Communications Installation Sample Clauses
The Communications Installation clause outlines the requirements and procedures for setting up communication systems within a project or property. It typically specifies the types of equipment to be installed, the standards to be followed, and the responsibilities of each party involved, such as providing access or ensuring compatibility with existing infrastructure. By clearly defining these expectations, the clause helps prevent disputes over installation quality, timing, and responsibility, ensuring that communication systems are properly integrated and functional.
Communications Installation. Category Meter Provision No. MP - 6 Service Description Communications Installation This Service is an Extended Metering Service. This Service may be requested by the User to install and activate a communications link. Where requesting this Service for a Meter that cannot accommodate a communications link, the User must also request a Meter exchange Service (MP-4). Upon completion of this Service, Western Power will operate and maintain the communications link as a Standard Metering Service. This Service description should be read in conjunction with the Code and the Communication Rules, which incorporate the Build Pack. The Build Pack, including the WA B2B Procedures: Service Order Process, defines specific detail as to the business processes and B2B transactions associated with the provision of this Service. A Reconfigure Service Order in accordance with the Communication Rules. The Meter is a model and configuration suitable for the Service being requested.
Communications Installation. (Data, Telephone, Fiber Optics. Etc.)
1. All passage of communication cables through fire rated partitions must be sealed and fire-stopped in accordance with current regulations.
2. All cables installed in plenum spaces must be approved and rated for plenum use or be installed in a plenum rated enclosure.
3. Where approved cables are allowed and used, all cables must be installed in bundles and independently fastened to the slab above so as not to impose an additional load on ceiling systems, HVAC systems, electrical systems, etc. All exposed cables within the Building’s usable space must be installed in conduit or Building approved equal.
Communications Installation. Category Meter Provision No. MP - 4 Service Description Communications Installation This Service is an Extended Metering Service. This Service may be requested by the User to install and activate a communications link. Where requesting this Service for a Meter that cannot accommodate a communications link, the User must also request a Meter exchange Service (MP-2).
Communications Installation. Category Meter Provision No. MP - 64 Service Description Communications Installation This Service is an Extended Metering Service. This Service may be requested by the User to install and activate a communications link. Where requesting this Service for a Meter that cannot accommodate a communications link, the User must also request a Meter exchange Service (MP-42). Upon completion of this Service, Western Power will operate and maintain the communications link as a Standard Metering Service. This Service description should be read in conjunction with the Code and the Communication Rules, which incorporate the Build Pack. The Build Pack, including the WA B2B Procedures: Service Order Process, defines specific detail as to the business processes and B2B transactions associated with the provision of this Service. A Reconfigure Service Order in accordance with the Communication Rules. The Meter is a model and configuration suitable for the Service being requested. Category Meter Provision No. MP - 75 Service Description Meter Test (laboratory) This Service is an Extended Metering Service. The Service may be requested by the User to test or audit the accuracy of a Metering Installation. Testing will be carried out in a National Association of Testing Authorities (NATA)n accredited laboratory under various load conditions, using reference standards that are traceable to national standards. Performance characteristics are monitored, such as ‘running at no-load’ (creep) and ‘operation of register or display’, for correct operation. A report will be issued to the User on the finding of the tests. In addition a weighted average of the overall accuracy of the Meter will beis calculated and provided tofor the User. to determine the compensation to Customers, if any. Where an outage or malfunction to a Metering Installation is confirmed, Western Power will complete a Metering Installation repair (MP-2), subject to the discretion noted in that Service description to replace the Meter instead.Where discrepancies are discovered, Western Power will complete a Metering Installation repair (MP-1). This Service description should be read in conjunction with the Code and the Communication Rules, which incorporate the Build Pack. The Build Pack, including the WA B2B Procedures: Service Order Process, defines specific detail as to the business processes and B2B transactions associated with the provision of this Service. A Meter Investigation – Meter Test Service Order in...
Communications Installation. Lessee intends to install a conduit, four (4) inches in diameter from its building at ▇▇▇▇▇ ▇▇▇▇▇▇▇ ▇▇▇▇▇▇, ▇▇▇▇▇▇▇▇ ▇▇▇▇▇▇▇▇▇▇ across Mariner Avenue to the Premises and to run through such conduit a 300 pair 24 gauge cable, a fiber optic cable and an innerduct. The aforesaid conduit, cables and innerduct, together with all related plans, designs, parts, equipment, terminations, couplings and other components, shall hereinafter be collectively referred to as the "Communications Installation. In connection with the Communications Installation it is agreed that:
(a) The Communications Installation shall be designed, installed, used, maintained and/or removed solely at the expense of Lessee and at no cost, liability or expense whatsoever to Lessor. Lessee shall be solely responsible for the design and function of the Communications Installation. In connection with designing, installing, using, maintaining and/or removing the Communications Installation, Lessee shall promptly comply, or cause compliance with all laws, ordinances, zoning, zoning variances, orders, rules, regulations and requirements (including, without limitation, obtaining all building and other permits required) of all federal, state, county, township and municipal governments and all departments, commissions, boards and officers thereof, whether present or future, foreseen or unforeseen, ordinary or extraordinary, and whether or not the same shall be presently within the contemplation of Lessor and Lessee or shall involve any change of governmental policy, or require alterations or additions, and irrespective of the cost thereof, At the end of the Lease term, if so requested by Lessor, Lessee shall remove such portion of the Communications Installation as is installed in, on or upon the Building Project or any portion thereof and shall repair the Building Project to the extent required and in accordance with the provisions of Paragraph 8.2 above. The location of the Communications Installation shall be as set forth on Exhibit "E" attached hereto. In connection with the Communications Installation Lessee shall comply with all of the provisions of Paragraph 8.4 above other than obtaining the written consent of Lessor to the Communications Installation. In addition Lessee shall repair to the condition existing prior to such installation any and all landscaping, asphalt, sidewalks, parking areas, floors, walls, foundations or other improvements within the Building Project which are in any way di...
Communications Installation. Upon approval by the Government, the Contractor shall provide all activities associated with installation and Government operation of the network designed as a result of the Communications Design task stated in Section 3.5.2, above. Some of the activities included in this task are: site survey; installation and testing of the equipment peripherals, cabling and data links; and operational training. Communications installation activities will follow the procedures described in individual delivery order requirements. Computer resources necessary for installation activities will be either Government provided or will be Contractor provided.