ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. Contractor hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of Contractor's work on the Project for District. Contractor further certifies that it has instructed its employees with respect to the above- mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by Contractor if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at Contractor's expense at no additional cost to the District. Contractor has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of Contractor: Signature: Print Name: Title: LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California Department of Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate lead-containing paint and lead products. Because the Contractor and its employees will be providing services for the District, and because the Contractor’s work may disturb lead-containing building materials, CONTRACTOR IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a lead- based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the Contractor, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. The Contractor shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the Contractor. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. Contractor, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, the Contractor will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the Contractor to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of the Contractor to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. THE UNDERSIGNED HEREBY ACKNOWLEDGES, UNDER PENALTY OF PERJURY, THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD-BASED MATERIALS ON THE OWNER’S PROPERTY, AS WELL AS THE EXISTENCE OF APPLICABLE LAWS, RULES AND REGULATIONS GOVERNING WORK WITH, AND DISPOSAL OF, SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR.

Appears in 17 contracts

Samples: Agreement for Construction Services, Executed Contract, Agreement for Construction Services

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. Contractor hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of Contractor's work on the Project for District. Contractor further certifies that it has instructed its employees with respect to the above- mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by Contractor if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at Contractor's expense at no additional cost to the District. Contractor has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of Contractor: Signature: Print Name: Title: LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California Department of Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate lead-containing paint and lead products. Because the Contractor and its employees will be providing services for the District, and because the Contractor’s work may disturb lead-containing building materials, CONTRACTOR IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a lead- based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the Contractor, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. The Contractor shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the Contractor. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. Contractor, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, the Contractor will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the Contractor to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of the Contractor to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. THE UNDERSIGNED ~~HEREBY~~ XXXXXX ACKNOWLEDGES, UNDER PENALTY OF PERJURY, THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD-BASED MATERIALS ON THE OWNER’S PROPERTY, AS WELL AS THE EXISTENCE OF APPLICABLE LAWS, RULES AND REGULATIONS GOVERNING WORK WITH, AND DISPOSAL OF, SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR.

Appears in 2 contracts

Samples: Executed Contract, Agreement for Construction Services

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. ~~Contractor~~ Design-Builder hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of ~~Contractor~~Design- Builder's work on the Project for District. ~~Contractor~~ Design-Builder further certifies that it has instructed its employees with respect to the ~~above-~~ above-mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by ~~Contractor~~ Design-Builder if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at ~~Contractor~~Design-Builder's expense at no additional cost to the District. ~~Contractor~~ Design-Builder has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of ~~Contractor~~Design-Builder: Signature: Print Name: Title: LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California Department of Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate ~~lead-~~lead- containing paint and lead products. Because the ~~Contractor~~ Design-Builder and its employees will be providing services for the District, and because the ~~Contractor~~Design-Builder’s work may disturb lead-containing building materials, ~~CONTRACTOR~~ DESIGN- BUILDER IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a ~~lead-~~ lead-based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the ~~Contractor~~Design-Builder, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. ~~The Contractor~~ Design-Builder shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the ~~Contractor~~Design- Builder. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. ~~Contractor~~Design-Builder, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, ~~the Contractor~~ Design-Builder will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the ~~Contractor~~ Design-Builder to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of ~~the Contractor~~ Design-Builder to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. ~~THE UNDERSIGNED HEREBY ACKNOWLEDGES~~The undersigned hereby acknowledges, ~~UNDER PENALTY OF PERJURY~~under penalty of perjury, ~~THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD~~that he or she has received notification of potential lead-~~BASED MATERIALS ON THE OWNER’S PROPERTY~~based materials on the owner’s property, ~~AS WELL AS THE EXISTENCE OF APPLICABLE LAWS~~as well as the existence of applicable laws, ~~RULES AND REGULATIONS GOVERNING WORK WITH~~rules and regulations governing work with, ~~AND DISPOSAL OF~~and disposal of, ~~SUCH MATERIALS WITH WHICH IT MUST COMPLY~~such materials with which it must comply. ~~THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR~~The undersigned also warrants that he or she has the authority to sign on behalf of and bind the design-builder. Date: Name of Design-Builder: Signature: Print Name: Title: 24 Agreement For Design, Installation and Commissioning of Solar/Photovoltaic System between Xxxxxx Community College District and PERFORMANCE BOND (100% of Contract Price) (Note: Respondents must use this form, NOT a surety company form.) KNOW ALL PERSONS BY THESE PRESENTS: That WHEREAS, the governing board (“Board”) of the Xxxxxx Community College District, (“District”) and , (“Principal)” have entered into a contract for the furnishing of all materials and labor, services and transportation, necessary, convenient, and proper to perform the following project: (Project Name) (“Project” or “Contract”) which Contract dated , 20 , and all of the Contract Documents attached to or forming a part of the Contract, are hereby referred to and made a part hereof, and And WHEREAS, said Principal is required under the terms of the Contract to furnish a bond for the faithful performance of the Contract;

Appears in 2 contracts

Samples: Agreement, Agreement

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. Contractor hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations (“New ~~Material Hazardous~~Hazardous Material”), shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of Contractor's work on the Project for District. Contractor further certifies that it has instructed its employees with respect to the above- mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by Contractor if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous ~~Material”~~ Material containing equipment will be immediately rejected and this Work will be removed at Contractor's expense at no additional cost to the District. Contractor has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of Contractor: Signature: Print Name: Title: ~~LEAD-PRODUCT(S~~REGISTERED SUBCONTRACTORS LIST (Labor Code Section 1771.1) ~~CERTIFICATION California Occupational Safety~~ PROJECT: Date Submitted (for Updates): Contractor acknowledges and ~~Health Administration (CalOSHA), Environmental Protection Agency (EPA), California~~ agrees that it must clearly set forth below the name and Department of ~~Health Services~~ Industrial Relations (~~DHS), California Department~~ DIR) registration number of ~~Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate lead-containing paint and lead products. Because the~~ each subcontractor for all tiers who will perform work or labor or render service to Contractor ~~and~~ or its employees will be providing services for the District, and because the Contractor’s work may disturb lead-containing building materials, CONTRACTOR IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a lead- based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the Contractor, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in ~~the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use~~ or ~~import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in~~ about the construction of the Work at least two (2) weeks before the subcontractor is scheduled to perform work. This document is to be updated as all tiers of subcontractors are identified. Contractor acknowledges and agrees that, if Contractor fails to list as to any ~~new school facility or in the modernization or renovation~~ subcontractor of any ~~existing school facility. The Contractor shall provide the District with~~ tier who performs any ~~sample results prior to beginning Work, during the Work, and after the completion~~ portion of ~~the Work. The District may request to examine, prior to the commencement of the~~ Work, the lead training records of each employee of the Contractor. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair Contract is subject to cancellation and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. Contractor, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, the Contractor will be ~~held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant~~ subjected to ~~the indemnification provisions of the Contract, for all damages and other claims arising therefrom~~penalty under applicable law. If ~~lead disturbance~~ further space is ~~anticipated in~~ required for the list of proposed subcontractors, attach additional copies of page 2 showing the required information, as indicated below. Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Date: Name of Contractor: Signature: Print Name: Title: PERFORMANCE BOND (100% of Contract Price) (Note: Contractor must use this form, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the Contractor to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of the Contractor to provide the proper disposal of any hazardous waste by NOT a ~~certified hazardous waste hauler. This~~ surety company ~~shall be registered with the Department of Transportation (DOT~~form.) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. THE UNDERSIGNED HEREBY ACKNOWLEDGES, UNDER PENALTY OF PERJURY, THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD-BASED MATERIALS ON THE OWNER’S PROPERTY, AS WELL AS THE EXISTENCE OF APPLICABLE LAWS, RULES AND REGULATIONS GOVERNING WORK WITH, AND DISPOSAL OF, SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR.KNOW ALL PERSONS BY THESE PRESENTS:

Appears in 1 contract

Samples: Agreement for Routine Maintenance Services

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. ~~Contractor~~ Design-Builder hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of ~~Contractor~~Design-Builder's work on the Project for District. ~~Contractor~~ Design-Builder further certifies that it has instructed its employees with respect to the ~~above-~~ above-mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by ~~Contractor~~ Design-Builder if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at ~~Contractor~~Design-Builder's expense at no additional cost to the District. ~~Contractor~~ Design-Builder has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of ~~Contractor~~Design-Builder: Signature: Print Name: Title: LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California Department of Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate lead-containing paint and lead products. Because the ~~Contractor~~ Design-Builder and its employees will be providing services for the District, and because the ~~Contractor~~Design-Builder’s work may disturb lead-containing building materials, ~~CONTRACTOR~~ DESIGN-BUILDER IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a ~~lead-~~ lead-based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the ~~Contractor~~Design-Builder, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. ~~The Contractor~~ Design-Builder shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the ~~Contractor~~Design-Builder. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. ~~Contractor~~Design-Builder, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, ~~the Contractor~~ Design-Builder will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the ~~Contractor~~ Design-Builder to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of ~~the Contractor~~ Design-Builder to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. ~~THE UNDERSIGNED HEREBY ACKNOWLEDGES~~The undersigned hereby acknowledges, ~~UNDER PENALTY OF PERJURY~~under penalty of perjury, ~~THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD~~that he or she has received notification of potential lead-~~BASED MATERIALS ON THE OWNER’S PROPERTY~~based materials on the owner’s property, ~~AS WELL AS THE EXISTENCE OF APPLICABLE LAWS~~as well as the existence of applicable laws, ~~RULES AND REGULATIONS GOVERNING WORK WITH~~rules and regulations governing work with, ~~AND DISPOSAL OF~~and disposal of, ~~SUCH MATERIALS WITH WHICH IT MUST COMPLY~~such materials with which it must comply. ~~THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR~~The undersigned also warrants that he or she has the authority to sign on behalf of and bind the design-builder. Date: Name of Design-Builder: Signature: Print Name: Title: PERFORMANCE BOND (100% of Contract Price) (Note: Respondents must use this form, NOT a surety company form.) KNOW ALL PERSONS BY THESE PRESENTS: That WHEREAS, the governing board (“Board”) of the Xxxxxx Community College District, (“District”) and , (“Principal)” have entered into a contract for the furnishing of all materials and labor, services and transportation, necessary, convenient, and proper to perform the following project: (Project Name) (“Project” or “Contract”) which Contract dated , 20___, and all of the Contract Documents attached to or forming a part of the Contract, are hereby referred to and made a part hereof, and And WHEREAS, said Principal is required under the terms of the Contract to furnish a bond for the faithful performance of the Contract;

Appears in 1 contract

Samples: Agreement

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. ~~Contractor~~ Design-Builder hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of ~~Contractor~~Design-Builder's work on the Project for District. ~~Contractor~~ Design-Builder further certifies that it has instructed its employees with respect to the ~~above-~~ above-mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by ~~Contractor~~ Design-Builder if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at ~~Contractor~~Design-Builder's expense at no additional cost to the District. ~~Contractor~~ Design-Builder has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Proper Name of ~~Contractor~~Design-Builder: Signature: Print Name: Title: ~~LEAD~~Schedule Fremont System Schedule: Fremont Schedule Days Cumulative Total Days Notes Contract Execution Milestone Design and Permitting 131 131 1, 2 DSA Approval Milestone Procurement 87 218 Construction 75 293 Closeout Period 21 314 Notes: 1 Includes 21 days for DSA approval 2 Includes 14 cumulative days for customer approvals and comments Includes 7 days per submittal 3 Includes 5 rain days. A rain day is a 24 hour period in which .25 of an inch of precipitation occurs on a work day. Assumptions: At the time of DSA approval the following circumstances will exist: -Time and costs will be determined for PG&E interconnection and utility upgrades -CEQA approval will be obtained If the above is not received or determined by the time Design-~~PRODUCT(S) CERTIFICATION California Occupational Safety~~ Builder receives DSA approval, any consquent effect on critical path items will result in commensurate day for day extensions to the applicable Completion Date and ~~Health Administration~~ the date upon which liquidated damages begin accruing against the Design-Builder. This Schedule assumes that key critical path items not within Design Builder’s control will occur within reasonable time periods as noted above. Between the Effective Date of this Agreement and the date of permit issuance by the Division of State Architect (~~CalOSHA~~“DSA”), ~~Environmental Protection Agency~~ any delay of a critical path item shall only extend the Final Completion Date if the DSA permit issuance date is more than 131 days after the Effective Date of this Agreement. Subsequent to the DSA permit issuance date, to the extent a key critical path item has not occurred, through no fault of Design Builder, the Final Completion Date shall be extended on a day for day basis for each day beyond the applicable time period set forth in the Schedule that the key critical path has not been achieved. Newark System Schedule: Newark Schedule Days Cumulative Total Days Notes Contract Execution Milestone Design and Permitting 134 134 1, 2 DSA Approval Milestone Procurement 90 224 Construction 135 359 Closeout Period 21 380 Notes: 1 Includes 21 days for DSA approval 2 Includes 14 cumulative days for customer approvals and comments Includes 7 days per submittal 3 Includes 5 rain days. A rain day is a 24 hour period in which .25 of an inch of precipitation occurs on a work day. Assumptions: At the time of DSA approval the following circumstances will exist: -Time and costs will be determined for PG&E interconnection and utility upgrades -CEQA approval will be obtained If the above is not received or determined by the time Design-Builder receives DSA approval, any consquent effect on critical path items will result in commensurate day for day extensions to the applicable Completion Date and the date upon which liquidated damages begin accruing against the Design-Builder. This Schedule assumes that key critical path items not within Design Builder’s control will occur within reasonable time periods as noted above. Between the Effective Date of this Agreement and the date of permit issuance by the Division of State Architect (~~EPA~~“DSA”), ~~California Department~~ any delay of ~~Health Services~~ a critical path item shall only extend the Final Completion Date if the DSA permit issuance date is more than 134 days after the Effective Date of this Agreement. Subsequent to the DSA permit issuance date, to the extent a key critical path item has not occurred, through no fault of Design Builder, the Final Completion Date shall be extended on a day for day basis for each day beyond the applicable time period set forth in the Schedule that the key critical path has not been achieved. Change in Scope of Work With the exception of change orders for alternate Systems based on the Executive Summary and Drawings (~~DHS)~~Exhibit “C”) hereto, ~~California Department of Education (CDE),~~ the following format shall be used as applicable by the District and the ~~Consumer Product Safety Commission~~ Design-Builder (~~CPSC~~e.g. Change Orders, PCO’s) regulate lead-containing paint and lead products. Because the Contractor and its employees will be providing services for the District, and because the Contractor’s work may disturb lead-containing building materials, CONTRACTOR IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to ~~1993 are presumed~~ communicate proposed additions to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a lead- based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the Contractor, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. The Contractor shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the Contractor. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. Contractor, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, the Contractor will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, ~~for all damages and other claims arising therefrom~~supported by attached documentation. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the Contractor to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of the Contractor to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. THE UNDERSIGNED HEREBY ACKNOWLEDGES, UNDER PENALTY OF PERJURY, THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEADWORK PERFORMED OTHER THAN BY DESIGN-BASED MATERIALS ON THE OWNER’S PROPERTY, AS WELL AS THE EXISTENCE OF APPLICABLE LAWS, RULES AND REGULATIONS GOVERNING WORK WITH, AND DISPOSAL OF, SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR.BUILDER ADD

Appears in 1 contract

Samples: Agreement

Appears in 1 contract

Samples: Agreement for Construction Services Agreement

Appears in 1 contract

Samples: Agreement for Construction Services Agreement Number 01

Appears in 1 contract

Samples: Tahoe Truckee Unified School District Agreement for Construction Services

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. ~~Contractor~~ Design-Builder hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of ~~Contractor~~Design- Builder's work on the Project for District. ~~Contractor~~ Design-Builder further certifies that it has instructed its employees with respect to the ~~above-~~ above-mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by ~~Contractor~~ Design-Builder if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at ~~Contractor~~Design-Builder's expense at no additional cost to the District. ~~Contractor~~ Design-Builder has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of ~~Contractor~~Design-Builder: Signature: Print Name: Title: LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California Department of Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate ~~lead-~~lead- containing paint and lead products. Because the ~~Contractor~~ Design-Builder and its employees will be providing services for the District, and because the ~~Contractor~~Design-Builder’s work may disturb lead-containing building materials, ~~CONTRACTOR~~ DESIGN- BUILDER IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a ~~lead-~~ lead-based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the ~~Contractor~~Design-Builder, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. ~~The Contractor~~ Design-Builder shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the ~~Contractor~~Design- Builder. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. ~~Contractor~~Design-Builder, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, ~~the Contractor~~ Design-Builder will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the ~~Contractor~~ Design-Builder to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of ~~the Contractor~~ Design-Builder to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. ~~THE UNDERSIGNED HEREBY ACKNOWLEDGES~~The undersigned hereby acknowledges, ~~UNDER PENALTY OF PERJURY~~under penalty of perjury, ~~THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD~~that he or she has received notification of potential lead-~~BASED MATERIALS ON THE OWNER’S PROPERTY~~based materials on the owner’s property, ~~AS WELL AS THE EXISTENCE OF APPLICABLE LAWS~~as well as the existence of applicable laws, ~~RULES AND REGULATIONS GOVERNING WORK WITH~~rules and regulations governing work with, ~~AND DISPOSAL OF~~and disposal of, ~~SUCH MATERIALS WITH WHICH IT MUST COMPLY~~such materials with which it must comply. ~~THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR~~The undersigned also warrants that he or she has the authority to sign on behalf of and bind the design-builder. Date: Name of Design-Builder: Signature: Print Name: Title: Agreement For Design, Installation and Commissioning for Lighting Energy Efficiency Project between Xxxxxx Community College District and PERFORMANCE BOND (100% of Contract Price) (Note: Respondents must use this form, NOT a surety company form.) KNOW ALL PERSONS BY THESE PRESENTS: That WHEREAS, the governing board (“Board”) of the Xxxxxx Community College District, (“District”) and , (“Principal)” have entered into a contract for the furnishing of all materials and labor, services and transportation, necessary, convenient, and proper to perform the following project: (Project Name) (“Project” or “Contract”) which Contract dated , 20 , and all of the Contract Documents attached to or forming a part of the Contract, are hereby referred to and made a part hereof, and And WHEREAS, said Principal is required under the terms of the Contract to furnish a bond for the faithful performance of the Contract;

Appears in 1 contract

Samples: www.solano.edu

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. ~~Contractor~~ DB Entity hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of ~~Contractor~~DB Entity's work on the Project for ~~District~~Owner. ~~Contractor~~ DB Entity further certifies that it has instructed its employees with respect to the ~~above-~~ above-mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at ~~the District~~Owner’s determination. The costs of any such tests shall be paid by ~~Contractor~~ DB Entity if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at ~~Contractor~~DB Entity's expense at no additional cost to ~~the District~~Owner. ~~Contractor~~ Design-Builder has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of ~~Contractor~~DB Entity: Signature: Print Name: Title: ~~LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety~~ EXHIBIT 7 PERFORMANCE BOND CITY OF MODESTO KNOW ALL PERSONS BY THESE PRESENTS: That , as Principal, hereinafter called Contractor, and ~~Health Administration~~ , as Surety of Sureties, hereinafter called “Surety,” are held firmly bound unto the City of Modesto, as Obligee, hereinafter called “City,” in the sum of (~~CalOSHA~~$ ), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California Department of Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate lead-containing paint and lead products. Because the for which payment Contractor and ~~its employees will be providing services for the District~~Surety bind themselves, their heirs, executors, administrators, successors and ~~because the Contractor’s work may disturb lead-containing building materials~~assigns, ~~CONTRACTOR IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized~~ jointly and severally, firmly by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a lead- based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the Contractor, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. The Contractor shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the Contractor. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. Contractor, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, the Contractor will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the Contractor to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of the Contractor to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. THE UNDERSIGNED HEREBY ACKNOWLEDGES, UNDER PENALTY OF PERJURY, THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD-BASED MATERIALS ON THE OWNER’S PROPERTY, AS WELL AS THE EXISTENCE OF APPLICABLE LAWS, RULES AND REGULATIONS GOVERNING WORK WITH, AND DISPOSAL OF, SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTORpresents.

Appears in 1 contract

Samples: Design / Build Agreement

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. Contractor hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of Contractor's work on the Project for District. Contractor further certifies that it has instructed its employees with respect to the above- mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by Contractor if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at Contractor's expense at no additional cost to the District. Contractor has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of Contractor: Signature: Print Name: Title: END OF DOCUMENT LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California Department of Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate lead-containing paint and lead products. Because the Contractor and its employees will be providing services for the District, and because the Contractor’s work may disturb lead-containing building materials, CONTRACTOR IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a lead- based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the Contractor, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. The Contractor shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the Contractor. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. Contractor, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, the Contractor will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the Contractor to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of the Contractor to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. THE UNDERSIGNED ~~HEREBY~~ XXXXXX ACKNOWLEDGES, UNDER PENALTY OF PERJURY, THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD-BASED MATERIALS ON THE OWNER’S PROPERTY, AS WELL AS THE EXISTENCE OF APPLICABLE LAWS, RULES AND REGULATIONS GOVERNING WORK WITH, AND DISPOSAL OF, SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR. Date: Name of Contractor: Signature: Print Name: Title: END OF DOCUMENT DOCUMENT 00 61 13.13 PERFORMANCE BOND (100% of Contract Price) (Note: Contractor must use this form, NOT a surety company form.) KNOW ALL PERSONS BY THESE PRESENTS:

Appears in 1 contract

Samples: Agreement for Construction Services

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. Contractor hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations (“New ~~Material Hazardous~~Hazardous Material”), shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of Contractor's work on the Project for District. Contractor further certifies that it has instructed its employees with respect to the above- mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by Contractor if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous ~~Material”~~ Material containing equipment will be immediately rejected and this Work will be removed at Contractor's expense at no additional cost to the District. Contractor has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Contractor certifies that it is knowledgeable of, and shall comply with, all laws applicable to the Work including, but not limited to, all federal, state, and local laws, statutes, standards, rules, regulations, and ordinances applicable to the Work. Date: Name of Contractor: Signature: Print Name: Title: LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California ~~Department of Education~~ Community Colleges Chancellor’s Office (~~CDE~~CCCCO), and the Consumer Product Safety Commission (CPSC) regulate lead-containing paint and lead products. Because the Contractor and its employees will be providing services for the District, and because the Contractor’s work may disturb lead-containing building materials, CONTRACTOR IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. ~~The CDE mandates that school~~ Community college districts must utilize DHS lead-certified personnel when a ~~lead-~~ lead-based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the ~~district~~ District that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the Contractor, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. The Contractor shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the Contractor. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area or greater outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. Contractor, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, the Contractor will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the Contractor to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of the Contractor to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. THE UNDERSIGNED ~~HEREBY~~ XXXXXX ACKNOWLEDGES, UNDER PENALTY OF PERJURY, THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD-BASED MATERIALS ON THE OWNER’S PROPERTY, AS WELL AS THE EXISTENCE OF APPLICABLE LAWS, RULES AND REGULATIONS GOVERNING WORK WITH, AND DISPOSAL OF, SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR.. Date: Name of Contractor: Signature: Print Name: Title:

Appears in 1 contract

Samples: Agreement for Construction Services

Appears in 1 contract

Samples: Agreement for Construction Services

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. Contractor hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations (“New ~~Material Hazardous~~Hazardous Material”), shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of Contractor's work on the Project for District. Contractor further certifies that it has instructed its employees with respect to the above- mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by Contractor if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous ~~Material”~~ Material containing equipment will be immediately rejected and this Work will be removed at Contractor's expense at no additional cost to the District. Contractor has read and understood the document Hazardous Materials Procedures & ~~Requirements,~~ Requirements and shall comply with all the provisions outlined therein. Contractor certifies that it is knowledgeable of, and shall comply with, all laws applicable to the Work including, but not limited to, all federal, state, and local laws, statutes, standards, rules, regulations, and ordinances applicable to the Work. Date: Name of Contractor: Signature: Print Name: Title: LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California ~~Department of Education~~ Community Colleges Chancellor’s Office (~~CDE~~CCCCO), and the Consumer Product Safety Commission (CPSC) regulate lead-containing paint and lead products. Because the Contractor and its employees will be providing services for the District, and because the Contractor’s work may disturb lead-containing building materials, CONTRACTOR IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. ~~The CDE mandates that school~~ Community college districts must utilize DHS lead-certified personnel when a ~~lead-~~ lead-based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the ~~district~~ District that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the Contractor, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. The Contractor shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the Contractor. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area or greater outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. Contractor, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, the Contractor will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the Contractor to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of the Contractor to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. THE UNDERSIGNED ~~HEREBY~~ XXXXXX ACKNOWLEDGES, UNDER PENALTY OF PERJURY, THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD-BASED MATERIALS ON THE OWNER’S PROPERTY, AS WELL AS THE EXISTENCE OF APPLICABLE LAWS, RULES AND REGULATIONS GOVERNING WORK WITH, AND DISPOSAL OF, SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR.. Date: Name of Contractor: Signature: Print Name: Title: REGISTERED SUBCONTRACTORS LIST (Labor Code Section 1771.1) PROJECT: Date Submitted (for Updates): Contractor acknowledges and agrees that it must clearly set forth below the name and Department of Industrial Relations (DIR) registration number of each subcontractor for all tiers who will perform work or labor or render service to Contractor or its subcontractors in or about the construction of the Work at least two (2) weeks before the subcontractor is scheduled to perform work. This document is to be updated as all tiers of subcontractors are identified. Contractor acknowledges and agrees that, if Contractor fails to list as to any subcontractor of any tier who performs any portion of Work, the Contract is subject to cancellation and the Contractor will be subjected to penalty under applicable law. If further space is required for the list of proposed subcontractors, attach additional copies of page 2 showing the required information, as indicated below. Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Subcontractor Name: DIR Registration #: Portion of Work: Date: Name of Contractor: Signature: Print Name: Title:

Appears in 1 contract

Samples: Agreement for Construction Services

Appears in 1 contract

Samples: Agreement for Construction Services

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. Contractor hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of Contractor's work on the Project for District. Contractor further certifies that it has instructed its employees with respect to the above- mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by Contractor if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at Contractor's expense at no additional cost to the District. Contractor has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of Contractor: Signature: Print Name: Title: END OF DOCUMENT LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California Department of Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate lead-containing paint and lead products. Because the Contractor and its employees will be providing services for the District, and because the Contractor’s work may disturb lead-containing building materials, CONTRACTOR IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a lead- based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the Contractor, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. The Contractor shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the Contractor. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. Contractor, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, the Contractor will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the Contractor to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of the Contractor to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. THE UNDERSIGNED HEREBY ACKNOWLEDGES, UNDER PENALTY OF PERJURY, THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD-BASED MATERIALS ON THE OWNER’S PROPERTY, AS WELL AS THE EXISTENCE OF APPLICABLE LAWS, RULES AND REGULATIONS GOVERNING WORK WITH, AND DISPOSAL OF, SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR. Date: Name of Contractor: Signature: Print Name: Title: END OF DOCUMENT DOCUMENT 00 61 13.13 PERFORMANCE BOND (100% of Contract Price) (Note: Contractor must use this form, NOT a surety company form.) KNOW ALL PERSONS BY THESE PRESENTS:

Appears in 1 contract

Samples: Agreement for Construction Services

ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION. ~~Contractor~~ Design-Builder hereby certifies that no Asbestos, or Asbestos-Containing Materials, polychlorinated biphenyl (PCB), or any material listed by the federal or state Environmental Protection Agency or federal or state health agencies as a hazardous material, or any other material defined as being hazardous under federal or state laws, rules, or regulations “New Material Hazardous”, shall be furnished, installed, or incorporated in any way into the Project or in any tools, devices, clothing, or equipment used to affect any portion of ~~Contractor~~Design- Builder's work on the Project for District. ~~Contractor~~ Design-Builder further certifies that it has instructed its employees with respect to the ~~above-~~ above-mentioned standards, hazards, risks, and liabilities. Asbestos and/or asbestos-containing material shall be defined as all items containing but not limited to chrysotile, crocidolite, amosite, anthophyllite, tremolite, and actinolite. Any or all material containing greater than one-tenth of one percent (.1%) asbestos shall be defined as asbestos-containing material. Any disputes involving the question of whether or not material is New Hazardous Material shall be settled by electron microscopy or other appropriate and recognized testing procedure, at the District’s determination. The costs of any such tests shall be paid by ~~Contractor~~ Design-Builder if the material is found to be New Hazardous Material. All Work or materials found to be New Hazardous Material or Work or material installed with “New Hazardous Material” containing equipment will be immediately rejected and this Work will be removed at ~~Contractor~~Design-Builder's expense at no additional cost to the District. ~~Contractor~~ Design-Builder has read and understood the document Hazardous Materials Procedures & Requirements, and shall comply with all the provisions outlined therein. Date: Name of ~~Contractor~~Design-Builder: Signature: Print Name: Title: LEAD-PRODUCT(S) CERTIFICATION California Occupational Safety and Health Administration (CalOSHA), Environmental Protection Agency (EPA), California Department of Health Services (DHS), California Department of Education (CDE), and the Consumer Product Safety Commission (CPSC) regulate ~~lead-~~lead- containing paint and lead products. Because the ~~Contractor~~ Design-Builder and its employees will be providing services for the District, and because the ~~Contractor~~Design-Builder’s work may disturb lead-containing building materials, ~~CONTRACTOR~~ DESIGN- BUILDER IS HEREBY NOTIFIED of the potential presence of lead-containing materials located within certain buildings utilized by the District. All school buildings built prior to 1993 are presumed to contain some lead-based paint until sampling proves otherwise. The CDE mandates that school districts utilize DHS lead-certified personnel when a ~~lead-~~ lead-based hazard is identified. Examples of lead-certified personnel include: project designers, inspectors, and abatement workers. Furthermore, since it is assumed by the district that all painted surfaces (interior as well as exterior) within the District contain some level of lead, it is imperative that the ~~Contractor~~Design-Builder, its workers and subcontractors fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials (Including Title 8, California Code of Regulations, Section 1532.1). Any and all Work which may result in the disturbance of lead-containing building materials must be coordinated through the District. The California Education Code also prohibits the use or import of lead-containing paint, lead plumbing and solders, or other potential sources of lead contamination in the construction of any new school facility or in the modernization or renovation of any existing school facility. ~~The Contractor~~ Design-Builder shall provide the District with any sample results prior to beginning Work, during the Work, and after the completion of the Work. The District may request to examine, prior to the commencement of the Work, the lead training records of each employee of the ~~Contractor~~Design- Builder. All contractors who disturb lead-based paint in a six-square-foot area or greater indoors or a 20-square-foot area outdoors shall comply with the Renovation, Repair and Painting Rule, shall receive training from a U.S. EPA-accredited training provider, and shall be certified by the U.S. EPA. ~~Contractor~~Design-Builder, its workers and subcontractors must fully and adequately comply with all applicable laws, rules and regulations governing lead-based materials, including those rules and regulations appearing within title 40 of the Code of Federal Regulations as part 745 (40 CFR 745). If failure to comply with these laws, rules, and regulations results in a site or worker contamination, ~~the Contractor~~ Design-Builder will be held solely responsible for all costs involved in any required corrective actions, and shall defend, indemnify and hold harmless the District, pursuant to the indemnification provisions of the Contract, for all damages and other claims arising therefrom. If lead disturbance is anticipated in the Work, only persons with appropriate accreditation, registrations, licenses and training shall conduct this Work. It shall be the responsibility of the ~~Contractor~~ Design-Builder to properly dispose of any and all waste products, including but not limited to, paint chips, any collected residue, or any other visual material that may occur from the prepping of any painted surface. It will be the responsibility of ~~the Contractor~~ Design-Builder to provide the proper disposal of any hazardous waste by a certified hazardous waste hauler. This company shall be registered with the Department of Transportation (DOT) and shall be able to issue a current manifest number upon transporting any hazardous material from any school site within the District. ~~THE UNDERSIGNED HEREBY ACKNOWLEDGES~~The undersigned hereby acknowledges, ~~UNDER PENALTY OF PERJURY~~under penalty of perjury, ~~THAT HE OR SHE HAS RECEIVED NOTIFICATION OF POTENTIAL LEAD~~that he or she has received notification of potential lead-~~BASED MATERIALS ON THE OWNER’S PROPERTY~~based materials on the owner’s property, ~~AS WELL AS THE EXISTENCE OF APPLICABLE LAWS~~as well as the existence of applicable laws, ~~RULES~~ rules and regulations governing work with, and disposal of, such materials with which it must comply. The undersigned also warrants that he or she has the authority to sign on behalf of and bind the design-builder. Date: Name of Design-Builder: Signature: Print Name: Title: Agreement For Design, Installation and Commissioning for HVAC AND ~~REGULATIONS GOVERNING WORK WITH~~EMS EFFICIENCY PROJECT IMPLEMENTATION PERFORMANCE BOND (100% of Contract Price) (Note: Respondents must use this form, ~~AND DISPOSAL OF~~NOT a surety company form.) KNOW ALL PERSONS BY THESE PRESENTS: That WHEREAS, ~~SUCH MATERIALS WITH WHICH IT MUST COMPLY. THE UNDERSIGNED ALSO WARRANTS THAT HE OR SHE HAS THE AUTHORITY TO SIGN ON BEHALF OF AND BIND THE CONTRACTOR.~~the governing board (“Board”) of the Xxxxxx Community College District, (“District”) and , (“Principal)” have entered into a contract for the furnishing of all materials and labor, services and transportation, necessary, convenient, and proper to perform the following project: (Project Name) (“Project” or “Contract”) which Contract dated , 20 , and all of the Contract Documents attached to or forming a part of the Contract, are hereby referred to and made a part hereof, and And WHEREAS, said Principal is required under the terms of the Contract to furnish a bond for the faithful performance of the Contract;

Appears in 1 contract

Samples: Agreement

Common use of ASBESTOS & OTHER HAZARDOUS MATERIALS CERTIFICATION Clause in Contracts