Correct Nonconformities. The contractor is responsible for correcting all nonconformities to the satisfaction of the design professional in responsible charge and the building official. BUILDING DEPARTMENT RESPONSIBILITIES
Correct Nonconformities Sample Clauses
Related to Correct Nonconformities
Correction of Errors Contractor shall perform, at its own cost and expense and without reimbursement from the District, any work necessary to correct errors or omissions which are caused by the Contractor’s failure to comply with the standard of care required herein.
Correction of Defects 35.1 The Engineer shall give notice to the Contractor of any Defects before the end of the Defects Liability Period, which begins at Completion and is defined in the Contract Data. The Defects Liability Period shall be extended for as long as Defects remain to be corrected.
Defective Product Seller must guarantee a return for all defective products. a) Goods rejected by Buyer for whatever reason shall be held, transported and/or stored at Seller’s sole expense. Seller shall promptly reimburse Buyer for any such expenses. B) Defective product purchase COD will be returned COD to Seller or COD check will be cancelled, at Buyer’s discretion. c) Seller is responsible for all costs associated RoHS noncompliance returns and will accept a full return for all parts not meeting RoHS compliance criteria if necessary. d) Seller is 100% responsible for all monetary and/or rework costs associated with product failures in addition to any further cost whatsoever associated with product failures. e) If suspect parts/counterfeit parts are furnished under this agreement such parts shall be impounded by Buyer. Buyer may provide a sample batch Supplier for verification and authentication. In addition, Buyer reserves the right to send such items to the appropriate manufacturer and appropriate authorities for investigation. f) Seller shall be liable for all costs relating to impound, investigation, removal, or replacement of suspect/counterfeit parts.
Latent Defects Notwithstanding anything to the contrary set forth herein, no acceptance, or deemed acceptance, by City pursuant to this Section shall be applicable with respect to any Latent Defects. An acceptance, or deemed acceptance, by City pursuant to this Section shall not mean that City has accepted, or the other party has been relieved of, responsibility for: (i) compliance with the Laws; (ii) the proper application of construction means or methods; or (iii) correcting any portion of the Project if it later is determined that any portion of the Project is inconsistent with the Final Documents and Drawings.
Correction No corrections shall be made in the tender documents. Any corrections that are to be made shall be made by crossing the incorrect portion and writing the correct portions above with the initials of tenderer.
Inspection and Rejection of Nonconforming Goods (a) Buyer shall inspect the goods within five days of receipt (“Inspection Period”). Xxxxx will be deemed to have accepted the goods unless it notifies Seller in writing of any Nonconforming Goods during the Inspection Period and furnishes documentation reasonably required by Seller. “
Quality of Materials and Workmanship Unless otherwise specified, all materials shall be new, and both workmanship and materials shall be of good quality. The Contractor shall, if required, furnish satisfactory evidence as to the kind and quality of materials and work. The burden of proof is on the Contractor.
Manufacturer’s Warranty The Goods include the manufacturer’s standard limited parts warranty to replace defective parts covered under such warranty exclusive of labor. Labor is warranted by the Elevator Contractor for 90 days following installation. The manufacturer’s parts warranty may require that the Goods be maintained throughout the warranty period by an authorized manufacturer’s representative under a separate maintenance contract. Any warranty is conditioned on written notice to the Elevator Contractor within warranty period and contingent upon receipt of final payment to Elevator Contractor.
ODUF Packing Specifications 6.3.1 The data will be packed using ATIS EMI records. A pack will contain a minimum of one (1) message record or a maximum of ninety-nine thousand nine hundred and ninety-nine (99,999) message records plus a pack header record and a pack trailer record. One transmission can contain a maximum of ninety-nine (99) packs and a minimum of one (1) pack.
Packing Specifications 7.3.1 A pack will contain a minimum of one message record or a maximum of 99,999 message records plus a pack header record and a pack trailer record. One transmission can contain a maximum of 99 packs and a minimum of one pack.
