Alternator a. 185 ampere hour: Bosch or approved equal.
Alternator. 3.3.1. Single phase 120/240 volt, 2 pole alternator with the following characteristics.
Alternator e) Batteries;
Alternator. The alternator shall be of sufficient output to meet the electrical demand of the vehicle. A dual belt drive or equivalent shall be used. QACPS – AC system – 200 amp, lift and AC – 275 amp.
Alternator. Kirlosker, Greaves, Stampford, Jyoti
Alternator. Make: ………………………… Type: ………………… Speed of rotation: . (nominal speed given by the manufacturer: ( (… rpm ( (minimum speed: rpm Refrigerant fluid: ……………………………………………………………………………………….. Heat exchangers Condenser Evaporator Make-type Number of tubes Fan pitch (mm)2/ Tube: nature and diameter (mm)2/ Exchange surface area (m2)2/ Frontal area (m2) FANS Number Number of blades per fan Diameter (mm) Nominal power (W)2/3/ Total nominal output at a pressure of Pa (m3/h)2/ Method of drive Expansion valve: Make: ………………………….. Model: …………………………………… Adjustable: 1/ ………………….. Not adjustable: 1/ …………………. Defrosting device: ……………………………………………………………………………………… Automatic device: ……………………………………………………………………………………… Minimal Nominal Speed of Rotation .............. .......…. ……….. .………. .……… ….. .............. ......….. ……….. .………. ..……… ….. rpm Fans 3/ .............. ......…… .…….. ……..… .……… ….. .............. ......….. ……….. .………. ..……… …. rpm Alternator 3/ .............. .......…. ……….. .…….… .……… …... .............. .......… ……….. ……….. ……… ….. rpm Compressor 3/ .............. .............. .............. .....…..... …….… …. .............. .............. .............. ..........… ..……… W Power of internal fan heater ............ ............ ............ ............ ........… ............ ............ ............ ............ ........... W Power absorbed by the unit cooler fan 4/ .............. .............. .............. .............. .............. .............. .............. .............. .............. .………. W or l/hr Fuel or electrical power consumption .............. .............. .............. .............. .............. .............. .............. .............. .............. ............ …... °C Mean temperature around the body ............ ............ ..…..… …....… …..… ............ ............ ....…… ..…… ……… °C Mean Internal temperature ............ ...….... ……… ..…..… ……… ............ ............ .…….. …...… ……… °C Inlet to evaporator
Alternator. Backup light switch, Brake light switch, manually operated switches, Neutral safety switch, Pulley and mounting bracket, Propulsion battery, Starter drive, Starter motor, Starter solenoid, Voltage regulator, Wiper motors, Wiring harnesses.
Alternator starter, battery, battery terminal, oil sensor, spark plugs and wires Mass air flow sensor, cam sensor, throttle position sensor, low coolant sensor, oxygen sensor, air change temperature sensor, electronic control module and related sensors, and coil packs TRANSMISSION All internal lubricated parts, seals, torque converter, andtransmissions case Standard transmission clutch parts, flex plate, transmission mounts,transmission fluid lines, throw out bearing FRONT WHEEL DRIVE Axle shafts, axle seals, final drive housing and internal parts, front-wheel bearings, u-joints, inner and outer tie rod ends, stabilizer bars, steering rack and pinion, idler arms, upper and lower ball joints, steering linkage and power steering pump Shocks, struts, strut plates, springs, front end alignment (unless required with covered repair) REAR WHEEL DRIVE Axle shafts, drive-axle housing and internal parts, driveshaft, rear wheel bearings, retainers, u-joints, axle seals, ball joints, stabilizer bars, and drive shaft bearing Shocks and struts HEATING AND COOLING N/A Air Conditioning recharge, clutch, blower motors, refrigerant, hoses, o-rings, evaporators, condensers and any other air conditioningrelated parts / or heating components x x N/A
Alternator. There shall be a Xxxxx Xxxxxxx Model 4949PA, 270 amp, serpentine belt driven alternator or equivalent. The installation shall include a brush less design with an integral self-diagnostic regulator and rectifier for compact installations. The alternator installation shall be designed to provide maximum output at engine idle speed to meet the minimum continuous electrical load of the apparatus as required. BATTERY SYSTEM Five (5) Exide #HP-31D, Group 31, maintenance free batteries shall be provided. Each battery shall be rated at 925 CCA at 0° F and shall have a reserve capacity of 180 minutes. Wiring for the batteries shall be 4/0 welding type dual path starting cables for SAEJ541. BATTERY STORAGE Batteries shall be securely mounted in fixed 3/16” GR50 steel trays located on each side of the chassis frame. Complete access shall be provided when the cab is fully tilted. Batteries shall be mounted on non-corrosive matting material. The battery tray shall be able to withstand a longitudinal acceleration of -46.5g at 0.246 seconds in accordance to SAE J211 standards using a channel frequency class 600 filter. Testing shall be performed at and verified by a third party testing and evaluation center.
Alternator. The Alternator shall be of the low harmonic type, rated for 400V, 50Hz.
