POCKETS Clause Samples
POPULAR SAMPLE Copied 1 times
POCKETS. Two (2) B.DU style patch pockets are on the chest with 1-1/4” box pleat, stitched top and bottom to prevent spreading. Pockets are topstitched 1/16” from the edge, with square corners, to finish 5-3/4” wide by 5-3/4” long. The left chest pocket shall have an internal pencil compartment 1-1/2” wide corresponding to opening on flap. • Hidden napoleon or notebook pockets on the left and right sides are under the chest patch pockets and close with hook and loop, measuring 5/8" wide by 2" long. Notebook pocket opening measures 6-1/4”, shall be secured with 1 vertical bar-tack at the bottom of the opening on both sides. Style has two (2) asymmetrical flaps, with 1/4” double needle topstitching, to finish 5-3/4” in width, by 2-3/4” long at outer sides, and 2-1/4” at front side. Flaps are secured to the front of the shirt with two rows of stitching 3/16” apart. Left flap has a 1-1/4” pencil opening corresponding to pencil compartment inside the pocket. Flaps have woven interlining of stabilized fusible. Creased and edge stitched pocket flap construction is unacceptable. The side points of the flaps are to be secured to the pocket by means of hook and loop fasteners sewn onto the flaps and pockets, the hook portion being stitched to the pocket and loop portion sewn to the underside of the flap. The loop piece sewn to the flap shall not be sewn through and through the flap, but must be attached during the manufacturing process before the flap is assembled to prevent the stitching from showing.
POCKETS. There are 6 pockets assembled from internal construction fabric as follows:
POCKETS. Has two (2) lower welt pockets made of Softshell fabric and 1 ply interlining with zipper closure. Side pockets opening towards side seam on slight angle and measures 7”. There shall be a zippered napoleon pocket on wearer left side open towards center front measuring 6” (regular length). Pocket bags constructed with 1 layer brushed flannel fabric and 1 layer tricot. Zippers close from bottom to top.
POCKETS. Two (2) lower scalloped flaps, no pockets, two (2) breast pockets pleated patch pockets with scalloped flaps. Lower and breast flaps to button with gilt "P" buttons. One (1) inside reinforced breast pocket piped with same material 6" wide and 7" deep.
POCKETS. Outside pocket consisting of two (2) lower scalloped flaps, with hidden pocket beneath with 5” horizontal opening and 5 3/4” depth and two (2) breast pleated patch pockets with scalloped flaps. Lower and breast flaps to button with 24 ligne gold plate State of Vermont buttons in center point. Two (2) inside reinforced breast pockets piped with same material 6" wide and 7" deep.
POCKETS. The front pocket opening will be a minimum 6” and be 5½” deep from the bottom of the opening. They shall be stitched, turned, and restitched. The inside front pocket facing shall be a separate piece of self-material finished no less than 1¼” wide. There shall be a non-woven interlining fused to the front pocket facing to give additional stability and strength to the pocket. The back pockets will have a minimum opening of 5½” on sizes 10 and above, and 5” on sizes 8 and below, and be 6” deep. They shall be made with a ▇▇▇▇▇ ▇▇ automatic machine and finished on the outside with an exposed top and bottom cord. The left pocket shall have a tab to button. The front pockets shall have straight bartacks and the back pockets shall be bartacked with triangular bartacks.
POCKETS. When exterior pockets are specified, the following requirements shall apply to all such custom option specified exterior pockets: All pockets and flaps shall be reinforced at the top comers with bar tack stitching. All pocket shall be reinforced with an extra layer of NFPA-certified outer shell, moisture barrier, or other NFPA-certified reinforcement material for extra durability. The exact location of the reinforcements shall be identified in the custom options section(s). All pockets shall have a means to drain water and shall have a means of closure. All pocket closures shall be made either with hook and loop fastener tape a minimum of 1.5 inches (3.8 cm) wide, with a flap, or with snaps. The specific placement of the closure system shall be outlined in the custom options sections.
POCKETS. Two breast patch pockets with mitered corners and 1-1/4" stitched pleats. Pleats shall be stitched top and bottom and full length of pleat to prevent spreading. Pocket to measure 5" wide, 6-1/4" deep. Breast pockets are set to shirtfront with ¼” double needle stitching. Left breast pocket to have 1- 1/4" pencil stitch. Each pocket shall have a well-sewn buttonhole eyelet centered on the pocket to align with the buttonhole in the pocket flap. Black Pocket Flaps to be two-piece mitered design to measure 5-1/4" across and 2-1/8" in depth at center, 1-1/2" at sides. Secured to shirtfront approximately 3/8” above pocket. Each flap to have invisible pencil opening 1-1/4" to correspond precisely with pencil slot of pocket. (Stop & start stitching for pencil opening unacceptable and shall be cause for rejection.) Flaps to be 1/4" double needle topstitched. Flaps to have woven interlining of #550 Stabilized ▇▇▇▇▇-Press. Creased and edge stitched pocket flap construction unacceptable. Each flap shall have a buttonhole centered on the flap to align with the buttonhole eyelet on the pocket.
POCKETS. Two breast patch pockets with mitered corners and 1-1/2" stitched pleats to be sewn over the map pockets. Pleats shall be stitched top and bottom and full length of pleat to prevent spreading. Pocket to measure 5-5/8" wide, 6" deep. Left breast pocket to have 1- 1/2" pencil stitch. Each pocket to have hook Velcro, 3/4" long by ½" wide, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Two piece deep scalloped design to measure 5-7/8" across and 2-3/4" in ▇▇▇▇▇ ▇▇ ▇▇▇▇▇▇ ▇▇▇▇▇, ▇-▇/▇" at sides. Secured to shirtfront approximately 3/8” above pocket. Left flap to have invisible pencil opening 1- 1/2" to correspond precisely with pencil slot of pocket. (Stop & start stitching for pencil opening unacceptable and shall be cause for rejection.) Flaps to be 1/4" topstitched. Flaps to have woven interlining of #250 Dacron. Creased and edge stitched pocket flap construction unacceptable. Under side of the flap to have looped Velcro 3/4" long by 1/2" wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket. Each flap shall have a button centered on uncut sewn buttonhole.
POCKETS. The two (2) front pockets will be quarter top style with a minimum opening of 7" and a minimum depth of 5-3/4" measured from the bottom of the opening. Front pockets to have firm straight bartacks at top and bottom of pocket openings. Pockets shall be constructed using the stitch, turn, and topstitch method. Front pocket facing and barrier to be made of the basic trouser fabric. Facing shall be a minimum of 1” and barrier shall measure a minimum of 2" (measured to the inside edge of pocket lining). that there is no topstitching (topstitched hip pockets shall be cause for rejection). The corners of the hip pocket openings shall have straight bartacks for reinforcement (use of triangular bartacks shall be cause for rejection). Hip pocket facing and barrier are to be made of basic trouser fabric. Facing shall be a minimum of 3/4” and the barrier shall be a minimum of 1-1/2". The left hip pocket shall have a centered tab made of basic cloth inserted into the top welt with bartacks at the top and bottom of the tab to form an opening for a button. A button shall be located below the bottom welt corresponding in location with the tab, which shall be interlined with non-woven for added durability. There shall be a dart centered above each hip pocket to waistband. Dart shall be approximately 2-3/4” long tapered from 3/8” at waistband and shall be installed with automatic equipment for a clean non-puckered finish. The watch pocket shall be located on the right front at the waistband. This pocket shall have a minimum opening of 2-5/8” and a minimum depth of 2-7/8". The front of the pocket shall be made of pocketing fabric and the back of the pocket shall be made of basic fabric and the two pieces are securely stitched together. Each corner of the pocket opening shall have firm straight bartacks.