Common use of First sampling Clause in Contracts

First sampling. In the first sampling four rear marking plates are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates shall not be contested if the deviation of the measured values of the rear marking plates in the unfavourable directions are: 2.1.1.1. sample A A1: one rear marking plate 0 per cent one rear marking plate not more than 20 per cent A2: both rear marking plates more than 0 per cent but not more than 20 per cent go to sample B 2.1.1.2. sample B 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates are: 2.2.1.1. sample A A3: one rear marking plate not more than 20 per cent one rear marking plate more than 20 per cent but not more than 30 per cent 2.2.1.2. sample B B2: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 20 per cent but not more than 30 per cent 2.3. Approval withdrawn 2.3.1. sample A A4: one rear marking plate not more than 20 per cent one rear marking plate more than 30 per cent A5: both rear marking plates more than 20 per cent 2.3.2. sample B B4: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate more than 20 per cent B5: in the case of A2 both rear marking plates more than 20 per cent B6: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 30 per cent

First sampling. In the first sampling four rear marking plates are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in Figure figure 1 of this annex the conformity of mass-mass- produced rear marking plates shall not be contested if the deviation of the measured values of the rear marking plates in the unfavourable directions are: 2.1.1.1. sample A A1: one rear marking plate 0 per cent one rear marking plate not more than 0 per cent 20 per cent A2: both rear marking plates more than 0 per cent but not more than 20 per cent go to sample B 0 per cent 20 per cent 2.1.1.2. sample B 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in Figure figure 1 of this annex the conformity of mass-mass- produced rear marking plates shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates are: 2.2.1.1. sample A A3: one rear marking plate not more than 20 per cent one rear marking plate more than 20 per cent but not more than 30 per cent 2.2.1.2. sample B B2: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate not more than 0 per cent 20 per cent 20 per cent B3: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 20 per cent but not more than 20 per cent 30 per cent 2.3. Approval withdrawn 2.3.1. sample A A4: one rear marking plate not more than 20 per cent one rear marking plate more than 30 per cent A5: both rear marking plates more than 20 0 per centcent E/ECE/TRANS/505 Regulation No. 70 page 38 Annex 14 2.3.2. sample B B4: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate more than 0 per cent 20 per cent 20 per cent B5: in the case of A2 both rear marking plates more than 20 per cent B6: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 30 per cent

First sampling. In the first sampling four rear marking plates are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in Figure figure 1 of this annex the conformity of mass-mass- produced rear marking plates shall not be contested if the deviation of the measured values of the rear marking plates in the unfavourable directions are: 2.1.1.1. sample A A1: one rear marking plate 0 per cent one rear marking plate not more than 0 per cent 20 per cent A2: both rear marking plates more than 0 per cent but not more than 20 per cent go to sample B 0 per cent 20 per cent 2.1.1.2. sample B 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in Figure figure 1 of this annex the conformity of mass-mass- produced rear marking plates shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates are: 2.2.1.1. sample A A3: one rear marking plate not more than 20 per cent one rear marking plate more than 20 per cent but not more than 30 per cent 2.2.1.2. sample B B2: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate not more than 20 per cent 20 per cent B3: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 20 per cent but not more than 20 per cent 30 per cent 2.3. Approval withdrawn 2.3.1. sample A A4: one rear marking plate not more than 20 per cent one rear marking plate more than 30 per cent A5: both rear marking plates more than 20 0 per centcent E/ECE/TRANS/505 Regulation No. 70 page 38 Annex 14 2.3.2. sample B B4: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate more than 20 per cent 20 per cent B5: in the case of A2 both rear marking plates more than 20 per cent B6: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 30 per cent

First sampling. In the first sampling four rear marking plates are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates shall not be contested if the deviation of the measured values of the rear marking plates in the unfavourable directions are: 2.1.1.1. sample A A1: one rear marking plate 0 per cent one rear marking plate not more than 20 per cent A2: both rear marking plates more than 0 per cent but not more than 20 per cent go to sample B 20 per cent 2.1.1.2. sample BB B1: both rear marking plates 0 per cent 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates are: 2.2.1.1. sample A A3: one rear marking plate not more than 20 per cent one rear marking plate more than 20 per cent but not more than 30 per cent 2.2.1.2. sample B B2: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 20 per cent but not more than 30 per cent 2.3. Approval withdrawnwithdrawn Conformity shall be contested and paragraph 10 applied if, following the sampling procedure in Figure 1 of this annex, the deviations of the measured values of the rear marking plates are: 2.3.1. sample A A4: one rear marking plate not more than 20 per cent one rear marking plate more than 30 per cent A5: both rear marking plates more than 20 0 per cent 2.3.2. sample B B4: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate more than 20 per cent B5: in the case of A2 both rear marking plates more than 20 per cent B6: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 30 per cent