Conditions in the mist chamber Sample Clauses
The 'Conditions in the mist chamber' clause defines the specific environmental parameters that must be maintained within a mist chamber, such as temperature, humidity, and misting frequency. In practice, this clause may require the operator to monitor and regulate these factors to ensure optimal conditions for the items or processes taking place inside the chamber, such as plant propagation or material testing. By clearly outlining these requirements, the clause ensures consistency and reliability in outcomes, and helps prevent disputes over whether proper conditions were maintained.
Conditions in the mist chamber. 5.1. The exposure zone of the mist chamber shall be maintained at 35 ± 5°C. At least two clean mist collectors shall be placed within the exposure zone, so that no drops of solution from the test samples or any other sources are collected. The collectors shall be placed near the test samples, one as near as possible to any nozzle and one as far as possible from all nozzles. The mist shall be such that, for each 80 cm2 of horizontal collecting area, from 1.0 to 2.0 ml of solution per hour, when measured over an average of at least 16 hours, is collected in each collector.
5.2. The nozzle or nozzles shall be directed or baffled, so that the spray does not impinge directly on the test samples.
Conditions in the mist chamber. 5.1. The exposure zone of the mist chamber shall be maintained at 35 ± 5°C. At least two clean mist collectors shall be placed within the exposure zone, so that no drops of solution from the test samples or any other sources are collected. The collectors shall be placed near the test samples, one as near as possible to any nozzle and one as far as possible from all nozzles. The mist shall be such that, for each 80 cm2 of horizontal collecting area, from 1.0 to 2.0 ml of solution per hour, when measured over an average of at least 16 hours, is collected in each collector.
5.2. The nozzle or nozzles shall be directed or baffled, so that the spray does not impinge directly on the test samples. Annex 5 total travel: 300 ± 20 mm protective strap for inner bar support Example a total travel: 300 ± 20 mm rotating pin lower stop Example b Examples of test arrangements corresponding to the type of adjusting device F = 10 ± 0.1 N Annex 5 30 ± 5° total travel: 300 ± 20 mm straps in horizontal plane F = 5 ± 0.05 N total travel: 300 ± 20 mm 25 ± 5º 25 ± 5º F = 5 ± 0.05 N Annex 5 200 mm. min. adjusting device strap attached by stitching F = 50 ± 0.5 N 100 ± 20 mm taut position slack position The load of 50 N on the testing device shall be vertically guided in such a way as to prevent load-swing and twisting of the strap. The attaching device shall be fixed to the load of 50 N in the same manner as in the vehicle.
Conditions in the mist chamber. 5.1. The exposure zone of the mist chamber shall be maintained at 35 ± 5°C. At least two clean mist collectors shall be placed within the exposure zone, so that no drops of solution from the test samples or any other sources are collected. The collectors shall be placed near the test samples, one as near as possible to any nozzle and one as far as possible from all nozzles. The mist shall be such that, for each 80 cm2 of horizontal collecting area, from 1.0 to 2.0 ml of solution per hour, when measured over an average of at least 16 hours, is collected in each collector.
5.2. The nozzle or nozzles shall be directed or baffled, so that the spray does not impinge directly on the test samples. E/ECE/324 E/ECE/TRANS/505 page 33 Annex 6 DESCRIPTION OF TROLLEY } Rev.1/Add.43/Rev.2
Conditions in the mist chamber. 5.1. The exposure zone of the mist chamber shall be maintained at 35 ± 5°C. At least two clean mist collectors shall be placed within the exposure zone, so that no drops of solution from the test samples or any other sources are collected. The collectors shall be placed near the test samples, one as near as possible to any nozzle and one as far as possible from all Deleted: CRS‐60‐01e.docx2¶ Formatted: English (U.K.) Formatted: English (U.K.) nozzles. The mist shall be such that, for each 80 cm2 of horizontal collecting area, from 1.0 to