Common use of First sampling Clause in Contracts

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go to sample B 2.1.1.2. Sample B B1: both headlamps 0 per cent 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are: 2.3.1. Sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. Sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample A A1: one headlamp 0 per cent one headlamp not more than 0 per cent 20 per cent A2: both headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent Go to sample B cent 2.1.1.2. Sample B B1: both headlamps 0 per cent 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.22.1.2. Sample B B2: in the case of A2 one headlamp but one headlamp more than not more than not more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp but more than not more than 20 per cent but not more than 30 per centcent Annex 7 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are: 2.3.1. Sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. Sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per centA2

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested: 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample A A1: one One headlamp 0 per cent one One headlamp not more than 20 per cent A2: both Both headlamps more than 0 per cent but But not more than 20 per cent Go to sample B 2.1.1.2. Sample B B1: both Both headlamps 0 per cent 2.1.2. Or if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested: 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample A : A3: one One headlamp not more than One headlamp more than But not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. cent Sample B B2: in In the case of A2 one One headlamp more than But not more than One headlamp not more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in In the case of A2 one One headlamp One headlamp more than But not more than 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.1. Sample A 2.2.1.2. 2.2.2. Or if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 1110. applied if, following the sampling procedure shown in figure Figure 1 of this annex, the deviations of the measured values of the headlamps are: 2.3.1. Sample A : A4: one One headlamp not more than One headlamp more than 20 per cent one headlamp more than 30 per cent A5: both Both headlamps more than 20 per cent 2.3.2. cent Sample B B4: in In the case of A2 one One headlamp more than But not more than One headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in In the case of A2 both Both headlamps more than 20 per cent B6: in In the case of A2 one One headlamp One headlamp more than 0 per cent one headlamp more than 30 per cent 2.3.1. Sample A 2.3.2.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample A A1: one headlamp 0 per cent one headlamp not more than 0 per cent 20 per cent A2: both headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent Go to sample B cent 2.1.1.2. Sample B B1: both headlamps 0 per cent 2.1.2. Or, if the conditions of paragraph 1.2.2. above for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample A : A3: one headlamp one headlamp but not more than more than not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. cent Sample B B2: in the case of A2 one headlamp more than 0 per cent but one headlamp not more than not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp but more than not more than 20 per cent but not more than 30 per cent 2.2.1.1. Sample A 2.2.1.2. 2.2.2. Or, if the conditions of paragraph 1.2.2. above for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 1112. of this Regulation applied if, following the sampling procedure shown in figure Figure 1 of this annex, the deviations of the measured values of the headlamps are: 2.3.1. Sample A : A4: one headlamp one headlamp not more than more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. cent Sample B B4: in the case of A2 one headlamp more than 0 per cent but one headlamp not more than more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per centcent 2.3.1. Sample A 2.3.2.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested: 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample A A1: one One headlamp 0 per cent one One headlamp not more than 20 per cent A2: both Both headlamps more than 0 per cent but But not more than 20 per cent Go to sample B 0 per cent 20 per cent 2.1.1.2. Sample B B1: both Both headlamps 0 per cent 2.1.2. Or if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested: 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample A A3: one One headlamp not more than 20 per cent one One headlamp more than 20 per cent but But not more than 30 per cent 2.2.1.2. Sample B B2: in In the case of A2 one One headlamp more than 0 per cent but But not more than 20 per cent one One headlamp not more than 20 per cent B3: in In the case of A2 one One headlamp 0 per cent one One headlamp more than 20 per cent but But not more than 30 per cent 2.2.2. Or if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 1110. applied if, following the sampling procedure shown in figure Figure 1 of this annex, the deviations of the measured values of the headlamps are: 2.3.1. Sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per centA 2.3.2. Sample B B4: in In the case of A2 one One headlamp more than But not more than One headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in In the case of A2 both Both headlamps more than 20 per cent B6: in In the case of A2 one One headlamp One headlamp more than 0 per cent one headlamp more than 30 per cent 2.3.3. Or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample A A1: one headlamp 0 per cent one headlamp not more than 0 per cent 20 per cent A2: both headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent Go to sample B cent 2.1.1.2. Sample B B1: both headlamps 0 per cent 2.1.2. Or, if the conditions of paragraph 1.2.2. above for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample A : A3: one headlamp one headlamp but not more than more than not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. cent Sample B B2: in the case of A2 one headlamp more than 0 per cent but one headlamp not more than not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp but more than not more than 20 per cent but not more than 30 per cent 2.2.1.1. Sample A 2.2.1.2. 2.2.2. Or, if the conditions of paragraph 1.2.2. above for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 1112. of this Regulation applied if, following the sampling procedure shown in figure Figure 1 of this annex, the deviations of the measured values of the headlamps are: 2.3.1. Sample A : A4: A5: one headlamp one headlamp both headlamps not more than more than more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. cent Sample B B4: in the case of A2 one headlamp more than 0 per cent but one headlamp not more than more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per centcent 2.3.1. Sample A 2.3.2.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go go to sample B 2.1.1.2. Sample sample B B1: both headlamps 0 per cent 2.1.2. or if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.2. or if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per centsample A 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent 2.3.3. or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go go to sample B 2.1.1.2. Sample sample B B1: both headlamps 0 per centcent 2/ See footnote 15/ of the text of the Regulation. 2.1.2. or if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.2. or if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent 2.3.3. or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go go to sample B 2.1.1.2. Sample sample B B1: both headlamps 0 per cent 2.1.2. or if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.2. or if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent 2.3.3. or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 0 per cent 20 per cent A2: both headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent Go to sample B cent 2.1.1.2. Sample sample B B1: both headlamps 0 per cent 2.1.2. or, if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but one headlamp not more than not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp but more than not more than 20 per cent but not more than 30 per cent 2.2.2. or, if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent 2.3.3. or, if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 0 per cent 20 per cent A2: both headlamps more than 0 per cent but But go to sample B not more than 20 per cent Go to cent 1.1.2. sample B 2.1.1.2. Sample B B1: both headlamps 0 per cent 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent cent 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure Figure 1 of this annex, the deviations of the measured values of the headlamps are: : 2.3.1. Sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per centsample A 2.3.2. Sample sample B B4: in the case of A2 one headlamp but one headlamp more than not more than more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent 3. REPEATED SAMPLING In the case of A3, B2, B3 a repeated sampling, third sample C of two headlamps, selected from stock manufactured after alignment, is necessary within two months' time after the notification. 3.1. The conformity is not contested 3.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps are: 3.1.1.1. sample C 1.1.2. sample D D1: in the case of C2 both headlamps 0 per cent 3.2. The conformity is contested 3.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 3.2.1.1. sample D D2: in the case of C2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent 3.3. Approval withdrawn 3.3.1. sample C 3.3.2. sample D D3: in the case of C2 one headlamp 0 or more than 0 per cent one headlamp more than 20 per cent Abbreviations: P: passing beam lamp D: driving beam lamp (D1 + D2 means two driving beams) F: front fog lamp : means a cycle of 15 minutes off and 5 minutes lit. All following grouped headlamps and front fog lamps together with the added class B marking symbols are given as examples and are not exhaustive. 1. P or D or F (C-BS or R-BS or B) P, D or F 2. P+D (CR-BS) or P+D1+D2 (CR-BS R-BS)

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go go to sample B 2.1.1.2. Sample sample B B1: both headlamps 0 per cent 2.1.2. or if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.2. or if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both Both headlamps more than 20 per cent 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent 2.3.3. or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go go to sample B B 2.1.1.2. Sample sample B B1: both headlamps 0 per cent 2.1.2. or if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.2. or if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent 2.3.3. or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 0 per cent 20 per cent A2: both headlamps more than 0 per cent but But go to sample B not more than 20 per cent Go to cent 1.1.2. sample B 2.1.1.2. Sample B B1: both headlamps 0 per cent 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent cent 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure Figure 1 of this annex, the deviations of the measured values of the headlamps are: : 2.3.1. Sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per centsample A 2.3.2. Sample sample B B4: in the case of A2 one headlamp but one headlamp more than not more than more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent 3. REPEATED SAMPLING In the case of A3, B2, B3 a repeated sampling, third sample C of two headlamps, selected from stock manufactured after alignment, is necessary within two months' time after the notification. 3.1. The conformity is not contested 3.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps are: 3.1.1.1. sample C C1: one headlamp one headlamp not more than 0 per cent 20 per cent C2: both headlamps but go to sample D more than not more than 0 per cent 20 per cent 3.1.1.2. sample D D1: in the case of C2 both headlamps 0 per cent 3.2. The conformity is contested 3.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 3.2.1.1. sample D D2: in the case of C2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent 3.3. Approval withdrawn 3.3.1. sample C 3.3.2. sample D D3: in the case of C2 one headlamp 0 or more than 0 per cent one headlamp more than 20 per cent Abbreviations: P: passing beam lamp D: driving beam lamp (D1 + D2 means two driving beams) F: front fog lamp : means a cycle of 15 minutes off and 5 minutes lit. All following grouped headlamps and front fog lamps together with the added class B marking symbols are given as examples and are not exhaustive. 1. P or D or F (C-BS or R-BS or B) P, D or F 2. P+D (CR-BS) or P+D1+D2 (CR-BS R-BS)

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 0 per cent 20 per cent A2: both headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent Go to sample B cent 2.1.1.2. Sample sample B B1: both headlamps 0 per cent 2.1.2. or, if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp but one headlamp more than not more than not more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp but more than not more than 20 per cent but not more than 30 per cent 2.2.2. or, if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go go to sample B 2.1.1.2. Sample sample B B1: both headlamps 0 per cent 2.1.2. or, if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.2. or, if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample A A1: one headlamp 0 per cent one headlamp not more than 0 per cent 20 per cent A2: both headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent Go to sample B cent 2.1.1.2. Sample B B1: both headlamps 0 per cent 2.1.2. Or, if the conditions of paragraph 1.2.2. above for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample A : A3: one headlamp one headlamp but not more than more than not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. cent Sample B B2: in the case of A2 one headlamp more than 0 per cent but one headlamp not more than not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp but more than not more than 20 per cent but not more than 30 per cent 2.2.1.1. Sample A 2.2.1.2. 2.2.2. Or, if the conditions of paragraph 1.2.2. above for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 1110. applied if, following the sampling procedure shown in figure Figure 1 of this annex, the deviations of the measured values of the headlamps are: 2.3.1. Sample A : A4: one headlamp one headlamp not more than more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. cent Sample B B4: in the case of A2 one headlamp more than 0 per cent but one headlamp not more than more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per centcent 2.3.1. Sample A 2.3.2.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go go to sample B 2.1.1.2. Sample sample B B1: both headlamps 0 per centcent 2/ See footnote 15/ of the text of the Regulation. 2.1.2. or if the conditions of paragraph 1.2.2. for sample A are fulfilled. 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per per cent cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.2. or if the conditions of paragraph 1.2.2. for sample A are not fulfilled. 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per centsample A 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps A2 more than 20 per cent B6: in the case of A2 one headlamp A2 0 per cent one headlamp more than 30 per centcent 2.3.3. or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations deviation of the measured values of the headlamps in the unfavourable directions are: 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go go to sample B 2.1.1.2. Sample sample B B1: both headlamps 0 per cent 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per cent 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent

First sampling. In the first sampling four headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps in the unfavourable directions are:: E/ECE/324 Rev.2/Add.112 Regulation No. 113 page 41 Annex 7 2.1.1.1. Sample sample A A1: one headlamp 0 per cent one headlamp not more than 20 per cent A2: both headlamps more than 0 per cent but not more than 20 per cent Go go to sample B 2.1.1.2. Sample sample B B1: both headlamps 0 per cent 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in figure Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are: 2.2.1.1. Sample sample A A3: one headlamp not more than 20 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.2.1.2. Sample sample B B2: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp not more than 20 per cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent 2.3. Approval withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:withdrawn 2.3.1. Sample sample A A4: one headlamp not more than 20 per cent one headlamp more than 30 per cent A5: both headlamps more than 20 per centcent E/ECE/324 Rev.2/Add.112 Regulation No. 113 page 42 Annex 7 2.3.2. Sample sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one headlamp more than 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent