Windshield a. Pinpoint chips are non-chargeable providing the glass is not sandblasted. Sandblasted glass is defined as a series of pinpoint chips in a concentrated area.
Windshield. 19.51.1. Tint only: The windshield shall be tinted throughout.
Windshield. (5) Rear window and other glass;
Windshield. Air conditioning on highway equipment delivered after July steering wheel and power steering Re-grooved tires will not be installed on power units
Windshield. The windshield shall permit an operator's field of view as referenced in SAE Recommended Practice J1050. The vertically upward view shall be a minimum of 15°, measured above the horizontal and including any shaded band. The vertically downward view shall permit detection of an object 3 ½ feet high no more than 2 feet in front of the Trolley. The horizontal view shall be a minimum of 90° above the line of sight. Any binocular obscuration due to a center divider may be ignored when determining the 90° requirement, provided that the divider does not exceed a 3° angle in the operator's field of view. Windshield pillars, center or A, shall not exceed 10° of binocular obscuration. The windshield shall be designed and installed to minimize external glare as well as reflections from inside the Trolley. When operated at night with the passenger interior lighting on, essentially no reflections shall be visible in the windshield immediately forward of the operator's barrier. Reflections in the remainder of the windshield shall be minimized, and no reflection of any part of the interior behind the operator's barrier shall be visible in the windshield. The windshield glazing material shall have a 6-mm nominal thickness laminated safety glass conforming to the requirements of ANSI Z26.1 Test Grouping 1A and the Recommended Practices defined in SAE J673. The glazing material shall have single density tint. The upper portion of the windshield above the operator's field of view shall have a dark, shaded band with a minimum luminous transmittance of 6% when tested in accordance to ASTM D- 1003.
Windshield. Any scratch, Pitted, chips or scratches less than one inch in length but which are in the critical area of the driver’s vision or which will not pass safety inspection are considered abnormal wear and tear.
Windshield. The cab windshield shall be of a two-piece replaceable design for lowered cost of repair.
Windshield. The windshields shall be removed and replaced with new meeting OEM specifications. The rubber gaskets shall be replaced. 17.17 Window Regulators New window regulators shall be installed. 17.11
Windshield. A one (1)-piece, safety glass full width windshield with more than 3,228 square inches of clear viewing area will be provided. No Exceptions. The windshield shall feature: A completely uninterrupted view from both the driver and officer positions The windshield will consist of three (3) layers; the outer layer, the middle safety laminate, and the inner layer. The .114" thick outer light layer will provide superior chip resistance. The middle safety laminate layer will prevent the windshield glass pieces from detaching in the event of breakage. Economical replacement readily available from auto glass supplier Easily removable for replacement using standard automotive techniques A frit band will be provided along with an outer trim seal on the outside perimeter of the windshield for a finished automotive appearance. One (1) Windshield Wiper System Single Motor (2) Wipers 03-08-0102 WINDSHIELD WIPER SYSTEM A single windshield wiper system shall be incorporated in conformance with FMVSS and SAE requirements. Two (2) 22" windshield wiper arms shall be mounted below the windshield. Each arm shall include a 26" long wiper to provide optimum windshield clearing. The windshield wiper fluid reservoir can be filled without raising the cab. One (1) Windshield Wiper Activation Switch on Driver Panel 08-02-0135
Windshield use liquid commercial grade glass cleaner. Do not use abrasive cleaners (GEM CARS ONLY; N/A FOR CLUB CARS). 9 Clean exterior of vehicle.
