Apparatus Clause Samples

Apparatus. Instrument and/or equipment obtained in connection with the project and charged to the Client shall remain the property of the University unless otherwise it is specifically agreed by the University.

Apparatus. Instruments and/or equipment obtained in connection with the project and charged to the client remain the property of AMU, Aligarh, unless otherwise it is specifically agreed to by the Institute.

Apparatus. Instruments and/or equipment obtained in connection with the project and charged to the client remain the property of IIT Ropar, unless otherwise it is specifically agreed to by the Institute.

Apparatus. 10.4.1. Combustion chamber (figure 15), preferably of stainless steel, having the dimensions given in figure 16. The front of the chamber contains a flame-resistant observation window, which may cover the entire front and which can be constructed as an access panel. The bottom of the chamber has vent holes, and the top has a vent slot all around. The combustion chamber is placed on four feet, 10 mm high. The chamber may have a hole at one end for the introduction of the sample holder containing the sample; in the opposite end, a hole is provided for the gas-supply line. Melted material is caught in a pan (see figure 17) which is placed on the bottom of the chamber between vent holes without covering any vent hole area. 10.4.2. Sample holder, consisting of two U-shaped metal plates or frames of corrosion- proof material. Dimensions are given in figure 18. The lower plate is equipped with pins and the upper one with corresponding holes, in order to ensure a consistent holding of the sample. The pins also serve as measuring points at the beginning and end of the burning distance. A support shall be provided in the form of heat-resistant wires 0.25 mm in diameter spanning the frame at 25-mm intervals over the bottom U-shaped frame (see figure 19). The plane of the lower side of samples shall be 178 mm above the floor plate. The distance of the front edge of the sample holder from the end of the chamber shall be 22 mm; the distance of the longitudinal sides of the sample holder from the sides of the chamber shall be 50 mm (all inside dimensions). (See figures 15 and 16). 10.4.3. Gas burner

Apparatus. The Apparatus shall at all times throughout the Term remain the property of the Tenant and shall not form part of the Premises or be or become the property of the Landlord.

Apparatus. [add specification of the type of apparatus to be installed]

Apparatus. The Company agrees to sell, and the Buyer agrees to purchase One (1) KME Custom Pumper Apparatus (collectively hereinafter referred to as “Apparatus”) described in the Company’s quoted proposal per the Buyer’s Specifications, which are attached hereto and hereby incorporated herein, all in accordance with the terms and conditions of this Agreement. Delivery to City of Yakima to be approximately 820 days from receipt of executed contract. Completion of the pre-construction conference shall be conducted virtually within 60 days from execution of contract. The Seller shall not be charged with liquidated damages or any excess cost if any delay of the delivery of goods is due to: • Any preference, priority of allocation order duly issued by any governmental agency. • Unforeseeable causes beyond the reasonable control of Seller and without the fault, or negligence of the Seller, including but not restricted to, acts of God, or of the public enemy, acts of the Buyer, fire, flood, epidemics, quarantine restrictions, strikes, freight embargoes, and natural disasters • Product shortages, tariffs or product interruptions due to trade disagreements or supply chain disruptions. Provided that the Seller shall, within seven days from the beginning of such delay, notify the Buyer, in writing, of the causes of the delay whereupon the Buyer shall ascertain the facts and extent of the delay and notify the Seller within a reasonable time of its decision in the matter.

Apparatus. Commented [SBG13]: County made revisions in this section to clarify. The County shall provide at a minimum the following apparatus to the Jupiter Service Area: Three (3) Command Vehicles One (1) Support Vehicle Two (2) Brush Trucks Three (3) Engines Three (3) Rescue Units

Apparatus. 4.1.1. Abrading instrument 2/ shown diagrammatically in figure 4 and consisting of: A horizontal turntable, with centre clamp, which revolves counter-clockwise at 65 to 75 rev/min.;