecting and removing a power cable feed or by replacing the existing fuse with a fuse of a lower breakdown rating on a power cable feed. If the Wireless Collocator desires to disconnect a power arrangement (A&B feed), the Wireless Collocator will be responsible for hiring an AT&T- 21STATE AIS Tier 1 paying the costs to remove the terminations at both ends of the A&B power cable feed and cut cables up to the AT&T-21STATE rack level feeds that make up the power arrangement. If the Wireless Collocator desires to reduce the amperage on a power cable feed, the Wireless Collocator will be responsible for paying the costs necessary to change the fuse that serves the A&B feeds at the AT&T-21STATE AT&T-13STATE power source. In either case, the Wireless Collocator must maintain a minimum amount of power on at least one power arrangement (A&B feed) to service their Physical Collocation Arrangement when submitting their power reduction request. The Wireless Collocator shall submit an augment application in order to process this request. 19.5.2 19.4.2 If the Wireless Collocator desires to only reduce the fuse capacity on an existing power arrangement (A&B feed) rather than disconnect and remove cable to an existing power arrangement, they may only reduce the fuse size to the lowest power amp increment offered in this Attachment Appendix referenced in 19.2 aboveSection 18.3. 3.1. Different minimum amp increments apply for power arrangements fed from either an AT&T-21STATE BDFB AT&T-13STATE Battery Distribution Fuse Bay (BDFB) or an AT&T-21STATE power plantAT&T-13STATE Power Plant. When the Wireless Collocator is requesting to reduce the fuse capacity only, the fees referenced in the Pricing Schedule Section 19.9 will apply. When the Wireless Collocator has only one power arrangement (A&B feed) serving their Physical Collocation Arrangement, a fuse reduction is the only power reduction option available to the Wireless Collocator. 19.5.3 19.4.3 When a power reduction request involves a fuse change only on a power arrangement serviced from the AT&T-21STATE AT&T-13STATE BDFB (e.g., i.e. power arrangements less than or equal to a fifty (50) amp A feed and a fifty (50) amp B feed) the Wireless Collocator must hire an AT&T-21STATE AIS AT&T-13STATE Approved Tier 1 Vendor to coordinate fuse changes at the AT&T-21STATE AT&T-13STATE BDFB. Applicable fees referenced in Pricing Schedule Section 19.9 will still apply. When a power reduction request involves a fuse change on a power arrangement serviced from the AT&T-21STATE AT&T-13STATE Power Plant (e.g., power arrangements consisting of a one hundred (100) amp A feed and a one hundred (100) amp B feed and above), the Collocator must hire an AT&T-21STATE AIS Tier 1 power supplier to coordinate the fuse changes at the AT&T-21STATE power plant. 19.5.4 When a power reduction request requires disconnecting and removing a power cable feed from either the AT&T-21STATE’s BDFB (Battery Distribution Fuse Bay) or power plant, the AT&T-21STATE AIS Tier 1 will perform the power cable removal work up to the rack level. Applicable fees referenced in Pricing Schedule will apply. Within thirty (30) calendar days after submitting its power reduction request to disconnect and remove a power arrangement, the Collocator must perform the following activity:i.

Power Reduction. 19.5.1 The Collocator may request to decrease the amount of existing power available to a Collocation Arrangement. This can be done either by disconnecting and removing a power cable feed or by replacing the existing fuse with a fuse of a lower breakdown rating on a power cable feed. If the Collocator desires to disconnect a power arrangement (A&B feed), the Collocator will be responsible for hiring an AT&T- 21STATE AT&T-21STATE AIS Tier 1 to remove the terminations at both ends of the power cable feed and cut cables up to the AT&T-21STATE rack level that make up the power arrangement. If the Collocator desires to reduce the amperage on a power cable feed, the Collocator will be responsible for paying the costs necessary to change the fuse that serves the A&B feeds at the AT&T-21STATE power source. In either case, the Collocator must maintain a minimum amount of power on at least one power arrangement (A&B feed) to service their Collocation Arrangement when submitting their power reduction request. The Collocator shall submit an augment application in order to process this request. 19.5.2 If the Collocator desires to only reduce the fuse capacity on an existing power arrangement (A&B feed) rather than disconnect and remove cable to an existing power arrangement, they may only reduce the fuse size to the lowest power amp increment offered in this Attachment referenced in 19.2 above. Different minimum amp increments apply for power arrangements fed from either an AT&T-21STATE BDFB or an AT&T-21STATE power plant. When the Collocator is requesting to reduce the fuse capacity only, the fees referenced in the Pricing Schedule will apply. When the Collocator has only one power arrangement (A&B feed) serving their Collocation Arrangement, a fuse reduction is the only power reduction option available to the Collocator. 19.5.3 When a power reduction request involves a fuse change only on a power arrangement serviced from the AT&T-21STATE BDFB (e.g., power arrangements less than or equal to a fifty (50) amp A feed and a fifty (50) amp B feed) the Collocator must hire an AT&T-21STATE AIS Tier 1 to coordinate fuse changes at the AT&T-21STATE AT&T- 21STATE BDFB. Applicable fees referenced in Pricing Schedule will still apply. When a power reduction request involves a fuse change on a power arrangement serviced from the AT&T-21STATE Power Plant (e.g., power arrangements consisting of a one hundred (100) amp A feed and a one hundred (100) amp B feed and above), the Collocator must hire an AT&T-21STATE AIS Tier 1 power supplier to coordinate the fuse changes at the AT&T-21STATE power plant. 19.5.4 When a power reduction request requires disconnecting and removing a power cable feed from either the AT&T-21STATE’s BDFB (Battery Distribution Fuse Bay) or power plant, the AT&T-21STATE AIS Tier 1 will perform the power cable removal work up to the rack level. Applicable fees referenced in Pricing Schedule will apply. Within thirty (30) calendar days after submitting its power reduction request to disconnect and remove a power arrangement, the Collocator must perform the following activity: 19.5.4.1 Remove terminations at both ends of the power cable feed and cut cables up to the AT&T- 21STATE rack level. Collocator must use an AT&T-21STATE AIS Tier 1 for this procedure and that supplier must follow TP76300 guidelines for cutting and capping the cable at the rack level.