MECHANICAL COMPONENTS Sample Clauses

MECHANICAL COMPONENTS. A corrosion resistant metallic frame structure should be fixed on the pole to hold the SPV module.
AutoNDA by SimpleDocs
MECHANICAL COMPONENTS. Office Floors 3-7, 13-15
MECHANICAL COMPONENTS. 6.15.1 Metallic frame structure of galvanized steel with stands to be fixed on the roof/terrace to hold the SPV module (s) above roof level and clearance between roof/terrace level and PV module shall be kept as per relevant IEC/BIS norms. Concrete foundations of appropriate weight and depth for elevated structures mounted directly on the roof/terrace; bolted with anchor bolts of appropriate strength for elevated structures mounted on RCC foundation. 6.15.2 Civil Foundation for Solar PV Module Mounting Structure (MMS): The foundations shall be designed considering the weight and distribution of the structure and assembly, and a maximum wind speed. Seismic factors for the site to be considered while making the foundation design. Foundations shall be made in accordance with the Indian Standard Codes, with the help of Registered Structural Designer having substantial experience in similar work. Bidder shall submit the detailed structural design analysis along with calculations and bases / standards. 6.15.3 Successful bidder shall design and construct appropriate civil foundations for MMS, prefabricated structures, etc. The design of RCC foundation shall be approved by RMC. 6.15.4 The frame structure should have provision to adjust at necessary angle of inclination to the horizontal, so that it can be installed at the specified tilt angle i.e. inclined at necessary degree to horizontal facing to south. All hardware, nuts, bolts should be SS - 304.
MECHANICAL COMPONENTS. (a) Metallic frame structure(with corrosion resistance paint) to be fixed on the roof of the house to hold the SPV module(s). The frame structure should have provision to adjust its angle of inclination to the horizontal between 0 and 45, so that it can be installed at the specified tilt angle. (b) A vented metallic box with acid proof and corrosion resistance paint .for housing the storage battery indoors should be provided. The box can be of injection moulded polymer.
MECHANICAL COMPONENTS. Inspect curtain conditions (level, alignment and operation) - Adjust spring tension - Check endlocks for wear or damage - Check guides for damage and mounting to jambs - Check all sprockets for proper alignment and tightness as well as tooth wear - Check tension on drive chain - Oil or grease all bearings, guides, and moving parts as required Electric Operator (if applicable): Inspect, Adjust & Lubricate the following: - Clutch - Limit switch - Brake and brake solenoid - Bearings - Chains - Gear reducers - Bearings - Chains - Sprockets - Belts - Safety Devices
MECHANICAL COMPONENTS. Wheelchair locking mechanism, power seat base, hand/driving controls.
MECHANICAL COMPONENTS. KA Gate valves, cocks, valves, taps, bursting disks, throttling orifices, end plates KB Gates, doors, partition xxxxx XX Heat exchangers, coolers KD Reservoirs, vessels, level (process) vessels KE Turning, handling, hoisting and rotating mechanisms KF Conveyers, feeders KJ Crushing machines KK Pressing and stacking machines KM Mixers KN Compressors, air blowers, fans KP Pumps KT Cleaning machines, dryers, separators, filters KV Burners, fire bars KW Stationary machines and processing machines for maintenance MB Brakes MF Foundations MG Reducing gears MK Clutches MM Engines (non-electric) MR Piping parts, parts of technical channels, sockets MS Drives, non-electric MT Turbines MU Transmission components, non-electric converters and amplifiers, except for clutches and reducing gears QB Measurement sensors if not structurally integral with *QP* QH Signalling devices QN Controllers, centrifugal governors QP Measurement instruments, testing equipment QR Instrument piping QS Level vessels in measurement circuits QT Protecting tubes and sleeves for protection of vulnerable sensors
AutoNDA by SimpleDocs
MECHANICAL COMPONENTS. A mechanical component refers to a component that has some kind of mechanism, such as a linkage or a bearing-supported shaft.
MECHANICAL COMPONENTS. 1.1 Check all mechanical control valves, seats and discs, spindles and springs replaced if necessary. 1.2 Examine all unions, pipes, connections and fittings for leaks and tightness. Repair where necessary. 1.3 Open and clean out all strainers. 1.4 Check all steam traps, clean out and replace if necessary. 1.5 Check glands on vacuum pumps, re-pack if necessary. 1.6 Check all reducing valves for accuracy, adjust if necessary. 1.7 Examine water tank for corrosion, replace if necessary. 1.8 Check conditions of all "V" belts and pulleys, adjust or replace if necessary. 1.9 Clean and lubricate all mechanical moving parts on machine. 1.10 Replace bacteria air filter and sock and replace if necessary. 1.11 Test all non-return valves and replace if necessary. 1.12 Check all safety valves for correct operation, adjust or replace if necessary. 1.13 Check chamber visually for cracks.
MECHANICAL COMPONENTS. (i) Corrosion resistant metallic frame structure should be provided to hold the SPV module. (ii) The frame structure should have provision to adjust its angle of inclination to the horizontal, so that it can be installed at the specified tilt angle. (iii) Light source should be either for wall mounted or ceiling mounted or can be hung from the ceiling in a stable manner, as per site requirements. (iv) A vented plastic/ wooden/ metallic box with acid proof corrosion resistant paint for housing the storage battery indoors should be provided.
Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!