Test Certificates. GlobalSign may provide or support issuing Certificates for testing and evaluation purposes, including but not limited to trial evaluation, interoperability testing and proof-of-concepts (“Test Certificate(s)”). Subscriber may only use a Test Certificate in an internal, non-production environment and as part of non- commercial evaluation. The right to use a Test Certificate may be limited in time and further restricted in additional agreements between Subscriber and GlobalSign, in which case Subscriber’s right to use will be terminated after the end date specified. GlobalSign may at its sole discretion terminate the right of use of any Test Certificate at any time. Subscriber shall cease the use of the Test Certificate upon such termination. Warranty Disclaimer. SUBSCRIBER ACKNOWLEDGES THAT TEST CERTIFICATES ARE PROVIDED “AS IS” AND WITHOUT ANY WARRANTY WHATSOEVER. TO THE MAXIMUM EXTENT ALLOWED BY APPLICABLE LAW, GLOBALSIGN EXPRESSLY DISCLAIMS ALL REPRESENTATIONS AND WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT, RELATING TO ANY TEST CERTIFICATES, SUBSCRIBER’S USE OR ANY INABILITY TO USE A TEST CERTIFICATES, THE RESULTS OF ITS USE AND THIS AGREEMENT. LIMITATION OF LIABILITY. GLOBALSIGN SHALL NOT BE LIABLE TO SUBSCRIBER FOR ANY CLAIMS, DEMANDS OR DAMAGES WHATSOEVER, INCLUDING, WITHOUT LIMITATION, DIRECT, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES, ARISING OUT OF THE USE OF ANY TEST CERTIFICATES AND THE USE OR FAILURE OF A TEST CERTIFICATE TO OPERATE FOR WHATEVER REASON, WHETHER SUCH ACTION IS BASED IN CONTRACT OR TORT OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, NEGLIGENCE.
Test Certificates. Failure to supply test certification in compliance with the Quality Assurance Scheme will deem this Agreement incomplete and no payment will be made until the certification is received and accepted by the Purchaser. The Supplier must provide verification of current ISO certification annually to the Purchaser.
Test Certificates. Three copies of test certificates of (i) chemical composition, (ii) mechanical test shall be furnished. The test certificates shall be signed by Third Party Inspectors.
Test Certificates. For each batch supplied to Datwyler, there shall be an appropriate laboratory/quality determination of satisfactory conformance to the agreed specifications, if applicable. The provider shall supply released materials to Datwyler with a certificate of Analysis (CoA) or Certificate of Conformity (CoC). The CoA shall be signed by the Quality Assurance representative indicating that all requirements were met in accordance with pre-determined agreed upon specifications. This certificate shall include standard values, the tolerances and the actual readings that have been measured. The documented product characteristics and sample size shall be agreed with Datwyler.
Test Certificates. The Contractor shall be required to submit recent Test Certificates for the materials being used in works from the recognised laboratories if additionally insisted. These certificates should indicate all properties of the materials as required in relevant BIS or International Standards. 17.0
Test Certificates. When instructed by the Engineer the Contractor shall submit certificates of Test from the suppliers of materials and goods to be used for contract to the Engineer. Such certificates shall certify that the materials or goods concerned have been tested in accordance with requirements of the Specification and shall give the results of all the tests carried out. The Contractor shall provide adequate means of identifying the materials and goods delivered to the site with the corresponding certificates. For termination of incoming and outgoing cables, epoxy insulators with studs and locknuts shall be provided.A detachable gland plate made out of 3 mm thick galvanized iron/aluminum sheet shall be provided at the pillar bottom. For automatic ON/OFF operation of the street lights, quality make electronic photocell shall be provided in the street light control pillar. The Contractor shall ensure that the necessary energy meter is provided by the power supply company (KPLC) and the necessary documentation done. Cables at feeder control pillar shall be terminated at the bottom glad plate, by heavy duty compression type of gland plate, earthing tags for effective earthing of cable armour and PVC cable shroud shall be provided. Feeder control pillar foundation shall be Class20/20 Concrete, 200 mm above ground level. . 0 E a xx x x x x 5.1 Earthing for Light Feeder ControlPillar Earth rod copper electrode of 38 mm. dia 2500mm long shall be provided with a clip on the top and sharp end for driving it in ground. The earthing lead should not be less than 6mm² green/yellow cable. Earthing resistance shall not exceed more than 3 Ohms. . 2 E a xx x x x x One number with 25 mm diameter 1800mm long copper earth rod electrode shall be provided for every fourth pole. For earthing of the poles and pillars single core at least 6mm² earth wires yellow/green from each earthing electrodes shall be connected with nuts and washers to the earthing bolts welded to the pillars and pole. For earthing of the lighting fitting the third core of the lead wire shall be used and connected between pole terminal boxes to the fitti
Test Certificates. Copies of all relevant test certificates shall be provided in duplicate.
Test Certificates. Two copies of all routine-test certificates must be supplied to the Employer prior to take over of the switchboard.
Test Certificates. Three copies of test cer tificates consisting of mechanical pr operties and chemical composition of the metals shall be fur nished. 7.0
Test Certificates. 10.1 Agreed test certificates as per EN 10204 shall accompany each delivery in accordance with the type of delivery. A further copy shall be kept by the SUPPLIER.
