Gauge Sample Clauses

Gauge. (Circle as Applicable) (a) 35mm (b) 16mm
AutoNDA by SimpleDocs
Gauge. The Network shall be capable of accommodating Registered Equipment of up to W6 gauge throughout. Any Services conveying ‰ as specified in Annex I to this Schedule 2, which exceed W6 gauge shall not be constrained by the provisions of this paragraph 1.7. With the exception of the conveyance of ‰ as specified in Annex I to this Schedule 2, EWS shall not knowingly cause or permit Services on the Network to exceed W6 gauge unless it shall have obtained WR plc’s prior written consent such consent not to be unreasonably withheld.
Gauge. Rear side top Takasivu ylhäällä Rear side Takasivulla Bottom Alhaalla Operating side KäyttösivulIa Operating side top Käyttösivu ylhäällä Deviations 1/100 mm COLD ENGINE Measurements of crankshaft alignment made in main assembly Room temperature when values were measured [°C]: 21 °C Initials: PK Cylinder Guage Rear side top Takasivu ylhäällä Rear side Takasivulla Bottom Alhaalla Operating side Käyöttdsivulla Operating side top Käyttösivu ylhäällä Deviations 1/100 mm Test xxxxxxxx xx XXXX000000 Report RA_061.QRP Version: 3.0.0.2 Printed 09.01.2009 Delivery Centre Vaasa Inspection of the Wärtsilä Engine Project: Order number: Engine type: Engine number: Classification society: Test run date(s) Inspection date: It has been agreed that the following openings and inspections are to be carried out at the delivery test run attended by the buyer and / or the representative of the classification society. Inspections: Results: Big end bearing No. B4 OK Main bearing No. 7 OK Thrust bearing Yes OK Opening of covers Yes OK Additional information: The following corrections should be made before delivery: WÄRTSILÄ Finland Oy Customer(s) Wärtsilä Finland Oy Vaasa Factory W 32 [ILLEGIBLE] Test Run Manager, Delivery Centre Vaasa Third Party Inspection [ILLEGIBLE] Test protocol no PAAE138971 Report RA_062.QRP Version: 3.0.0.3 Printed 09.01.2009 Delivery Centre Vaasa Fuel Oil Consumption According to ISO 15550 Engine number: Project: Order number: Engine type: W20V32 Output/100% [kW]: Speed [rpm]: Test run date(s): K = ratio of indicated power s = 1 exponent
Gauge. The Network shall be capable of accommodating Registered Equipment of up to W6A (W6) gauge throughout. CRL shall not knowingly cause or permit Services on the Network to exceed W6A (W6) gauge unless it shall have obtained RRL‟s prior written consent such consent not to be unreasonably withheld.

Related to Gauge

  • Speed The relative importance we attach is “high”.

  • Temperature Where low temperature and/or self-service cases are used for any of such merchandise coming under the jurisdiction of the Union, such cases shall be served only by employees covered by this Agreement.

  • Metering The Interconnection Customer shall be responsible for the Connecting Transmission Owner’s reasonable and necessary cost for the purchase, installation, operation, maintenance, testing, repair, and replacement of metering and data acquisition equipment specified in Attachments 2 and 3 of this Agreement. The Interconnection Customer’s metering (and data acquisition, as required) equipment shall conform to applicable industry rules and Operating Requirements.

  • NIGHTLY a. All floors in Group A to be swept, wet mopped and rinsed.

  • Electrical Provide drawings for the following systems:

  • Weights light, moderate and heavy, have their normal everyday meanings, and are to be applied consistently, regardless of the physical characteristics of the jobholder and whether the duties are normally carried out by women or by men; or by small people or large people; or by fit or unfit people. So, a sack of cement or a sack of potatoes is a heavy weight, even if it is lifted and carried without obvious exertion by a tall, fit, young person.

  • Delivery Pressure Xxxxxx agrees to use due care and diligence to furnish gas hereunder at such uniform pressure as Seller may elect up to, but not exceeding 20 pounds per square inch gauge, and not less than 5 pounds per square inch gauge, at the "Point of Delivery". Buyer shall be responsible for the installation and operation of adequate safety equipment downstream of the Point of Delivery so as to relieve or control pressure variations within the limits described above that may, for any reason through malfunction of Seller's equipment or otherwise, occur on Buyer's side of the "Delivery Point".

  • Compatibility 1. Any unresolved issue arising from a mutual agreement procedure case otherwise within the scope of the arbitration process provided for in this Article and Articles 25A to 25G shall not be submitted to arbitration if the issue falls within the scope of a case with respect to which an arbitration panel or similar body has previously been set up in accordance with a bilateral or multilateral convention that provides for mandatory binding arbitration of unresolved issues arising from a mutual agreement procedure case.

  • Delivery Points ‌ Project water made available to the Agency pursuant to Article 6 shall be delivered to the Agency by the State at the delivery structures established in accordance with Article 10.

  • Loading RPMG shall schedule the loading and shipping of all outbound corn oil purchased hereunder, but all labor and equipment necessary to load trucks and rail cars and other associated costs shall be supplied and borne by Producer without charge to RPMG. Producer shall handle the corn oil in a good and workmanlike manner in accordance with RPMG’s written requirements and normal industry practice. Producer shall maintain the truck and rail loading facilities in safe operating condition in accordance with normal industry standards and shall visually inspect all trucks and rail cars to assure (i) cleanliness so as to avoid contamination, and (ii) that such trucks and railcars are in a condition suitable for transporting the corn oil. RPMG and RPMG’s agents shall have adequate access to the Ethanol Facility to load Producer’s corn oil on an industry standard basis that allows RPMG to economically market Producer’s corn oil. RPMG’s employees shall follow all reasonable safety rules and procedures promulgated by Producer and provided to RPMG reasonably in advance and in writing. Producer shall supply product description tags, certificates of analysis, bills of lading and/or material safety data sheets that are applicable to all shipments. In the event that Producer fails to provide the labor, equipment and facilities necessary to meet RPMG’s loading schedule, Producer shall be responsible for all costs and expenses, including without limitation actual demurrage and wait time, incurred by RPMG resulting from or arising in connection with Producer’s failure to do so.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!